Repairing a toilet with panels: quick transformation without extra expenses (52 photos). Design of a toilet finished with plastic panels Repair of a toilet with a black toilet with plastic panels

When choosing cladding for the walls and ceiling of a toilet, one must be guided by considerations not only of aesthetics, but also of hygiene: ideally, the coating should be smooth and easy to clean. Accordingly, moisture resistance is also required.

Today, in addition to expensive ceramic tiles, only PVC plastic panels for the toilet satisfy these requirements.

As for the ceiling, here they are generally the only truly acceptable cladding option. Let's see how the toilet is finished plastic panels (PVC plastic) and how to choose the right material.

Cladding with plastic panels can be done in two ways:

The material is glued to the wall and ceiling like ceramic tiles. In this case, the room loses almost no volume, but this method can only be used on perfectly flat surfaces. Tile adhesive or “liquid nails” are used.
The panels are attached to the frame. A method in demand for uneven walls. The cladding will turn out to be perfectly smooth without labor-intensive “wet” processes - plastering, putty, etc. But the volume of the room will decrease more than in the first option.

The toilet is paneled

We will consider the option with a frame - as it is more complex.

Preparation for finishing work

So, there is no need to level the walls and ceiling. However, you still have to do some work in advance. Let's look at them all in order.

Taking measurements

First of all, you need to find out what and how much you need to purchase to complete the cladding. Let's go through the list:

PVC panels

The amount of base material is determined quite simply: the area of the walls and ceiling to be finished is calculated, after which a margin of 15% is added to the result obtained. It is necessary to provide a reserve: when trimming, some of the panels will go to waste, some of them may be damaged.

Ready-made repairs with plastic panels

It would seem that if something happened, the missing elements could be purchased in addition, but there is one thing: parts from another batch will most likely have a slightly different shade in comparison with those already purchased. Therefore, everything needs to be purchased at one time in a known sufficient quantity.

Profiles

These are additional elements with which the corners and edges of the finish are formed. There are several varieties:

Starting bar: frames the finish in the place where it adjoins the surface without finishing, and forms an internal angle with it.
Ceiling plinth: This is the same starting bar, only with a more interesting shape. Used to frame ceiling cladding.
F-profile: frames the edge of the finish in the place where it adjoins the uncoated surface, and forms an outer corner with it.
Corner: It can be external, internal and universal. This detail forms the junction of two lined surfaces.
H-shaped profile: used for extending the length of short panels.

Accessories for plastic panels

In general total length ceiling plinth is equal to the perimeter of the toilet ceiling. You will need an internal corner; the total length is equal to the height of the room multiplied by 4. Other details must be selected according to the situation.

Frame details

The frame for mounting plastic panels is assembled both from profiles specially designed for them, and from profiles for installation plasterboard structures. In the first case, structural elements can be made on the profiles, to which plastic panels are snapped - then they will not need to be screwed with self-tapping screws.

When assembling the frame, two types of elements are used:

Guide profile (U-shaped): It is screwed around the perimeter of the surface to be finished and is used for fastening fittings (starting strip or corner) and intermediate frame profiles.
Rack profile (C-shaped): It is used to make the very intermediate elements that are installed at equal intervals over the entire surface and to which the plastic panels will be screwed.

The required number of rack profiles is taken on the basis that they will be attached in increments of 50 - 60 cm.

Suspensions

Used for ceiling cladding. The hangers are screwed to the ceiling, after which intermediate frame profiles are attached to them. It is impossible to screw the profiles directly to the ceiling - there will be no space behind the cladding to install built-in lamps.

Suspensions are installed along each intermediate profile in increments of 45 - 50 cm.

Dowels and screws

Dowels. With their help, hangers and frame profiles are screwed to permanent structures. We calculate the quantity based on the installation step of 40 - 50 cm.
Self-tapping screws 15 - 20 mm long. With their help, the panels are screwed to the frame. Optimal step specified by the panel manufacturer.

Selection of material for construction

First of all, you need to know that plastic panels are divided into two types:

Wall: they are characterized by increased strength and cost accordingly.
Ceiling: they are less durable, since it is almost impossible to damage the lining on the ceiling through negligence. They are cheaper than wall ones.

The panels also differ in size. IN small room narrow panels called slats or plastic lining should be used. If you do the opposite and use large parts, the toilet will seem very small and cramped.

The toilet walls are lined with PVC

Those who pay special attention to design will certainly find the option of installing special decorative inserts between the panels interesting.

An important issue is the quality of the panels. Here's what you need to pay attention to:

Stiffening ribs inside the product should be located as often as possible.
The front side must be absolutely smooth. If you can see stiffening ribs underneath, you are looking at a low-quality material.
The thicker the plastic, the better. Please note: we are not talking about the thickness of the panel as a whole, but specifically about the thickness of all its components - the outer sheets and internal ribs. To check, you need to squeeze the panel with two fingers. If the ribs are bent and dents remain on the surface, it is better to refuse to purchase this brand.
Plastic should not be brittle, for which special additives are added to it. Manufacturers of cheap types strive to save money on such an additive. Fold the strip to the edge of the panel, which is used to snap the adjacent piece in place. If there is a dent in the bend area, and even more so if the plastic is cracked, it is clearly of poor quality.
Immediately discard material from strong odor. It indicates that the plastic gases, that is, it emits volatile substances that negatively affect health.
The appearance of the panels must be impeccable: the color is uniform, the pattern is clearly printed.

If you have any doubts, do not hesitate to request to see the certificate.

Required Tools

Except finishing material To work you need to prepare the following:

plumb line;
level: it is advisable to have both bubble and water;
hammer drill or impact drill;
screwdriver or screwdriver;
hacksaw or jigsaw;
metal scissors;
roulette;
roller and brush;
a spool of nylon thread;

Have a marker or pencil.

Preparing the surface for finishing

The purpose of this stage is to prevent the development of mold and mildew on surfaces hidden under the cladding.

Here's what to do:

Previous finishes that may pose a potential hazard are removed. This concept refers to any wallpaper, areas of painted surfaces on which the paint has peeled off. If the wallpaper is still holding tightly, it needs to be soaked warm water(this is convenient to do with a roller), after which it will be quite easy to remove them.
Next, an antiseptic primer is applied to the surface with a roller.

Carrying out the cladding

How to sheathe (finish) a toilet with plastic panels?

The finishing is installed as follows:

First, the frame is installed. To cover the ceiling, a guide profile is screwed onto the walls along the entire perimeter, departing the required distance from the ceiling. These elements must be in the same horizontal plane, so markings for them must be applied using a water level.
Next, nylon threads are pulled between the guide profiles to indicate the horizontal plane, and then, guided by them, intermediate profiles are installed on hangers.
When finishing a wall, you first need to use nylon threads to mark vertical plane, for which a plumb line is used. Next, sections of the rack profile are screwed to the wall so that their edges lie in the designated plane. In places where the wall surface has deflections, pads must be installed under the profile.
Next, starting strips (for wall cladding) or ceiling plinths (for ceilings) are attached to the frame.
Having freed the first plastic panel from protective film and having been cut to length, one side is brought under the starting profile and screwed to the frame with self-tapping screws.
The remaining panels are installed in the same way. Lamps must be installed and checked during installation, so that later if the lighting system does not work, you do not have to disassemble the ceiling.
The last panel is also cut in width, after which the starting profile is put on one side of it. The length of the panel must be cut so that it can be inserted with its ends into the starting profiles without bending. Next, the guide profile is lubricated with “liquid nails” glue, the last panel is installed in place, snapped to the previous one, and the starting profile put on it is glued to the guide profile of the frame.

An example of decorating a toilet with plastic panels with your own hands

Before cutting each panel to the required length, you should check the actual size between the profiles in the location where it will be installed.

Video on the topic

The toilet room, decorated with tiles, looks very beautiful and respectable. But in order to lay it out beautifully, you need to have certain skills in working with such material, and the tile itself will cost a pretty penny. Execute high-quality repairs in the toilet without extra costs And you can do it yourself if you use PVC panels instead of tiles.

Peculiarities

To finish a toilet with plastic panels, you do not need to have any special construction skills or physical strength. This material has a whole range of other qualities that make it easy to handle both during installation work, and during the operation of the finishing made from it.

Although plastic panels are not without their drawbacks.

This lightweight material, which is simply cut and mounted. It can be used to decorate walls and ceilings. PVC panels will hide pipes and other communications that are present in the toilet and often do not look attractive at all, just like the “native” ones. Not smooth walls. But we must take into account that when installed on each side, such a coating “eats” about five centimeters of room space.
It is convenient to decorate a room with this material alone, especially since it is very difficult for two builders to turn around in the cramped space of a toilet room.
If the panels are installed correctly, they will last a very long time (up to twenty-five years) without requiring special care after them. They are resistant to chemicals and it is difficult to damage the coating. It is enough to regularly wipe the PVC walls with a damp cloth so that the toilet does not lose its well-groomed appearance.
The panels are resistant to moisture and temperature changes.
When choosing to decorate a toilet with such panels, you need to take into account that this is a material that melts under the influence of fire, releasing acrid smoke.
If you hit a plastic wall hard, the panel may break.

Style and design

Thanks to such a wide selection, you can decorate a sanitary room in any style. Using panels of different colors, variegated or patterned, a certain visual effect is achieved. So, if you use light panels, this will visually expand the space of the bathroom.

The use of panels with photo printing opens up unlimited possibilities for design. When you enter a toilet decorated with such material, you can find yourself in the atmosphere of an island paradise, among waterfalls, mountains and in any environment that will contribute to peaceful solitude. To create a complete picture, not only the walls, but also the floor and ceiling must be done in a single theme and color scheme. This rule works equally well when designing a separate toilet or a combined bathroom.

Although no one will forbid you to limit yourself to the fact that the panel covers the wall only half or only a quarter, and the other part of the wall is decorated with washable wallpaper or painted water-based paint suitable color.

Dimensions

Having made a choice in favor of plastic panels, you need to take into account that there is no uniform standard for the forms of their release. On sale you can find panels ranging in width from ten to thirty centimeters. Their length can be from two to six meters. The thickness is also different - from eight to twelve millimeters. If the choice is made in favor of sheet panels, then it should be taken into account that their width is both eighty centimeters and reaches two meters. Length from 105 to 405 centimeters.

When calculating the required amount of material, keep in mind that part of it will be used for trimmings. Therefore, it is better to immediately purchase panels with a margin of fifteen percent.

Preparatory work

Before you get to the installation of the panels themselves, you will have to take measurements of the room and buy everything you need for repairs: not only panels, but also profiles for decorating external and internal corners, places where plastic joins the ceiling and floor, for the design of cabinets and doors provided for in your plan. You will need material to create sheathing for future panels. You can choose wooden or metal slats. It must be taken into account that their parameters will determine how much the toilet area will be reduced after all the work is completed. The number of slats depends on the height and width of the walls, as well as the distance between the sheathing elements themselves. If a riser, pipes and a ceiling frame are hidden under the PVC panels, you need to include the material consumption for this when calculating its total quantity.

You may also need dowels and screws. If they are not on the farm, you need to resolve the issue of their availability in advance. Plastic cladding technology also allows for the possibility of gluing panels directly to walls if they are absolutely flat. With this approach to finishing, you will need “liquid nails”. If the plastic will be supported by a wooden sheathing, you will need to purchase a treatment product. wooden structure from rotting. Using a primer for walls and ceilings will prevent mold from appearing under the panels. Insects will not breed under it either.

To properly repair a toilet, you need to carefully prepare its walls for the future. decorative finishing. Remove wallpaper and paint from them. To work you will need a metal spatula. Wallpaper that does not lag behind the wall can be soaked by rolling it over it with a wet roller several times. Don’t be too lazy to completely remove the old wallpaper so that you don’t have to dismantle the plastic panels and carry out the repair again if fungus develops there.

As for the paint, it is enough to remove only what is already peeling off the wall. Sliced required amount elements wooden frame, they are treated with an antiseptic, including the cut sites. Then they need to be allowed to dry. In an apartment building for this a balcony will do. You can also take the workpieces to staircase. While the drying process is not completed, you can treat the walls and ceiling in the toilet itself.

The primer is applied with a long-haired roller. A wide brush will do the job. In inconvenient areas it is narrow. It makes sense to apply a couple of layers of primer, especially since it dries quickly. If you decide to renovate your toilet full program- with the replacement of the toilet - it is better to remove the old one before you start lathing. If pipes and old electrical wiring require replacement, this issue should also be taken care of a little earlier than it comes to external design rooms.

Frame

To make a frame for panel cladding yourself, you need to decide in advance how the PVC panels will be placed relative to the wall - vertically or horizontally. When placing panels vertically, the room will appear higher, while horizontal placement will visually expand it. Wherein " vertical version» involves horizontal placement of sheathing bars and vice versa. When installing slats, you need to rely on the readings of the building level. To fasten the bars to the walls, use self-tapping screws or dowels. Using self-tapping screws, you need to drill holes in the walls and insert plastic caps into them.

By the time of work, the bars must dry well, otherwise they will move later, which can ruin the whole thing. They are attached at a distance of about half a meter from each other. In places where cabinets and shelves will be placed, the sheathing elements need to be placed “more often” so that the fastening is more reliable. The most common option for finishing a toilet is the vertical method of attaching panels. To make a frame for this finish, you first need to install its side posts. To do this, the slats are secured in the corners of the room using self-tapping screws. The vertical strips should not come into contact with the surface of the floor and ceiling.

Then the sheathing is done. The first block is fixed at a distance of two centimeters from the floor. A slatted line is created along the entire perimeter of the room. The same one is mounted under the ceiling. To ensure that the sheathing is uniform, after installing the top and bottom strips of slats, the distance between them is measured with a tape measure and divided in half. Another bar is strengthened in the middle. Each of the resulting sections is also divided into two and the bars are again strengthened at a measured distance. This continues until the distance between the sheathing elements is reduced to half a meter.

To build communication boxes for finishing with panels, use the same materials as to create the frame on the walls. The boxes are attached to the floor and walls. You can connect the bars using self-tapping screws. During the work, it is necessary to provide places for technological holes that will provide access to hidden communications when solving everyday issues. As for the frame itself, you can use not only wooden, but also metal guides for its construction.

If you plan to decorate the toilet ceiling with plastic, the frame on it is created in the same way as on the walls, only the bars are located more closely to each other.

Sheathing

To make wall cladding with your own hands PVC panels, you will first have to install racks on which the decorative strips will be held. When the installation of the frame is completed, you can proceed to the next step, which involves installing racks that need to be nailed to the sheathing. The slats need to be cut at an angle of forty-five degrees. They can be attached to the sheathing with nails or a special stapler at a distance of thirty centimeters from each other.

Plastic panels have grooves and ridges, connecting which together, you can decorate the walls step by step, giving them elegance. Decorative plastic elements in the corners and around the doorway will help cover and hide the joints of the panels. It is better not to neglect the installation of such design components, otherwise the repair will look unfinished.

After installing the panels along the walls, you need to decorate the box around the vertical pipe that runs in the toilet with a decorative layer. To hide communications from view, the panels will need to be cut to length, and in order to cover the inconvenient place aesthetically, finally, install decorative corners where it is needed. To cover the ceiling of a bathroom with panels, you should proceed in the same way as in the case of walls. But during the work you will have to make holes for future lamps and bring out the electrical wires.

In such an important place for an apartment as a toilet, it is not enough to carefully line the walls and go around decorative panels all protrusions, giving the room an elegant and well-groomed look. It is necessary to place hooks, niches and shelves in pre-designated places to make the toilet convenient to use. It is better to designate the places where all this will be attached while the sheathing is going on - then you won’t have to guess where the sheathing bars are placed.

Options for using panels to create hidden niches and shelves can be very different. A person who can manage furniture fittings, it will not be difficult to discreetly cover up with a removable panel something that should not be visible. It is possible, for example, to provide in decorative cladding a window under which the water meter is located, with the ability to close it with a plastic door and easily open it only when required.

Finishing a bathroom with plastic panels usually takes no more than two days, and the results will please you for a long time.

Economy-class renovations with decorating the toilet room with plastic are good to use in a Khrushchev-era building. This is the easiest way to hide an old, unattractive riser from view and make the interior of a small room completely modern and cozy thanks to the right choice of panels: with a pattern or plain ones. For example, red walls in the bathroom may seem too extravagant to some people. Green or blue tone in the company of a pattern, for example, in nautical style will certainly make the decoration comfortable and relaxing.

When renovating a combined bathroom, especially in an old one panel house, you need to carefully consider the issue of ventilation, ensuring free flow of air between the sheathing and the wall, as well as the sheathing and the ceiling. Ventilation grill it also needs to be mounted from plastic, providing it with a decent design. When installing the floor in the toilet, you can do cement screed and lay out the tile covering. It is important that it does not contradict the general color scheme of the updated interior. Even if you want to keep the minimum cost of repairs, you should carefully consider the choice of the decorative coating itself.

The risk of running into a low-quality product today is very high.

To decorate a bathroom, it is better to use panels with additives that increase their flexibility. The material without appropriate additives will be too brittle. It is not difficult to determine how high-quality the panel is in your hands. Plastic good quality can be bent into a ring.
Press the edge of the product with two fingers. The stiffening ribs located inside the high-quality panel cannot be deformed, and there are no dents left on the outside.
The locking strip on the edge should return to its original position when you release it after bending it. In a low-quality product, this plastic strip may break.
Through upper layer the panels should not show through its “insides”.
Use your sense of smell when choosing materials. If the panels are made from low-quality components, they will emit a chemical aroma, which will only become stronger in the confined space of the bathroom. This is not only unpleasant, but also harmful to health.

PVC panels of decent quality must contain additives that prevent the material from catching fire. To make sure of this, request a product certificate from a specialist in trading floor. If you are not provided with documents for the goods, it is better to go to another store.
You should not opt for panels of large width. When it comes to repairs in such a small room as a toilet, this is unprofitable, since during installation there are too many scraps left, which then simply have to be thrown away.
Take the time to inspect each panel you purchase. It is not uncommon for sellers to place defective items in a package of goods. Exchanging them after purchase for a quality product can be very nerve-wracking. You will also have to prove that the panels were not damaged during transportation from the store to your home.

“Extra” time spent in a building materials store will be successfully compensated for by easy and quick installation panels in the toilet, as well as the pleasure with which you can visit this secluded place for many years.

Beautiful examples

The variety of colors of plastic panels opens up great opportunities to implement the most interesting ideas design in accordance with the taste preferences of apartment owners.

Some people consider it worthy to decorate the walls of the toilet room with a stone look, some prefer certain wood patterns, and some prefer abstract patterns that create a feeling of airiness and lightness, or floral patterns present on the panels.

Wall combination beige colour with an unusual pattern and a floor decorated in a red “outfit” will make the toilet room visually very warm. In the eyes of people who especially value warmth, such a design will give the bathroom additional attractiveness. As well as the “neighborhood” of animals and trees on the walls.
Connoisseurs of spring and summer will feel comfortable surrounded by walls with a pattern of branches and leaves. Even on a gloomy winter day, such an environment will bring back spring joy. The light green background helps to set the mood for peace and never gets boring.
The choice of flashy colors in the design of a toilet is a rather rare phenomenon, but there is no doubt that such a design can make an indelible impression on all visitors to a secluded room. No one will ignore the combination of red and black in a room with a special purpose. Elements in the form of red prints on black walls will only enhance the effect, as will the interesting lighting of the ceiling, echoing the design of the floor with white tiles.

Decorating the walls of the toilet with stone would look quite decent. However, in combination with the rich dark gray pattern at the bottom of the panels, this room looks especially presentable and rich.
Using black tones in bathroom decoration only at first glance seems like a risky move. The combination of black walls with white fixtures creates a stylish contrast, making the interior impressive and modern. Energetic and strong-willed people They will clearly appreciate such a neighborhood.

Gray panels under large tiles give the room a detached neutrality and dignified simplicity. Horizontally located narrow and light panels behind the toilet visually expand the cramped space. It no longer puts psychological pressure on the person in it.
Green plastic panels of a soft shade with a thin, graceful line pattern along the perimeter of the toilet room look modest, but with dignity. A harmonious design in a room is created without original techniques, nevertheless makes a great impression.

If you use panels with vertical stripes in blue and pink tones on some walls of the bathroom, you can achieve a cozy effect, since such a pattern resembles the texture of fabric. In this environment you can feel like “under a flannel shirt” or like “under a warm blanket.” If the same pattern is present on the floor, the effect will be even stronger.
In fawn or beige shades of panels, the toilet space looks calm and at the same time lively, especially with the addition of a small floral pattern. Such colors and patterns are chosen by balanced people who look at the world seriously and practically. If the walls decorated with beige panels are dirty, it will be noticeable, but it will not hurt the eye. In addition, such a surface is easy to clean.

PVC panels or, simply put, plastic are much more popular than the same ceramic tile when it comes to design. And, choosing between the same tiles and plastic panels, many are inclined in favor of the latter. What makes this material so attractive? It's simple! The main advantages of PVC panels are their low cost and ease of installation compared to ceramics. If you compare prices, making panels will cost at least 4 times less than laying tiles. Moreover, the water resistance of both materials remains high.

Of course, ceramics are much stronger and more durable, but we must pay tribute - and PVC panels can last a long time if they are treated with care. In addition, they are quite resistant to hot steam or chemicals. Other advantages of the material are as follows.

Easy to install– so that you don’t have to do a lot of work. And you don’t need a lot of tools. In addition, you don’t have to bother with adhesive solutions intended for laying tiles. And you don’t need to have any special skills to carry out the work.
No need to level the walls before finishing. So, if the panels will be mounted on a frame, the base does not need special preparation (at least, it definitely does not need to be leveled).
You can use the toilet immediately after the installation of the panels is completed.. After all, you won’t have to wait for the tile adhesive to dry.
PVC panels can be installed in absolutely any room, but most often they are used to decorate walls in bathrooms, toilets, kitchens, and bathrooms.
Large selection of color variations makes it possible to select panels to suit any interior style. Some panels can imitate wood, stone and other natural materials.
PVC panels for toilet - photo
The panels are very easy to clean. It is enough to dilute soap solution and wipe them with a rag soaked in it.

On a note! Even if you pay for the work of installing the panels by a specialist, rather than doing everything yourself, in any case you will be able to save a lot of money. Panel installation services are much cheaper than the services of a good tiler.

Most panel manufacturers report that the material lasts an average of 25 years. However, in general, this aspect will directly depend on how carefully the owner of the toilet treats the finishing. By the way, during installation, even on the panel frame, very little free space is stolen (no more than 5 cm), so they can be mounted even in narrow and cramped spaces.

Prices for popular finishing wall panels

Wall panels

Disadvantages of PVC panels

There is no ideal material that has no flaws. So PVC panels also have their disadvantages. It is important to know about them before deciding to purchase such material.

Whatever one may say, some of the free space of the panel is still stolen during installation. This is especially true for the frame installation method. If a few centimeters along the walls can play a big role, then it is better to refuse to install panels and choose some other material for finishing.
If the walls are crooked, then it will be impossible to install panels using glue; only the frame method is allowed.
PVC hardly burns, but when melted when exposed to high temperatures, it will emit very acrid smoke, which in the event of a fire can play a cruel joke on the owner of the apartment.
No one is protected from counterfeits, and when buying material you can run into low quality PVC. It can be dangerous to human health. Also, panels of poor quality are not strong and durable.

Despite these disadvantages, PVC panels were and remain one of the most popular materials. And it is unlikely that anything will shake their position in the near future.

Prices for glue different types of glue Kreps

Glue Kreps

Any PVC panel is, in fact, a lining, a plastic board that is very light in weight. The surface of the material is smooth and even, and the panels themselves should not be curved. If you look at the panel from the end, you can see that there are pores in the middle. The planks themselves can have different dimensional parameters.

Table. Parameters of PVC panels.

As for colors, PVC panels can be painted in any shade and are quite capable of simulating a number of natural materials. Their surface can also be either matte or glossy, and there are also mirrored options.

On a note! As for the pattern on the panels, it can be applied in printed form or by gluing thermal film. There are also photo panels that look like previously popular photo wallpapers. And in this case, you can choose absolutely any pattern to decorate the walls.

As for the choice of material, you should follow a number of recommendations in order to purchase truly high-quality and good panels. Unfortunately, fakes and bad material There are a lot of them sold on the market.

Advice! In small rooms it is much more convenient to work using narrow panels. But in spacious rooms you can install wide ones. Narrow ones are generally much easier to install, and there are few scraps left from them. Optimal thickness panels for installation in the toilet is 8 mm.

It is important to understand that high price is not always an indicator of quality. Sometimes the cost of the material can be greatly increased by resellers. You should focus specifically on the manufacturer, that is, the brand, as well as the physical characteristics of the panels.

When purchasing material, you must not forget about the fittings (for example, corners). And it is important to choose the same color and type as the selected panels. As for the slats for the frame or starting profiles, it is important to choose neat and even products.

The process of installing panels on walls (do-it-yourself step-by-step instructions)

Installing the panels is quite simple, and if you have the time and desire, you can do everything yourself and save a lot of money on paying for the services of a specialist. You will need a minimum of tools. This is a level, a cutting tool, a screwdriver, a pencil and tape measure, and a hammer drill.

Step 1. The first step is to carry out small preparatory work. It is necessary to remove all old coating from the walls (tiles, loose paint, etc.). Also, if you plan major renovation, even before installing the PVC panels, it is necessary to replace the water supply and sewerage pipes. Before installing the panels, the walls should be treated with a primer and dried well.

Advice! You immediately need to outline the places where cabinets and shelves will be installed, if they are intended by the designer. This will allow you to arrange places for their attachment - you won’t be able to simply hang furniture on walls with PVC trim. You also need to immediately lay the ceramics on the floor or finish the base with another material.

Step 2. The panels need to be brought into the house and left alone for several hours so that their temperature becomes equal to the ambient temperature. It is impossible to install panels that have just been brought in from the street (especially from the cold). You also need to immediately purchase starting profiles and overhead corners for decoration.

Step 3. It is worth making a box right away for water supply and sewerage. You can make them from metal profile, and then cover it with plasterboard.

Step 4. Now you need to glue the starting profile for the panels onto the sealant. It is glued down along the wall and along the doorway in the corner. In this case, the walls in the toilet are flat, which means that when installing the panels you can do without a frame.

Step 5. Next, you need to measure the height from the floor to the ceiling or to its frame. The result obtained must be transferred to the panel and drawn a straight line with a marker or pencil using a square. By the way, the panel cutting line should be slightly less than the length obtained during the measurement process - about 5 mm. This will make it easier to install the panels.

Step 6. Now you need to cut off the excess panel along the marked line. You can cut PVC with a grinder or stationery knife. Thus, it will be necessary to adjust the height of all panels. If you need to cut the panel to length, then you should cut it with a stationery knife along the edge of the desired honeycomb from the front and back sides.

Prices for angle grinders (grinders)

Angle grinders (grinders)

Step 7 Next, you can install the first panel. It must be entered into the starting profile and be sure to be leveled. The evenness of the rest of the row will depend on how evenly the first panel is installed.

It is important that the panels are installed level

Step 8 The panel needs to be secured. This can be done using a self-tapping screw screwed into the side of the panel, or by placing it on a sealant.

Prices for polyurethane sealant

Polyurethane sealant

Step 10 After the panels are installed on the wall, you need to close their joints with corners placed on the sealant.

Step 11 After completing the installation of the walls, you can begin finishing the ceiling. If it is made using PVC panels, then you need to follow the same principle - gradually attach each panel to a metal profile. True, fixation will be carried out precisely due to self-tapping screws.

If the installation of PVC panels will be carried out on a frame, then the walls must also be prepared, and then the foundations of the frame must be secured to them - wooden slats or metal profile. The starting profiles are then attached to them, and then the panels are installed. You can fasten them to the slats with self-tapping screws or a construction stapler.

Video - Installation of PVC panels on a frame

Video - Installation of PVC panels with glue

Decor and finishing: interesting solutions (photo)

When choosing the design and style of a toilet, it is important to take into account your own wishes and preferences first of all, but you should not neglect the advice experienced craftsmen and designers. First you need to decide on the general color scheme premises and decide which panels to buy - patterned or plain, glossy or matte, etc. Here it is worth starting from the general design concept in the apartment.

If the toilet has a small area, then you should choose plain light panels. Although in some cases the drawing may look quite organic and will not steal free space. You can also combine panels with each other various colors, as well as strips with images or plain ones.

The marine style, which was once popular in bathrooms, bathrooms and toilets, is now far from the only option for decorating these rooms. Sometimes panels that look like stone or imitate jungle, etc. look very cool. And sometimes it’s worth sticking with the black and white classics.

On a note! Wood-effect panels do not always look good in a toilet, but much will depend on the overall design concept, as well as directly on the shade of the panels. Sometimes such toilets turn out to be quite cozy and visually warm.

If you don’t have your own ideas, then on the Internet you can find a lot of interesting options for decorating toilet walls with panels. Some of them may be to your liking, and they can be implemented in your own restroom. If you want to do something unique, but your imagination is tight, then you can take some kind of ready-made option, looking at the photos, and bring it to life, slightly modifying it or remaking it for yourself.

Panels are a great way to decorate a bathroom or toilet beautifully and inexpensively. Moreover, it can look stylish and expensive. The main thing is to choose the right color of the material and perform the finishing work properly. Several ideas for decorating a toilet with PVC panels can be found in this material higher.

To connect plumbing fixtures to the water supply network, a flexible water supply is used. It is in demand when connecting faucets, showers, toilets and other water intake points, and significantly simplifies the installation process. Flexible liner is also used during installation gas equipment. It differs from similar water devices in its manufacturing technology and special requirements security.

Characteristics and types

The flexible hose for connecting plumbing is a hose of different lengths made of non-toxic synthetic rubber. Thanks to the elasticity and softness of the material, it easily takes the desired position and allows installation in hard to reach places. To protect the flexible hose, there is an upper reinforcing layer in the form of a braid, which is made from the following materials:

Aluminum. Such models can withstand no more than +80 °C and retain functionality for 3 years. At high humidity Aluminum braiding is prone to rust.
Of stainless steel. Thanks to this reinforcing layer, the service life of the flexible water line is at least 10 years, and Maximum temperature transported medium - +95 °C.
Nylon. This braid is used for the manufacture of reinforced models that can withstand temperatures up to +110 °C and are designed for intensive use for 15 years.

The fasteners used are nut-nut and nut-fitting pairs, which are made of brass or of stainless steel. Devices with different permissible temperatures differ in the color of the braid. Blue ones are used for connecting to a pipeline with cold water, and red ones - with hot ones.

When choosing a water line, you need to pay attention to its elasticity, reliability of fasteners and purpose. It is also mandatory to have a certificate that prevents the rubber from releasing toxic components during operation.

Features of gas connections

When connected gas stoves, speakers and other types of equipment also use flexible hoses. Unlike models for water, they have yellow and are not tested for environmental safety. For fixation, end steel or aluminum reinforcement is used. There are the following types of devices for connecting gas appliances:

PVC hoses reinforced with polyester thread;
made of synthetic rubber with stainless steel braid;
bellows, made in the form of a corrugated stainless steel tube.

The Santekhkomplekt holding offers engineering equipment, fittings, plumbing fixtures and devices for connecting them to communications. The assortment is represented by products and materials from well-known foreign and domestic manufacturers. Discounts apply for bulk purchases, and product quality is confirmed by standard certificates. For information support and assistance, each client is assigned a personal manager. The ability to arrange delivery within Moscow and to other regions of the Russian Federation allows you to quickly receive the purchased goods without unnecessary hassle.

Drainage is a drainage and drainage measure to remove excess groundwater.

If water does not leave the site for a long time, the soil becomes gleyed, if shrubs and trees quickly disappear (get wet), you need to urgently take action and drain the site.

Causes of soil waterlogging

There are several reasons for soil waterlogging:

clay heavy soil structure with poor water permeability;
aquifer in the form of gray-green and red-brown clays is located close to the surface;
high groundwater table;
technogenic factors (construction of roads, pipelines, various objects) that interfere with natural drainage;
disruption of the water balance by the construction of irrigation systems;
The landscape area is located in a lowland, ravine, or hollow. In this case, precipitation and the influx of water from higher places play a big role.

What are the consequences of excess moisture in the soil?

You can see the results of this phenomenon yourself - trees and shrubs die. Why is this happening?

the oxygen content in the soil decreases and the content increases carbon dioxide, which leads to disruption of air exchange processes, water regime and nutrition regime in the soil;
oxygen starvation of the root-forming layer occurs, which leads to the death of plant roots;
the supply of macro and microelements by plants (nitrogen, phosphorus, potassium, etc.) is disrupted, because excess water washes out mobile forms of elements from the soil, and they become unavailable for absorption;
intensive breakdown of proteins occurs and, accordingly, the processes of decay are activated.

Plants can tell you at what level groundwater lies

Take a close look at the flora of your area. The species inhabiting it will tell you at what depth the groundwater layers are located:

perched water - it is best to dig a reservoir in this place;
at a depth of up to 0.5 m - marigold, horsetails, varieties of sedges grow - bladderwrack, holly, foxweed, Langsdorff's reed;
at a depth of 0.5 m to 1 m - meadowsweet, canary grass, ;
from 1 m to 1.5 m – favorable conditions for meadow fescue, bluegrass, mouse peas, rank;
from 1.5 m - wheatgrass, clover, wormwood, plantain.

What is important to know when planning site drainage

Each group of plants has its own moisture needs:

at a groundwater depth of 0.5 to 1 m they can grow on raised beds vegetables and annual flowers;
water depth up to 1.5 m is well tolerated vegetable crops, cereals, annuals and perennials (flowers), ornamental and fruit and berry bushes, trees on a dwarf rootstock;
if the groundwater is more than 2 m deep, fruit trees can be grown;
The optimal depth of groundwater for agriculture is from 3.5 m.

Is site drainage necessary?

Record your observations for at least some time. You yourself can understand how much drainage is needed.

Maybe it makes sense to simply redirect melt and sediment water along the bypass channel, rather than allowing it to flow through your site?

Perhaps it is necessary to design and equip a storm drain and improve the composition of the soil and this will be enough?

Or is it worth doing drainage system only for fruit and ornamental trees?

A specialist will give you the exact answer, and we strongly recommend calling him. But after reading this article, you will gain some awareness on this issue.

Upon completion of technological and production tasks related to the arrangement of a sewer system in an apartment building, industrial building, and also in private households it is required to test the involved system using the forced flow method. This task is used to identify possible defects or improper installation of the entire involved sewerage part, and the test report for internal sewerage and drainage systems will be material evidence of the work on acceptance of the facility.

A visual inspection should be accompanied by inclusion in the test report of internal sewerage and drainage systems according to SNIP, which is currently represented by the current regulations of the “D” series appendix, which corresponds to SP 73.13330.2012 “Internal sanitary systems of a building”, recently a new one has been applied updated working edition according to SNiP 3.05.01-85.

Repairing a toilet with plastic panels is best option for those who want to make budget renovations in their apartment. This method has several advantages. Firstly, you can purchase sufficient quantity inexpensive material. Secondly, it is very easy to install it yourself, which will save a lot of money on paying the craftsmen.

Plastic panels - features of choosing a reliable material

Before finishing the toilet, you need to choose quality panels. There is a huge range of these products on the market, but not all products meet the requirements of modern quality standards. It can be quite difficult for a buyer to visually determine the reliability and safety of the products offered. To prevent you from running into defective panels, we will tell you a few secrets. They will allow you to choose really high-quality material that will last for a long time.

PVC panels must contain additives designed to improve the elasticity of the material. Thanks to the presence of these components, the products are easily bent and are difficult to accidentally mechanical damage. If you are offered plastic that leaves dents when pressed with your finger, then you should refuse such products. This material is not capable of lasting long time. In addition, within a year it will lose its original appearance.

To easily check the quality of the material, you should do the following. To begin, grab the edge of the panel with two fingers and lightly squeeze the product. As a result, the ribs that are inside should not be deformed or bent. In addition, no dents are allowed at the top or bottom of the panel. Then try to bend back the mounting strip of material. It is located on the edge of the product and forms a docking lock. As a result, this part of the material should not break or crack. In high-quality materials, it quickly returns to its previous position, and no traces remain on the bend lines.

To check, place the panel against your nose. The product should not emit any unpleasant odors. If you smell a strong chemical smell, it is better not to use such material for. Most likely, this plastic was created from cheap raw materials or with violations of technological production standards. If you buy these panels, the toilet finished with them will have an unpleasant odor and hazardous fumes.

In stores you can find panels of various widths. In small rooms, it is worth using products that are not too wide, since after work there will be a large amount of unusable waste. Therefore, in order not to guess with the desired batch of finishing, before making it, it is worth measuring them and calculating the required amount of material. Another important nuance when choosing a product, it is the presence of a certificate from the seller. The document must indicate the country of origin and the product’s compliance with all sanitary and technical standards.

How to buy material and take the necessary measurements?

To finish the toilet with plastic panels yourself without any problems, you need to prepare for the work. First of all, take all measurements and buy materials. Preparation of tools and surface treatment will also be a mandatory activity. The purpose of taking measurements is to find out how many panels will be needed for the job. At the same time, it is also important to count the number of profiles that will be useful for decorating external and internal corners. In addition, profiles will be needed to mount the panels to the floor and ceiling lines. Often these finishing elements are needed to install doors, windows and cabinets, if such work is also included in the planned renovation.

The choice of profiles directly depends on design idea, the size of the toilet and the technique of installing panels in some areas of the room. As for the base material, its quantity should be 15% more than the measurement result. A certain part will go to trimmings. Cases of improper cutting or accidental damage to the panels should not be ruled out.

Remember that you will also need material to install the sheathing. In most cases, homeowners need to save every centimeter of the apartment, so the toilet has a small area. In this regard, wooden slats or metal profiles with a cross section of 50x20 mm are suitable as a frame. To calculate the number of slats, you need to take into account that the guide battens will be located at a distance of 50–60 cm from each other. In addition, calculate the number of parts for the sheathing of the ceiling frame and the decorative box that will hide the pipes. But this is only if you plan to finish these areas of the toilet.

In order to secure the frame to the wall surface, you need to purchase dowels of such length that they can be screwed into the wall by 40–50 mm. To find out the number of fasteners, take into account that their pitch during installation will be 40–45 cm. To fix the panels to the frame, you need to purchase self-tapping screws no more than 20 mm long. If wooden slats are used as lathing, then for fixation it is better to use staples 10 mm long. If your toilet has perfectly smooth walls, then you don’t have to do the sheathing. In such situations, plastic panels are glued directly to the walls liquid nails or tile adhesive.

Preparing the room - how to level the walls before finishing?

As with other types of renovation work, finishing a bathroom with plastic panels requires necessary tools. Having them at hand, you will not be distracted by searching for the necessary equipment. To work you will need:

screwdriver and a set of bits for it;
electric drill or hammer drill;
drills of different diameters;
manual or electric jigsaw;
scissors for working with metal, if a metal profile is used;
stationery knife;
hammer;
square and tape measure;
marker or pencil;
stapler and building level.

To prepare the wall surfaces, you will also need construction hair dryer, spatulas, brush and roller for priming. Special attention worth your time construction level. It must have a horizontal and vertical pointer. This tool will help to achieve the most even surface of the walls in the toilet. If you are going to specifically buy both a drill and a hammer drill, then you can get by with only one drill. It is important that it has a perforation function. Such a tool will cost a little more than a regular one, but you will save money on purchasing a separate hammer drill.

To level the walls in the toilet, you first need to remove all the old finish. This will help prevent mold and mildew from appearing in the space between. To remove old wallpaper or other types of trim, use a metal putty knife. If you need to clean the walls of worn wallpaper, but it has already firmly adhered to the surface, then you can apply it several times to the old finish for cleaning. hot water using a roller for this. You need to remove the material in those places where it has begun to separate from the wall. If the walls in the toilet were previously painted with paint, then it is not necessary to completely remove it from the surface before repairing. The main thing is to remove the dried compound where it has begun to flake off.

After cleaning the surfaces on the walls, make markings. This is necessary in order to determine the size and number of slats for the sheathing. If you chose wooden slats as the last option, then at the next stage prepare them for installation. First, they are cut to size, after which they are impregnated with an antiseptic composition. It is best to do this on the balcony or in any other room where there is a draft. While the slats are still wet, you can apply a primer to the walls and ceiling of the toilet. It is best to apply 2 layers of this composition. If you use a white primer, then marking the walls should be done only after the material has dried on the surface.

Making lathing - an option for uneven surfaces

Finishing the toilet with PVC panels is one of the last stages indoor renovation. First of all, you will need to secure the batten guides. This should only be done on dry, smooth walls. Before installation, drill holes in the slats, the diameter of which will correspond to the diameters of the dowels. After this, the slats are applied to the markings. You need to insert a drill into each of the holes in the rail and mark the drilling locations in the wall. Then the lath is set aside, and the place marked in the wall is drilled to the length of the dowel.

To secure the strip, it must be attached again to the marking so that the holes in it and the wall coincide. After this, we take dowels with screws screwed in and drive them into the walls one by one through wooden guides. All elements of the sheathing are installed in a similar way.

Before covering the walls in the toilet with plastic panels, you need to make a decorative box. It is made of a metal profile and serves as a place where pipes and other communications will be hidden. To make the structure, install vertical racks under the ceiling so that they are located on the sides of sewer riser. After that vertical elements fastened with horizontal guides. To hide all the pipes, the frame of the box must run along the sides of the communications so that after installing the panels they are not visible.

Installation of panels - how to cover walls with plastic yourself?

Next we proceed to finishing the walls. The best place to start is from far corner. All vertical panels that are installed to repair a toilet must be leveled using a level. Only after this can they be screwed on. Remember that the correct position of the first panel determines how smoothly the other products will be screwed on!

If one or more walls in your toilet are perfectly flat, then there is no point in installing lathing on them. In such a situation, it is better to glue the panels directly to the surface. To do this, take liquid nails and apply them thin layer for covering walls. After this we apply plastic lining and, until the glue has dried, we align each of the panels. After finishing the walls, carefully install the material on the decorative box. To do this, take the first panel and attach it to the frame. We mark the cutting places and shorten the product along the indicated lines.

Next, we fasten the paneling with self-tapping screws and repeat the procedure with the rest of the material. In corners and joints, use special ones that will make the finish more neat. If finishing your toilet with plastic involves installing the material on the ceiling, then do not forget to make holes in the panels for the lights. If you use spotlights, then you need to cut out circles whose diameter will be the same as the diameter of the lamps. If you have a small lampshade, then the hole should be of such a size that you can insert the wires needed to connect the light bulb into it.