How to make your own hand drill for excavation work. Do-it-yourself drill: earthen drill, for poles, wells, drawings, dimensions Do-it-yourself hand drill for poles

Reading time ≈ 10 minutes

Residents of the private sector are very familiar with situations when something needs to be built or installed, but the base of such a structure will be in the ground. In this regard, many are wondering how to make a drill for drilling holes for pillars (piles) with their own hands, using materials that may be available in household. In addition, without excessive modesty, it can be argued that in some cases, self-made instruments exceed the quality of factory products. The thing is that a standard is produced at the factory, and at home you can adapt such a device to specific needs, taking into account the condition of the soil.

Homemade hand garden auger

Dependence of design on purpose

For household needs, you can make a hand drill with your own hands for various purposes, although in any case, such a tool is intended for drilling holes. But at the same time they are distinguished by appearance And operational characteristics, This:

  • ordinary garden auger;
  • auger garden auger;
  • drill for TISE piles (Technology of Individual Construction and Ecology).

To assemble such a tool, you will definitely need a welding machine operating on alternating or direct current.

Common garden auger

Earth garden auger

To make an ordinary garden auger, which is most often used for not very deep holes, you need a powerful rod, made of solid (scrap) or hollow pipe profile. In addition, you will need semicircular cutting discs welded at a certain angle of attack (it is best if it is alloy steel). Using this tool, holes are made for planting plants (usually seedlings of shrubs or trees), as well as holes for installing fence posts or other light architectural structures.

Homemade auger hand drill

The word "auger" with German language(“Schnecke”) is translated as “snail” and this perfectly characterizes the configuration of the cutting device. The blades are arranged like a right-hand thread with a large pitch, which allows you to pull the drill out of the ground much less frequently, since the soil rises to full height blades without interfering with drilling. The functionality of such a tool is practically no different from the device described above, but labor productivity in this case almost doubles. If, for example, you build a fence around the perimeter of the site, you will have to install a lot of supports, so speed will only bring benefits. Certainly. It is better to use an automated drive for the auger.

Homemade drill for TISE piles

This tool is used to make wells with expansion at the bottom

The TISE pile drill fully complies with the technology individual construction and ecology of work, and in domestic conditions, as a rule, it is used for pouring pillars with an expanded base under. Its uniqueness lies in the fact that near the cutting blades there is a folding blade (knife), with the help of which an expansion is formed. If we talk about labor productivity when pouring such foundations, then such tools are simply irreplaceable.

Making an ordinary garden auger at home

Below we will look at how you can make such a design at home, provided that you have a workshop (for many car enthusiasts this is a garage).

Components

The constituent elements from which the entire assembly is made

List of elements:

  • The cutting parts are two semicircles made of alloy steel, with sharpened edges. Depending on the purpose of the tool, its diameter is also determined. In some cases, semicircular blades are fixed with a bolted connection so that they can be replaced with a different diameter.
  • The rod is a round or square pipe profile, although sometimes such a part is made from scrap, but this significantly increases the mass and complicates the work process. The length of the rod depends on the need, but most often it is made for pits 50-80 cm long and up to 1.5 m (if this parameter is reduced, you have to constantly work in a bent position). But if one and a half meters is not enough (the depth of the hole is 80-100 cm or more), then it is better to make a prefabricated rod with extendable rods (they can be joined using a nipple).
  • The crossbar for the handle is welded to the top of the rod in the shape of the letter T, where the optimal length of the crossbar is 25-30 cm in each direction. If you make these levers shorter, then scrolling will be much harder.
  • The tip is made sharp; it serves as a drill, which centers the blades in relation to the surface of the earth. That is, they will not move to the side, since they are a single unit with the drill.

What materials will you need?

Square pipe profile

To make a rod, as mentioned above, a square or square pipe profile is suitable round section. If the wall of such a profile has a thickness of 2-2.5 mm, then a section of 20×20 mm or ø20 mm is suitable, but if the walls are thinner, then the section should be increased to 30×30 or 35×35 mm, ø30-35 mm. In the event that during work there may be a need to screw on an additional rod, then only a round pipe profile is suitable for the rod.

Flat tip in the form of a lance with central and side sharpening

A sharp tip must be welded to the end of the rod, which can be made from a piece of a thick drill with Pobedit soldering– they are used for drilling concrete with a hammer drill. But you can also make such a point from thick reinforcement or a piece of steel, sharpening it in the form of a flat peak, as in the top photo.

The cutting part is made of a disk for manual circular saw

The most crucial moment is the manufacture of cutting blades and they can be made from:

  1. sheet steel 3-4 mm thick;
  2. saw blade from a grinder (diamond) or a hand-held circular saw.

In this case, it is most convenient to use discs from a diamond-coated grinder, designed for cutting concrete, or from a hand-held circular saw. When the diamond coating is applied, a thin strip of no more than 1 mm remains around the circumference and it is easy to grind it off, making the edges sharp, and the toothed disk from the circular saw can only be cut in half.

For reference. The internal diameter of the disk or mounting hole is standard 22.5 mm.

And a few more words about the handle - it should be from round pipe and under no circumstances should you put any plastic on it, much less wrap it with electrical tape.

Method of fastening knives

Removable bolt-on blades

If it is planned to drill wells of different diameters, then the blades on the tool can be made of a removable type. For this purpose, two shelves are welded to the rod and knives are bolted to them, as shown in the top photo.

The optimal angle of attack is 30-40⁰

If you are not going to change the diameter of the blades, then most best option, this is ø120 mm and for this purpose a saw or trimming disk ø125 mm (5 mm width of diamond coating and it will no longer be) is best suited, which needs to be cut into two semicircles. Seatø22.5 mm will have to be adjusted to the rod, cutting off the excess using electric welding. For soft soils, the angle of attack is usually 30⁰, and sometimes even 40⁰, but for hard soils it is better to lower it to 22-25⁰.

Components of a garden auger: 1) rod with a point, 2) cutting discs, 3) handle for rotation

Here is a drawing of a homemade garden auger with ø120 mm blades (according to the diameter of the used cutting disc on concrete with diamond coating). Below is a video on how to make such a tool:


Video: Do-it-yourself garden drill in a home workshop

Auger drill

Schematic diagram of the manufacture of an auger drill

Now let's figure out how to make an auger drill for drilling holes for pillars with our own hands. Such a tool does not have to be removed from the hole every 5-10 cm of passage, since the soil dump moves during rotation to the upper blades of the auger. This significantly speeds up the process, but working with it requires a lot of physical strength, so in most cases such installations are used in conjunction with an automated drive.

All disks are clamped in a vice and the same sector is cut out for rotation

Now the most crucial moment: you need to cut out a trapezoidal sector from all the disks folded together, although these inclined ones will intersect in the center, forming an acute angle. The bottom line is that when turning each upper disk, the left edge of the cut sector should coincide with the right edge of the lower one. It is, of course, better to first do such things on paper and if everything matches, transfer the markings for cutting to the metal. The number of screw turns will correspond to the number of disks.

Attention! Do not lose sight of the fact that for docking the lower disk uses the right side of the sector, and the upper one the left. If you do the opposite, you will have to drill counterclockwise.

Now the welding work begins:

  1. place a disk on a plane, and place another one on top of it, but so as to overlap the cut sector, that is, the left edge of the upper one should adjoin the right edge of the lower one;
  2. this joint is welded by electric welding and the next disc is placed on top, acting on the same principle;
  3. This is how all the disks are joined and welded, making a compressed spring out of them.

The compressed spring is stretched using a winch

Finishing welding work, this homemade spring needs to be stretched to form an auger. To do this, the assembly is put on a rod and the lower disk is welded at the desired angle, for example, 30⁰, and something like a ring can be welded to the upper disk so that it hooks onto the winch hook. The rod is fixed on the floor (figure out how to do this yourself - circumstances vary) and the spring is stretched with a winch, after which the upper disk is welded. The rod is released and the entire structure is scalded in a spiral.


Video: Making an auger drill

Drill for TISE piles

Operating principle of the TISE pile drill

The drawing above shows the principle of operation of the TISE pile drill: first it makes a shaft required diameter, and at the bottom the well is expanded using a folding knife. But perhaps I will disappoint you, since in order to make such a design at home, you need, at a minimum, a workshop with tools and professional mechanic skills. To consider such a build, you will have to post a separate article, even a small one, but here we will limit ourselves to showing a video on self-assembly Borax TISE:


Video: Homemade drill for TISE piles at home

Conclusion

From this material you learned how to make a drill for drilling holes for poles with your own hands. You won’t use a drill for TISE piles to install a fence or build a foundation, so for a house an ordinary drill or, if you have something to make a drive from, an auger drill is quite enough.

The pillar is the main architectural element of many types of fences and buildings. To install it you need special tool, hand drill for poles. With its help, holes are selected in the ground into which the pillars are installed.

If necessary, motorized drills are used to make a large number of holes, but in private construction, in particular, during self-construction fences, manual versions of such a tool are used. There are a lot of industrially produced models, but nothing prevents you from making your own drill that will satisfy local needs. And it will cost less than store-bought.

At least minimal skills in working with welding machine and its presence.

Alternative option– production of custom-made tools according to the selected project. In this case, you will need to find performers and a suitable drawing.

Construction of an earth drill

Fundamentally, each drill consists of three main elements:

  1. Pike, which plunges into the ground first and centers the entire tool during the first stages of drilling. Some versions of auger drills and designs with an earth receiver are not equipped with a lance.
  2. Cutting part, made in the form of a screw, half disks or having another configuration.
  3. Solid or segmented rod, to the bottom of which the working elements are attached, and to the top - a handle or pin for connection to the motorized unit.

The different types and combinations of these elements make the difference between drill types. The garden auger is equipped with a peak and two blades, mounted on the main rod at a certain angle (usually 35-40 degrees to the perpendicular to the axis). This is not the most productive tool used for making planting holes or holes for small supports.

Auger drill– a specific option for quickly installing wells for fencing supports. It is equipped with a spiral blade with several turns for removing soil, which is cut by a blade at the bottom of the auger.

The cutting edge of the blade should always remain the lowest point of the auger. Otherwise, the device will not be able to drill into the ground. Therefore, models with two to four semicircular blades are suitable only for making shallow holes for planting plants. The soil is directly cut by only one corner of one blade.

Drill with earth receiver It is a piece of large-diameter pipe, in the lower inner part of which blades are fixed, most often equipped with teeth. As the drill rotates, they fill the volume of the pipe above them, after which the tool is removed from the ground.

Drill for TISE piles is a tool of the previous type, equipped with a hinged blade for creating channel extensions for pouring pile foundations. Sometimes, instead of a cutting part, the earth receiver is equipped with a blind bottom for collecting soil selected by a folding blade.

Making a drill

The main tools for self-made The drill is used by an angle grinder and a welding machine. The process begins with the selection and preparation of the main axis of the tool. A round (26.8-48 mm in diameter) or profile (20×20-35×35) pipe is suitable for this role.

You cannot make a garden auger from a profile square pipe with your own hands. For it, exclusively pipes with a round cross-section are used.

The required length is calculated by adding 50-60 cm to the depth of the future well. If the final value exceeds one and a half meters, you will need to make the bar collapsible. The connection mechanism can be any (threaded, cotter pin, or other), the main thing is that it can withstand the loads during rotation with resistance.

The pike is usually made separately. From a piece of pipe, inner diameter which is equal to the outer one, you can simply make a sharp tip or flatten the pipe, and then roll it into a spiral of one or two turns or sharpen it in the manner of the tip of a wood drill. Other options include soldering a narrow spiral screw. Good results shows the use of a forty-diameter wood drill. In this case, the diameter of the end drill must exceed the outer diameter of the rod.

After the lance is welded to the axial rod (or its lower segment), you can begin constructing the main cutting part. To do this, an old saw blade from a circular saw, the diameter of which corresponds to the parameters of the required hole, is cut into two equal halves. The resulting blades are welded to the main rod above the peak. The preferred angle to the perpendicular to the axis is 30-40 degrees, to the vertical - strictly 90. The cutting edges are sharpened.

Another, more productive option is to make a screw. For it, circles are cut from sheet iron, the diameter of which corresponds to the parameters of the required recess. The number of disks is equal to the number of turns of the future spiral (at least three). The blanks are stacked, after which a hole is drilled in their center, commensurate with the outer diameter of the pipe.

Afterwards, a small segment is cut out of the disks. The resulting parts must be welded to form a spring. Then it is stretched on a winch, the seams between the turns are welded with reverse side and attached to the axle.

The final touch is the handle. It is made from a piece of the same pipe that was used for the axial rod or a diameter more suitable for the hand. The mounting method depends on personal preference. The handle can be welded to the axle, reinforced with additional crossbars, or made removable.

Materials used

Depending on the type of drill being manufactured, they are used various materials, but the basis is always round or profile pipes and sheet metal (waste saw blades).

Pieces of pipe, parts of broken wood drills, and metal plates are used as pikes. Or models are made without peaks. Studs and nuts are used to connect the rod segments.

In general, the range of necessary and acceptable materials depends on the chosen design. It must be thought through before starting work.

Cutting elements and their fastening

The cutting part of earth drills can be removable or non-removable. However, detachable mounting is only permissible on versions with half blades or saw blades or sheet metal. To do this, shelves are attached to the main rod, located at the same angle as the blades. 2-3 holes are drilled in the shelves, to which the cutting parts are attached using bolts and nuts.

Replacement bits can also be made for drills with an earth receiver. To do this, in the reinforcing arc that attaches the bucket to the rod, it is necessary to make a flattening, drill a hole and cut a thread in it.

The screw cutting parts are rigidly attached to the axis. To drill holes of different diameters, it makes sense to make several attachments for one handle.

Some modifications

  1. Straight crushing blades between the lance and the cutting edge.
  2. Multi-tier arrangement of blades with gradually increasing diameter.
  3. Power ribs between the corners of the blades and/or the axial rod.
  4. Receiver box to remove more soil in one go.
  5. Additional blade with 2-3 teeth for easier drilling in dense soils.
  6. Removable blades for quick replacement during work.
  7. And many others, the number of which is limited only by personal ingenuity.

Video

Drill for TISE piles

The fundamental difference between a drill for a device pile foundations consists in the presence of a folding blade and a container - a land receiver. It is often manufactured as a separate tool along with an auger drill for the actual wells.

The blade folding mechanism is a rod that moves a small piece of pipe larger diameter, put on the main rod. This movement activates a system of levers that lowers the blade.

Auger drill

To make multiple holes, it is better to use an auger drill. For one-time projects, a fishing ice pick is quite suitable. But for the mass installation of holes, it is better to purchase or make an appropriate drill from pipes and other materials.

In a “working” auger drill, only one edge of the blades protrudes. The second can be equipped with a comb with several teeth located slightly below the cutting plane.

If you have the time and money, using a motorized block and a special bed will help significantly speed up drilling holes for fence posts.

Blueprints

The abundance of designs allows you to create a highly specialized tool for personal needs. Let's look at some drawings of such options.

Shovel drill

When planting plants, the drilling depth is not critical. Therefore, you can donate an old shovel to make hole preparation easier. You should retreat 30 mm from the lower center point. Draw lines from it to the edges at an angle of 10-20 degrees. Then step back 30 mm from each edge and draw vertical lines. The bayonet segments located between the verticals and lines diverging from the center are cut out.

Then cut the marked 30mm from the bottom center point. Now all that remains is to bend the lower and side parts of the bayonet in opposite directions along the marked lines. The earth drill with your own hands is ready.

How to make homemade drill for fence posts

Owners of household plots or summer cottages often faced with the need to dig a deep narrow hole to install posts, for example, for a new fence, gazebo, supports for a vertical garden, flower bed, grape trellises or arches, etc.

Such narrow holes and wells sometimes need to be made in the most inconvenient places. And such holes, especially deep ones, cannot be dug simply with a shovel; here you need special device- drill.

Advantages of this device

Garden earth drill- This tool for drilling wells in soil, which is simply necessary in a summer resident’s household. It is convenient and easy to operate, helps reduce to a minimum the effort and time spent on solving the above problems, it is very versatile: with interchangeable blades of different diameters and configurations, its functions can be significantly expanded. This tool can replace several diggers armed with shovels.

To dig a hole with its help, you just need to place it at the intended place and, applying slight pressure, make rotational movements. To make it easier to imagine what a garden drill looks like, remember what a regular kitchen corkscrew looks like. And the principle of its operation is similar to the principle of operation of a corkscrew.

Therefore, working with a drill does not require special training or physical strength; even a teenager, woman or elderly person can work with it.

This tool is quite light and compact, which allows you to effortlessly carry it from place to place and perform work with it in hard to reach places on small spaces. Finally, it is worth noting the clear advantages of the drill when working on difficult soil. A drill made of hard metals is capable of cutting roots and splitting small stones that are found at depth.

Functionality

Now let's talk about the capabilities of this tool. Let's consider the option the simplest model drill for soil with average density and with average physical capabilities of the worker. Under such conditions, a hole 1 m deep and 20 cm in diameter will be made in approximately 15 minutes. A well with a depth of 3 m and a diameter of 30 cm under the same conditions will take about 2-3 hours.

The maximum possible depth for the best models of this tool is 15 m. Validity period is at least 10 years (approximately 300 wells).

Types of drills

Garden augers differ from each other in the type of cutting part. Cutting elements are in the form of a screw, helical(like in a tailspin) and in the form of semi-discs, two-blade(a kind of flat cutter). Cutting parts are removable and welded, they can be multi-tiered. Sometimes the drill starts with smaller diameter blades and gradually increases.

But all this applies to drills made in production conditions. They can be purchased in special stores. And although their cost is generally affordable (on average about 1.5 thousand rubles), these costs are sometimes not very useful. It should also be noted that factory-made drills do not always meet the requirements of the specific area being processed. The tool may not be designed for sufficient depth, or its attachments may not fit the required hole diameter.

Self-production

In addition to being easy to operate, a garden auger is also quite simple to make at home. For an owner who is familiar with plumbing tools and knows how to use them, making it is not difficult. In this article we will try to give recommendations on the manufacture of both the simplest drill and more advanced models. This will help you save on purchasing tools.

Let's start with something simple. For homemade The most suitable design is with a cutting part in the form of two semi-disks, blades or one disk - a flat cutter.

First of all, you need to make a drawing of the chosen structure, taking into account the size of the expected depression in the ground, its diameter and depth. Wherein the diameter of the cutting element should be 5-7 mm larger than the future hole.

Materials

It is necessary to prepare materials, namely:

  • a piece of durable sheet metal for making a cutter (blade),
  • a piece of pipe for the wrench of suitable length,
  • a piece of pipe of smaller diameter (so that it is inserted into the first pipe) for making an extension pipe,
  • a piece of metal rod for the handle,
  • threaded rod with wings,
  • 4 bolts with washers and nuts.

Tools

You will need:

  • welding machine,
  • Bulgarian,
  • hammer,
  • electric drill with a set of metal drills,
  • abrasive wheel for sharpening cutting elements,
  • standard set of locksmith tools.

Manufacturing process

  1. Draw a circle of the required diameter on a piece of sheet metal and mark its center. Using a grinder, cut out the blank for the future blade. Then apply a cutting line to the workpiece (along the diameter line) and a cutout along the circumference of the knob. Having cut the resulting disk in half along the diametrical line, we use a grinder to make cutouts for the knob on each half.
  2. Take a blank pipe for making a wrench and use a grinder to make longitudinal cuts 3-4 cm long at one of its ends. There should be at least four of them. Then, using a hammer, bend the cuts towards the center of the pipe so that a kind of point is formed. Now it needs to be scalded with a welding machine so that earth does not pack into the pipe-knob.
  3. The next stage is welding both halves of the disk to the collar. It should be welded at a distance of approximately 5 cm from each other at an angle to the plane of rotation of approximately 20 degrees. Now one part of the drill is ready.
  4. Weld the handle perpendicularly to the extension pipe: you will get a part in the shape of the letter “T”. For strength, the handle can be additionally reinforced with a metal “kerchief”. Insert this T-shaped part into the pipe-collar and, after drilling through hole, connect both parts with a pin with wings. There can be several such holes in the extension pipe to adjust the overall length of the knob as needed.
  5. The drill is ready. All that remains is to sharpen the blades. It is important to take into account that the cutting edge on the cutters is sharpened so that the tip faces the bottom, towards the bottom of the future pit.

On next video This process is clearly shown:

How can you improve the tool?

  • First, you can make a drill with replaceable cutters. Then with its help it will be possible to drill wells of various diameters. To do this, it is necessary not only to make spare cutters of appropriate sizes, but also to provide a method for attaching replacement blades to the driver. The simplest method of fastening can be two welded plates of the same sheet metal, which will serve as mounting platforms for the blades. They should also be welded at an angle of 20 degrees to the plane of rotation. In the blades and in the mounting plates, you need to drill holes for bolts, 2 on each plate and, accordingly, on each blade. The cutters are fastened with ordinary bolts (M6) with washers and nuts. Please note that the bolts must be inserted with the threads facing up so that they do not interfere with the drilling process.
  • Secondly, it is possible to make the lower end of the knob sharper, and therefore more functional. To do this, cut out a narrow plate from sheet metal about 10 cm long and about 2 cm wide. Turn it on one side with a grinder into a cone, making it in the form of a point. Instead of making cuts at the end of the knob, you just need to flatten this end, after inserting a turned plate there and scald it with a welding machine. You will get something like a peak. Another option for such a peak is to make the plate slightly longer (15-17 cm) and, after heating it, roll it up like a small screw (remember, again, a corkscrew). For the rest, proceed as in the first option. Some craftsmen thought of welding a drill of the appropriate diameter for working on wood or metal as such an auger. This greatly simplifies the drilling process. The drill itself goes into the ground like clockwork.
  • Thirdly, (this is suitable for especially dense deep layers of soil) you can weld a small flat cutter between the cutter and the peak to preliminary loosen the soil. It is made of two plates measuring 8x3 cm. In addition, such a device provides additional alignment during drilling, which significantly speeds up this process.
  • Fourthly, you can use ready-made discs to make a cutter, for example a disc from a grinder for working on stone. It is not even necessary to cut it in half, but just cut it along the radius line and enlarge the hole in the center in accordance with the diameter of the knob. Then you can straighten it, spreading it apart different sides edges of the cut, thereby forming a kind of auger. Then weld, as in previous cases. Very a good decision is the manufacture of a cutter from a circular saw blade. Its sharp teeth brilliantly deal with the most stubborn tree roots encountered in the drill's path. It is prepared in the same way as a grinder disc.

So, we have looked at several options for making a garden auger at home. Agree, this is not very difficult for the home craftsman. All that remains is to choose the most acceptable option and make yourself this wonderful device, which long years will make work in the garden and dacha easier. And the production itself will only take about 2 hours.

Care of the device

If you want your instrument to serve you faithfully for many years, do not forget about simple rules caring for it:

  • After manufacturing, it is advisable to cover it with anti-corrosion liquid and paint it with metal paint.
  • After working with it, clean it of any remaining soil, and check the integrity of the blades each time.
  • All damage must be repaired immediately and these areas must be covered with anti-corrosion liquid.
  • Before starting drilling, it is advisable to lightly loosen it with a shovel. upper layer soil to facilitate the initial entry of the drill.

A hand drill is necessary for construction when repair work. In addition, it is often used when working in the garden or vegetable garden. Using this item, it is very convenient and quick to dig deep and narrow holes that are needed for planting trees or for installing supports during the process of pouring the foundation. In addition, the drill cannot be replaced with any other tool when drilling wells. Few people know that you can make a manual post drill yourself, saving a significant amount of money. All you need to make this indispensable tool is detailed instructions, describing how to make a drill, availability necessary materials, tools and, of course, patience.

By using hand drill Convenient for digging narrow holes for posts or planting trees.

It should be noted that the use of a hand drill is not intended for soil with stone impurities. The soil should have a clay or loamy base. In this case, the drill, as a rule, is made from high-quality materials. In this case, its service life may be unlimited.

Materials and tools

Before you begin, you need to make sure that you have all the materials and tools available. It will be much more convenient to work if everything you need is at hand.
In order to do this, you need to have:

  • welding machine;
  • welding clamps;
  • grinders with a cutting disc for iron;
  • electric drills;
  • pairs of gas keys;
  • dies, the diameter of which must match the diameter of the rod;
  • die holder;
  • vice.

Materials for making a drill: grinder disc, drill, pipes.

As practice shows, the use in this case of simple cutting inserts with sufficient large diameter, is unable to give the desired effect. A hand drill made from such material will take away your energy and time in the process of drilling earth holes. In order to avoid such a result, professionals recommend supplementing such a tool with two shortened pre-rippers. In this case, a hand-made drill made by yourself will be much more effective, and working with it will take noticeably less time.

Return to contents

Device

A hand drill consists of the following elements:

  1. Pen.
  2. Insert.
  3. Cutting attachment.
  4. Clutch.
  5. Bolt with nut.
  6. Cutting blades.
  7. Guide rod.
  8. Blade.

Return to contents

Manufacturing of pre-rippers

As for the worm version of the tool, making it yourself is quite difficult. Taking this into account, it is possible to replace the stepped auger with two welded pre-rippers having an increasing diameter of the cutting material. In this case, the soil resistance is evenly distributed over the steps, and the amount of force applied for one revolution of the drilling device around its axis is noticeably reduced.

The purpose of the first pre-ripper is to crumble dense soil, then cut a wider radius of the hole and supply the already loosened soil to the surface of the disk ripper.

The disk ripper performs the function of forming the walls of the hole, as well as pushing part of the soil upward. During one such process, the depth of the dug well can reach 40-50 cm. In the case of a large load, working with a hand drill will be quite difficult.

A good material for making pre-rippers can be a car spring, the thickness of which is at least 5 mm.

To sharpen the cutting edge of such a ripper, it is necessary to maintain a certain angle. This element should be butt welded to the main rod, after which you can begin welding the next section of the rod. The next step it is necessary to attach the second pre-ripper element to it (end-to-end). Finally, all that remains is to weld the sharp part of the rod. In this case, it is necessary to take into account the ratio of all segments, since otherwise backlash may occur.

As for the disk, the function of which is to form the walls of the hole, for its manufacture it is recommended to use processed circular saw designed for woodworking. Its thickness must be at least 3 mm. The disk is cut into two equal parts, after which its cut edges need to be sharpened. The next step is to weld the resulting pair of elements onto the main rod, while maintaining the same angle. In this way, you will be able to avoid displacement of forces, as a result of which the dug wells may turn out crooked.

Return to contents

Threading

At the opposite end of the rod it is necessary to cut a thread onto which the coupling will subsequently be screwed. For this purpose you will need a vice and a special die. Clamp the barbell (end up) in a strong vise, maintaining a right angle. In this case, it is recommended to monitor the protrusion of the rod, which should not exceed 10 cm. Otherwise, completely undesirable depreciation may occur at the moment when the die is subjected to pressure. Using a file, grind the end to form a cone. This will guarantee that the die will sit correctly and evenly on the bar. After this you can start cutting work.

There is nothing complicated in the thread cutting process. The die holder rotates slowly clockwise. If a die gets stuck during work, twist it and sharpen the interfering burr. After this, screw the die back onto the finished part of the thread and continue cutting to the planned mark. The most optimal thread is considered to be 10 cm long.

The next step is to screw a coupling onto the thread, which is welded onto the main rod in the area of ​​the connecting seam. At this point, you can safely assume that you have completed the main part of making a hand drill with your own hands.

Return to contents

Making a pen

The handle or rotating part of the hand drill is welded strictly at right angles in a T-shape. The main bar itself can have a length of 40 to 50 cm. The recommended width of the handle should be no more than shoulder width. The fact is that the rod's resistance to rotational force is limited. If it is exceeded, the rod may twist, as a result of which the hand-held pole drill will become unsuitable for work. In order to avoid such troubles, limit the effort and gradually drill the ground in moderate parts.

Before you start welding, secure the handle to the rod using a welding clamp, making sure the corners are straight. This way you will not only save correct angle, but you will also be sure that the handle will not move to the side. Weld should be like end side main rod. At this stage you should work as carefully as possible. It is worth considering that the reliability and service life of the future drill depend on the quality of this joint. Since the seam takes on all the stress, don’t skimp on the electrodes.

The uneven joints are ground down using a grinder; this will not only give the tool a more aesthetic appearance, but will also eliminate cuts on your hands that you can get while using a hand drill. Having welded the handle, a connecting thread is cut at the other end of the main rod in the same way as the previous one.