DIY comb. Do-it-yourself wooden combs - master class How to make a brush with your own hands from wood

A great gift for a girl, even if... this moment she wears short hair. Perhaps in a couple of years she will want long curls and a comb will come in handy. In addition, none of your friends will definitely have the original comb with a figurine of a sleeping cat!

Materials for making the comb:

  • a piece of hardwood (such as tatachuba, teak or birch) 8mm thick
  • stain on water based
  • teak oil.

Tools for making a comb:

  • jigsaw
  • pencil
  • wood cutters
  • sandpaper
  • brush.

How to make a hair comb with your own hands

We draw the contours of the ridges on the tree. The diagram is attached.

Using a jigsaw, we cut out the ridges along the contour.

We clamp a sheet of sandpaper into the holder. We need to grind the workpiece at an angle to the ends so that the combs fit into the hairstyle more easily.

Now we take small pieces of sandpaper and round all the corners, especially carefully rounding the ends. Combs without seals are already ready to be coated with stain and oil.

Seal combs are a little more complicated. We select cats along the contour using incisors. The main thing is to take your time and periodically sand the cat figurine with small pieces of sandpaper. The lines should be smooth and flowing.

We tint the combs with water-based stain (1-3 layers). Let it dry thoroughly for a couple of hours.

Apply teak oil liberally and leave for 15-20 minutes.

Remove excess oil with a paper towel or rag. After 3-4 days, the oil will be absorbed and the comb will be ready for use.

All that's left to do is make the gift wrapping!

Making a wooden comb is not that difficult if you have the opportunity to work on woodworking machines. First of all, we need a board, even if not edged, the thickness is also not important here. We will make a comb from it and, accordingly, reduce it to the size we need.

The website dslaboratories.ru presents professional hair care cosmetics. Using a circular saw we cut the board to a thickness of 6 mm, this is very difficult. Therefore, make all the markings in advance, especially since you will have to work along the material. It’s better, of course, to play it safe and do everything slowly.

We choose the width and length of the comb ourselves, approximately 2 cm and 12 cm. This will be enough; there is no need to use a large comb either. As soon as the workpiece is ready, we begin to cut teeth on it.

Most likely, we will proceed from the parting frequency. This means we make teeth 1.5 mm thick, and the distance between them is 1 mm. Although you can divide it into two parts and make the other half larger.

We perform all manipulations on a circular saw, therefore, we exercise maximum caution. It is advisable to use protective equipment so that the chips do not get into your eyes. After you have finished cutting out the teeth, you need to polish the comb.

You can apply sandpaper or a machine, only with a fine-grained wheel. Upon completion, we scrub it thoroughly, varnish it and it is ready for use. In principle, the comb is ready, the main thing is not to pull the hair too hard so as not to break the teeth.

  • Sewing a leather bag is not that difficult, although the process is more creative than physical. You will need materials that can be found in the store or use those that you have at home. How
  • Stow floor tiles It may not be that difficult, but you need to have certain knowledge. Most of all, she doesn’t like unevenness, so first of all we level the base. Since there is to be
  • Perhaps there is not a single stage of work performed during the construction of a house where edged boards are not involved. With its help, foundations are poured, frames and doors are made, and construction
  • Every girl loves to experiment with her hair and different hairstyles. Naturalness has always been and will be in fashion, so it makes no sense to do neat and complex hairstyles during the day. Even
  • If you've ever had to remove a drilled-out piece of wood from a hole saw, you know how difficult it can be to remove it without damaging it. With a simple grip, you can easily pull out

Today we will create a hair comb with our own hands from wood. The craft is complex and requires special skills and unusual tools. With the help of such a comb, girls can pin up stripes or use them as decoration.

Tools and materials:

1. A piece of wood, 8 millimeters thick;
2. Wood coating oil;
3. Stain;
4. Pencil;
5. Jigsaw and cutters;
6. Sandpaper;
7. Brush.

Everything you need is shown in the photo.

How to make a hair comb

Let's take it wooden blank and place the patterns cut out of paper on it. Draw along the outline with a pen or pencil.

For clarity, here is an example of our craft. You can print and cut out the sample.

The most difficult thing is to cut out the scallops with a jigsaw.

We smooth out the unevenness with sandpaper, remove the angularities at the edges so that the comb fits well into the surface.

Then we take finer sandpaper and polish. Those blanks that are without seals can already be coated with stain and varnish.

We draw the cat in the right place and carefully, using cutters, cut out the figure manually. We clean each stage in a timely manner with sandpaper.

We paint the homemade products with stain and let them dry completely. Then we repeat this in several layers.

Cover with special teak oil. We wait until it dries completely. If necessary, blot it with napkins.

A comb is one of the most necessary items for both women and men. We use it daily. And the condition of our hair will depend on how well it is made. This is especially affected by the material from which this thing is made. The best option, of course, is a wooden object. Wood does not electrify the hair, unlike plastic. It is natural and has its own unique aroma. But it’s rare to find such an item on sale, so it’s best to make it yourself.

Before you start, you need to prepare everything you need. In this case it will be useful following materials and tools.

  • A wooden block (plate) with the following parameters: length - 12 cm, width - 10 cm and thickness - 0.8 cm.

Attention! From various species, it is better to choose pine, apple or birch.

  • Pencil, ruler.
  • Jigsaw or file.
  • Sandpaper.

How to make a comb from wood

Once everything you need has been prepared, you can begin creating.

Let's take a closer look this process in the simplest way.

Completing of the work

  • First, sand the workpiece until it is perfectly smooth.
  • Using a pencil and ruler, mark the future teeth from the bottom edge. The width of one tooth is 0.3 cm, and the distance between them is 0.2 cm.
  • Carefully cut out the teeth using a jigsaw.
  • If desired top part products can be made curly shape and also decorate with carvings.

Advice! Beautiful decor An ornament made using burning can serve as an ornament.


  • Now sand the workpiece thoroughly.
  • Then the product is coated with stain or varnish.

Comb with handle

You can also create a regular comb with a handle.

  • To do this, take a double length, half of which will be needed for the handle. It is cut at the preparation stage, may have a simple appearance or be performed in a complex figured form.

Teeth layout options

In the same way, you can make two rows of teeth on both sides.

Or there may be two sizes of teeth in one row.

Which option to use for creation is up to everyone to choose for themselves.

1) Cut using a hacksaw or circular saw from a plank shape 8 by 10 cm.

2) Afterwards the surface is polished. We use a polished wheel.

3) It is required to draw the geometry of the blank for the ridge.

4) Then cut along the contour using a saw.

5) The teeth are cut out on a comb using a circular comb with a blade width of 1.5, and the width of the teeth is left at 2.5 mm. You can also use another value.

6) When the teeth are cut, it is necessary to sharpen the plane of the comb at the edge.

7) Now you need to grind the teeth (sharpen) using a special nozzle and clean the grooves.

8) Then the final look is achieved using sandpaper - zero.

Useful tips for making wood combs regarding sanding

  1. If you need to attach the skin to the surface, this can be done using simple silicate glue (stationery glue). Polymer adhesives soften when heated and rebound.
  2. If the skin is round, it is better to place it on a piece of vacuum rubber, in the center of which there is a metal axis. When installing the nozzle, press the washers on both sides. The skin is removed when the washers are relaxed.
  3. When initially making combs from wood, you can use a board from packing boxes - this will help in making good options combs and learn to do more serious things.
  4. Don't be afraid to experiment with shape, size, etc. personal experience we will not replace.