Andromeda security system. Andromeda security center software
SYSTEM
TRANSMITTING NOTICES
"ANDROMEDA"
Technical description
and instruction manual
SLGK.425698.001 TO
1. Introduction................................................ ........................................................ ......................... 4
2 Purpose................................................... ........................................................ ..................... 5
3 Technical data........................................................ ........................................................ ..... 6
4 Product composition........................................................ ........................................................ ............ 10
5 Design and operation of the SPI.................................................... ........................................... eleven
5.1 Operating principle................................................... ................................................. eleven
5.2 Working via telephone lines.................................................... ............................ 12
5.3 Operation via radio channel.................................................... ......................................... 13
5.4 Use of on-site devices in the system that are not part of the SPI. 14
6 Design and operation components SPI........................................................ .. 15
7 Diagnostics and control system.................................................... ............................. 16
8 Software........................................................................................ 18
9 Instrumentation.................................................................... ....................... 19
10 Tools and accessories................................................... ............................... 20
11 Placement and installation.................................................... ............................................... 20
12 Preparing for work.................................................... ........................................................ . 20
13 Functional test.................................................................... ........................ 21
14 Operating procedure......................................................... ........................................................ ......... 22
15 Maintenance................................................................... .................................... 23
15.1 General instructions................................................... ........................................................ .23
15.2 Types and frequency of maintenance.................................................... ................................ 23
16 Possible faults and methods for eliminating them.................................. 26
17 Indication of safety precautions.................................................... .................................... 28
18 Marking and sealing.................................................... ........................... 29
19 Packaging................................................... ........................................................ ........................... 29
20 Storage rules......................................................... ........................................................ .... thirty
21 Transportation................................................... ........................................................ .. thirty
APPENDIX A................................................... ........................................................ ............ 32
1. Introduction
1.1 This technical description and operating instructions (TO) are intended to study the notification transmission system and contain a description of the system, operating principle, specifications, information required for correct operation, rules for handling the product and other information necessary to fully use the technical capabilities of the system.
1.2 The technical description and operating instructions consist of this general technical description - SLGK.425698.001 TO and technical descriptions of the system components:
SLGK.466452.001 TO Base block BB-TSS;
SLGK.467332.001 PC maintenance of the duty operator PC-DO;
SLGK.464419.001 TO Radio unit RB;
SLGK.464639.001 TO Object Antenna AP-V;
SLGK.464639.002 TO Object antenna AP-U;
SLGK.464639.003 TO Remote object antenna AD-V;
SLGK.464639.004 TO Remote object antenna AD-U;
SLGK.425513.001 TO PPKOP NORD-8/16, 8K, 8/16N;
SLGK.425513.002 TO PPKOP NORD-8/48;
SLGK.425513.003 TO PPKOP NORD-8/96;
SLGK.426477.001 TO Object block BO-5RT;
RU. SLGK.00002ANDROMEDA software (OS WINDOWS95) CNP/WIN (Program description)
1.3 When studying and properly using the SPI, you must additionally use the following documents:
SLGK.425698.001 FO - ANDROMEDA notification transmission system. Form;
SLGK.425698.001 E1 - ANDROMEDA notification transmission system. Scheme of dividing the product into its component parts;
SLGK.425698.001 PE1 - ANDROMEDA notification transmission system. List of products;
SLGK.425698.001 KZ - ANDROMEDA notification transmission system. Execution order card;
Technical documentation supplied with purchased products included in the SPI.
1.4 In the present technical description The following abbreviations are accepted:
SPI - Notification transmission system "ANDROMEDA";
PPK - Reception and control device
PPKOP - Security and fire alarm control panel
CS - Central Station
PC - Personal computer
2 Purpose
2.1 The Andromeda notification transmission system is designed to protect objects various forms property from unauthorized entry and fires, for transmission of notifications over a dial-up telephone line and/or radio channel, their collection and processing.
2.2 SPI "Andromeda" is a unified computer system collection and processing of information. It is designed to monitor the status and receive messages from control panels that have built-in communicators (digital message transmission units), both over dial-up telephone lines and over a radio channel.
2.3 Scope of application – collection of information and monitoring the condition of objects where fire-security equipment is installed.
2.4 The equipment of the central station and the peripheral facility equipment of the SPI are designed for continuous round-the-clock operation.
2.5 In terms of resistance to the effects of climatic factors of the external environment, the Andromeda SPI CS belongs to group UHL 4 of GOST 15150, and peripheral equipment - to group UHL 3.1 of GOST 15150.
2.6 In terms of resistance to mechanical influences, SPI “Andromeda” corresponds to performance group No. 2 of GOST 12997.
2.7 In terms of adaptability for diagnosing SPI “Andromeda” corresponds to option 4 according to GOST 26656.
2.8 SPI “Andromeda” is a repairable and restored product of group II, type 1 GOST 27.003.
3 Technical data
3.1 The product is manufactured in accordance with approved technical specifications
TU, set design documentation SLGK.425698.001 and meets the requirements of GOST 26342, GOST 4.188, GOST 27990, GOST 15150,
GOST 12.2.006, GOST 12.2.007.0, GOST R50009, NPB 247.
3.2 Purpose indicators
3.2.1 Supply voltage range (for alternating current
frequency (50 +
1) Hz), V................................................... ........................................... from 176 to 242.
3.2.2 Information capacity of the product, (objects) ..................................... up to 8000.
3.2.3 Information content of the product (notices), not less................................................... .... 13,
(maximum) .................................................... ........................................................ ............................
3.2.4 Number of controlled directions when used
radio channel........................................................ ........................................................ ......................... 1 or 2.
3.2.5 Based on the results of processing the received information, the product provides the following types of messages:
3.2.5.1 Notification of an alarm event (unauthorized entry).
Notifications of alarm events include notifications:
About the activation of security detectors in loops;
About the activation of anti-sabotage sensors;
About the activation of panic buttons;
About disarming under duress.
In this case, the sound alarm should be triggered (acoustic signal of type 1) and information indicating the type of notification “Alarm” will be displayed on the monitor screen, specific type Alarms (tamper alarm, alarm panic button etc.) with recording of alarm loop numbers (if the alarm is caused by the activation of security detectors), object number, date, time and instructions for the operator.
3.2.5.2 Fire alarm notification when fire detectors are activated.
In this case, an audible alarm should be triggered (acoustic signal of type 2) and information indicating the type of notification “Fire alarm” should be displayed on the monitor screen, recording the numbers of alarm loops, object number, time date and instructions for the operator.
3.2.5.3 Fault notification
Malfunction notifications include notifications:
About a loop break;
About a short circuit of the loop;
About power outage (~ 220);
About a malfunction (low voltage) of the “backup power supply”;
About a malfunction in the power supply of the detectors;
About a telephone line malfunction.
In this case, the sound alarm should be activated (acoustic signal type 3). Information is displayed on the monitor screen indicating the type of “Fault” notification, the specific type of fault, object number, date, time and instructions for the operator.
3.2.5.4 Notification of restoration (fault elimination).
Notices of restoration include notices of restoration:
Power supply (~220);
Backup power supply;
Power supply for detectors;
Telephone line.
In this case, the sound alarm should be activated (acoustic signal type 3). Information is displayed on the monitor screen indicating the type of “Recovery” notification, a specific type of troubleshooting, object number, date, time and instructions for the operator.
3.2.5.5 Notification of taking into security.
This group includes notices of taking under protection:
Using the master code;
Using short or temporary codes;
Partial access to Home1 and Home2 modes using user codes No. 1,..., No. 28;
Automatic capture;
With a key.
In this case, the sound alarm should be activated (acoustic signal type 3). Information is displayed on the monitor screen indicating the type of “Arming” notification, the specific type of arming, the object number, date, time and instructions for the operator.
3.2.5.6 Notification of disarming.
This group includes notices of disarming:
Using the master code;
Using user codes No. 1,…, No. 28;
Using time codes;
With a key.
In this case, the sound alarm should be activated (acoustic signal type 3). Information is displayed on the monitor screen indicating the type of “Disarming” notification, the specific type of disarming, the object number, date, time and instructions for the operator.
3.2.5.7 Notification of passing the test.
This group includes notifications about passing a manual or automatic test.
When receiving a notification about a manual test, an audible alarm should be triggered (acoustic signal type 3). Information is displayed on the monitor screen indicating the type of notification “Test”, the specific type of test, object number, date, time.
If there is no reception of the automatic test signal at the programmed time, the sound alarm should sound (acoustic signal type 3). The information “No control signal received” is displayed on the monitor screen, indicating the object number, time and operator actions.
3.2.6 Technical information transfer rate, bit/s....................................
3.2.7 The product provides the transmission of notifications in a radio channel
at frequencies, MHz................................................... ...…..174) and/or at frequencies (400 – 470).
3.2.8 The product provides a notification transmission range of at least 20 km of line of sight when installing the transmitting antenna (1/4 l vibrator) at a height of 1.5 m, and the receiving antenna at a height of 30 m.
3.2.9 The product provides:
3.2.9.1 Automated logging of events on a hard disk with simultaneous printing of received notifications on a printer of current events. At the same time, information indicating all notifications, the date, and time of their receipt is displayed on the monitor screen and on the printer for listing current events.
3.2.9.2 Printout of a certain type of event log when the corresponding command is given through the menu.
3.2.9.3 Printing a specific type of event log when the corresponding command is given through the menu of the “Report Manager” subroutine.
Provided the following types protocols:
By specified object numbers, types of events and time interval;
On alarms (contains information on handling alarm messages);
According to the time of protection of objects;
By response groups.
3.2.9.4 Protection against unauthorized access to software with categorization of service personnel by access (possible actions performed).
3.2.9.5 Entry and adjustment:
Characteristics of new and old objects, respectively;
Data on service personnel;
Access levels for service personnel;
Additional information.
3.2.10 Operating conditions of use for climatic influences, the range of changes in ambient air temperature and the upper humidity value for the product are given in Table 3.1.
Table 3.1
Lower temperature value, C | Upper temperature value, C | Upper value rel. humidity, % |
|
95% at T=25° |
|||
Periphery equipment: | 98% at T=25 °C |
3.2.11 The overall dimensions of the SPI components correspond to the set of SLGK design documentation. 425.698.001 and technical documentation supplied with purchased products included in the SPI.
3.3 Reliability indicators
3.3.1 Average time between failures of the product, hours, not less....................................
3.3.2 Fixed time product service life, years, not less...................................
3.4 Design and technical indicators.
3.4.1 Purchased devices and components used in the Andromeda SPI comply with the passports and technical specifications for them.
Note: The manufacturer may replace the types of individual components, provided that this does not lead to a deterioration in the output parameters of the Andromeda notification transmission system.
3.4.2 The components used were accepted by the quality control department at the supplier and accepted by the incoming inspection at the manufacturer of the Andromeda notification transmission system in accordance with GOST 24297.
3.5 Additional technical indicators
3.5.1 The components of the product meet the requirements of electromagnetic compatibility in accordance with GOST R 50009.
3.6 Completeness
3.6.1 The completeness of the delivery of SPI “Andromeda” is determined by the execution order card SLGK.425698.001 KZ No. ___ according to the approved design documentation completed by a specialized organization.
4 Product composition
4.1 SPI “Andromeda” consists of a basic set of central station and peripheral equipment.
4.2 The central station includes:
Basic unit BB-CS (system unit with a specialized processor installed in it, a monitor and a printer for printing all incoming messages, a set of cables, an uninterruptible power supply unit);
Duty operator PC PC-DO (system unit, monitor, keyboard, mouse, speakers and printer);
Software package;
Antenna-feeder devices.
4.3 The composition of the peripheral equipment (the object part of the IFS, which is installed at protected facilities) includes:
Antenna-feeder devices;
Transmitters and transceivers;
Reception and control devices (PPK):
NORD-8/16, 8K, 8/16N;
Object block BO-5RT.
The full range of SPI components is given in the diagram for dividing the product into components SLGK.425698.001 E1.
The presence and number of system components, as well as their configuration, are determined by the order card for a specific design SLGK.425698.001 KZ.
Note - The type of transmitters and transceivers is determined by the permit issued to the end user by the State Communications Supervision Authority.
5 Design and operation of the SPI
5.1 Operating principle.
5.1.1 The system can operate simultaneously via telephone lines (from 2 to 4 lines) and via a radio channel (from 1 to 2 channels).
5.1.2 Information transfer occurs when the state of the object device changes. Messages from the control panel are transmitted in the form of a digital message encoded in a specialized format. The received message is decrypted by the central station processor, and then processed by the monitoring program and sent to the printer. Simultaneous output of information to the software and printer eliminates the loss of information in the event of any problems in the monitoring program.
5.1.2 Depending on the type of object device and its service capabilities, information about the state of the object is transmitted to the central station. PPK systems can transmit a wide range of information:
Arming (indicating the user who armed);
Disarming (indicating the user who disarmed);
Partial arming (indicating the user who armed it);
Intrusion alarm (indicating zone number);
Fire alarm (indicating zone number);
Panic button (indicating the zone number);
Lack and restoration of 220V power supply;
Discharging and restoring the backup battery;
Opening and closing the device body;
Automatic test message;
Checking the functionality of the telephone communicator and radio transmitter;
5.1.3 From 8 to 96 loops can be connected to the control panel, depending on the type. The number of loops is increased using zone expanders. Arming and disarming of the device is carried out by the user directly at the site using an electromechanical lock by turning the key or using the keyboard by entering a personal code. The object is armed and disarmed automatically without the participation of central station personnel.
5.1.4 Passive detectors that have closed or open relay output contacts are connected to the control panel.
5.1.5 The software of the base unit of the central station receives and displays on the screen all the information that is transmitted to the central station by the site devices.
5.1.6 The base unit produces a sound signal of different tones and durations in accordance with the type of message received. An indication of alarmed, armed and disarmed objects is given. The program provides for the operator to handle alarms from objects. All incoming events are automatically recorded and archived, as well as operator actions to handle alarms. It is possible to generate reports on various parameters about the operation of the system.
5.1.7 The printer is operating in permanent seal messages received by the central station (even when the monitoring program is not running). Each received message is printed with the object identification number and time of receipt. Below is a description of the string that is printed when a message is received.
PIMAR2 0502 10:27 SIREN=OF MODE=ON Alarm Zone=5
 |  |
||||
Message description (*)
Operation mode of the siren and control panel (*)
Message reception time
Object number (1-9999)
L: Telephone line number
Format type
(*) - Printer printing for PAF format.
For other formats, the printed line when a message is received will be as follows.
ADMK L4 0474 15:43C1
Event code
Message reception time
Object number (1-9999)
L: Telephone line number
R: Radio channel number (1 or 2)
Format type
5.2 Work via telephone lines.
5.2.1 To work via telephone lines, the facility equipment and the central station are connected to telephone numbers of a city or local automatic telephone exchange.
5.2.2 The object device transmits messages in accordance with its functionality and the program stored in it. The installer determines which messages about changes in the state of the device will be transmitted to the central station.
When any of these states changes, a message is transmitted to the central station.
5.2.3 Before dialing the telephone number of the CA, the PPK communicator checks for the presence of a tone signal in the telephone line. If there is no tone, the PPK communicator will disconnect from the line and then reconnect.
5.2.4 After detecting a tone signal in the telephone line, the control panel communicator begins dialing the programmed first number of the central station. The dialing method – pulse or tone – is determined using software settings in the control panel itself.
If the control panel is connected to a local PBX number, you can enter additional digits to access a local PBX.
5.2.5 After dialing the number, the control panel waits for a permission signal from the central station to transmit the message. Having received the permission signal, the PPK communicator transmits a digital encoded message. Reception of the message is confirmed by a signal from the central station. After this, the message is considered transmitted.
5.2.6 The PPK communicator, after dialing a telephone number, has the ability to detect a “Busy” signal. If the dialed number of the central station is busy, or if the central station does not answer (PBX did not work correctly), the PPK communicator dials the next programmed number.
5.2.7 The control panel provides for the possibility of connecting a telephone set to it, which can be used as a regular local or city number. In the event of an alarm or other event, the PPK communicator will disconnect the line, even if it is in this moment busy and will automatically dial back to the central station.
5.3 Work via radio channel.
5.3.1 To operate via a radio channel, a transmitter with an antenna is connected to the control panel, and radio units and antenna-feeder devices are connected to the central station.
5.3.2 When working over a radio channel, only the PAF format is used, in which all control panels of the system can transmit information.
5.3.3 The object device transmits messages in accordance with its functionality and software settings. The installer determines the types of messages sent to the CA. The types of messages transmitted to the CA are determined by the installer in agreement with the client
When the state of the control panel changes, the transmitter is turned on, and a message is transmitted to the central station via a radio channel.
5.3.4 The message transmission algorithm depends on the type of control panel and the software settings entered into it. The PPK transmitter transmits the message a certain number of times with pauses between them.
5.3.5 The central station issues a message to the printer and software only once. Repeated messages are ignored.
5.4 Use of on-site devices in the system that are not part of the SPI.
5.4.1 Site devices with a built-in digital communicator can transmit messages to the central station via telephone line. In this case, the central station will receive all the information that the service capabilities of each panel allow to transmit.
5.4.2 To operate via a radio channel of this type of control panel, an object unit (transmitter) TR-100 Stand Alone is required. The information output contacts of the PPK relay are connected to the transmitter inputs. The transmitter transmits a message about changes in the state of its inputs indicating their number, i.e., when the relay contacts on the control panel are activated. Thus, general information from the facility about an alarm or malfunction is transmitted via a radio channel, and is received via a telephone line detailed information about the event.
5.4.3 Any fire and security devices that have relay output contacts can be interfaced with the central station using the TR-100 Stand Alone (information transmission only via radio) or the BO-5RT (DLR-100) site device (message transmission via radio is possible) radio channel and telephone line).
6 Design and operation of SPI components
6.1 The design and operation of the SPI components are presented in the technical documentation supplied with incoming and purchased products (See clauses 1.2, 1.3).
7 Diagnostic and control system
7.1 SPI "Andromeda" has complex system diagnostics and testing.
7.2 The central station monitors the status of its telephone lines.
7.3 The time is set during which the “Event Manager” module of the software must receive at least one message from the central station processor. If there is no message, the software will display the message " Anxiety. Event timeout exceeded»
7.4 The software controls the receipt of signals from objects. The control time is set individually for each object in the Object Manager module. If there is no message, the software will display the message " Anxiety. No audit event received».
7.5 On-site devices can perform testing functions both manually and automatically according to an established program.
Availability of main power 220 V;
Backup battery voltage;
Status of zone loops;
Condition of anti-sabotage loops;
Keyboard connection;
Telephone line status (presence of tone signal);
Control of the electronic key loop for arming/disarming;
Voltage control of additional 12V power outputs;
Control of information reception by the central station via telephone line;
Device software settings;
Monitoring microprocessor operating parameters.
7.6 On-site devices NORD-8/16, NORD-8K, NORD-8/16N, NORD-8/96 with a connected two-channel transmitter TR-100, as well as an on-site unit (autonomous transmitter) TR-100 SA can work with the central station in two-channel mode. For this, a variant of the basic unit CS with a CMS-420 processor with two radio inputs is used, i.e., two radio units operating at different frequencies must be installed at the central station.
When the specified devices operate in this mode, messages about arming and (or) disarming and a test message about the normal functioning of the facility equipment are transmitted on the same frequency. When a site alarm or malfunction occurs, the transmitter automatically switches to another frequency to transmit the message. Thus, alarm messages are transmitted over a specially dedicated communication channel, which significantly increases the stability of the system. The recommended frequency spacing in this case is 500 KHz - 2 MHz.
The time interval through which test messages are transmitted is programmed directly by the system user. The sending time between two test messages is set in minutes. The program monitors the frequency of receipt of test signals from the object and, if a message is not received from the object on time, issues an alarm to the operator on the computer. This allows you to constantly monitor the condition of the object (the integrity of the antenna, cable, control panel).
In the TR-100 SA transmitter, for each event type, the frequency at which the message will be transmitted can be set. The time interval for the test message can also be set in minutes.
Thus, we obtain the so-called “line control”, and at the same time we do not lose the functionality of the radio channel for receiving alarm information, since it is free from background test signals. The software displays on the computer screen only a violation in the schedule for receiving a test signal from the object.
7.7 The functions described in clause 7.6 allow you to monitor the communication channel simultaneously with the transmission of alarm/service information.
8 Software
8.1 Software “Andromeda” runs under Microsoft Windows 95/98/NT operating systems. Andromeda software is intended for servicing a large number of objects (>1000) with the obligatory separation of operator functions, however, it is quite possible to use it when servicing a smaller number of objects. In this regard, it is necessary to note the following features of the system:
8.2 The software is divided into independent functional parts (modules), each of which is designed to solve a specific task. This, on the one hand, allows each module to be maximally protected from the possible failure of another, and on the other hand, allows each module to be installed on a separate computer on the network.
8.3 The software is designed to work in a network that supports the IPX/SPX compatible protocol. Thus, changes made in the IPS on any computer on the network are immediately applied to all software modules running on the network.
8.4 The rights of the system operator are determined in relation to a specific action in a specific system module. Thus, levels of operator access are implemented both to the program as a whole and to its individual components, for example, it is possible to limit operator access both to the entire “Facility Manager” module and only to the function of editing the facility security schedule.
8.5 The CA allows you to receive and process events from control panels that have built-in communicators (digital message transmission units - specialized modems). Depending on the type of control panel, its functionality and service capabilities, it is possible to obtain certain information about the state of the object from the control panel. Most PPCs can transmit a wide range of information. For example, a specific user who armed or disarmed an object; location (zone number) of alarm or malfunction (break, short circuit); partial security of an object indicating unprotected zones and much more. Thanks to this, the duty operator has the most full information both about the state of the object (armed, disarmed, alarm, etc.), and about technical condition equipment (battery is discharged, there is no 220V, the telephone line is faulty, etc.).
Centralized Andromeda Liberty remote controls based on
The Sentinel processor is designed to collect, decode and process messages received from remote object devices. The processor is necessary to build a security system for stationary objects.
Peculiarities
Up to four telephone inputs (wired or GSM) on one processor board
Up to two radio channels for receiving messages
Ability to connect to the duty operator’s computer
Filtering identical messages
Special software for setting up radio inputs (included)
Information protection: if connection with the PC is lost, all data is accumulated in a buffer. After the connection is restored, the information is transferred to the Andromeda Security Center software
Shchetenko Grigory
Director of the Technical Support Department
With a solution based on the Sentinel processor, you get a modern and reliable Central Monitoring Station.
Those. characteristics
Physical parameters
PC connection interface Radio input sensitivity. Temperature range...............
Communication parameters
Radio channel (simplex)............
Wired telephone lines, GSM networks....................................
50 mV
From +5°C to +45°C
PAR, NPAF, EPAF
PAR, NPAF, EPAF, PULSE, DTMF, ............. Contact ID, SIA, Voice
Possibilities
If necessary, you can connect a printer to print reports. IN controversial situations a printed report can be used as evidence in court.
ASViews i
A ready-made duty operator workstation is a tool for quickly deploying a monitoring station in as soon as possible. The station is a modern personal computer controlled by operating system Windows 7. The station kit includes professional Andromeda Security Center software, as well as peripheral equipment, including a monitor.
Andrey Zhuk
Project manager
To monitor objects, our company uses the Liberty station based on the SentineL processor. We recommend to our clients only that equipment in which we ourselves are completely confident.
Andromeda Liberty monitoring stations operate under the control of a licensed operating room Windows systems 7, equipped with a monitor, keyboard, speakers.
Basic equipment / Andromeda Liberty monitoring station based on Sentinel processor
Central monitoring console AED PS-512
The AED PS-512 remote control is designed to monitor the condition of objects on which fire-security equipment is installed. Provides reception, processing, storage and registration of alarm and service messages from on-site devices manufactured by C-Nord and PIMA companies. Used as part of the Andromeda notification transmission system. Receives messages only via radio channel.
Peculiarities
Two radio channels for receiving messages Up to 512 controlled objects Up to nine operator users
RAM (internal) memory for 2000 events Built-in uninterruptible power supply
LED indication.
Possibilities
Two levels of administration - Administrator and Operator with different rights and functions.
Additional output for connecting a siren.
Liquid crystal two-line display (each line contains 40 characters).
Film keyboard for control and data entry.
PC compatible (via RS-232 port).
Connecting a printer to print events.
Two remote control modes
Offline mode: receiving, processing, storing and recording alarm and service messages in random access memory remote control
Integrated: device control and object condition monitoring are performed using a personal computer and software
Andromeda Security Center.
AED remote control PS-512 exists in three modifications, which
differ in the number of controlled objects
and PC connection function.
AND PS-512/20 - 150 objects without PC access
(offline mode only); -AND PS-512/21 - 150 objects, PC output; -AND PS-512/22 - 512 objects, PC output.
AED PS-512 allows you to organize a simple monitoring center and, as necessary, increase the number of monitored objects.
Those. characteristics
Physical parameters
Input signal amplitude...
Temperature range............
Work protocols...................
From 0° C to +40° C ...........PAF/NPAF
Power supplies
Main - 50 Hz power supply with voltage 176/242 V. Backup - one or two rechargeable batteries with voltage of 12 V. Battery operating time - 8 hours. The battery is fully charged in 16 hours.
hashgaiga,
Radio unit AED RB
The radio unit is designed to receive signals from on-site devices, convert them and transmit them to the radio input of the central station.
Peculiarities
Two high frequency inputs for connecting a radio transmitter
Low frequency output for connection to a central station
Works in all bands: MW, VHF and UHF
Protection against unauthorized opening of the case - tamper
Two modifications of the radio unit - for one and two radio channels
Manufactured on the basis of transceivers from leading radio equipment manufacturers ICOM (Japan).
Those. characteristics
Physical parameters
Temperature range...................
Weight.............................................
From -30° C to +60° C ...............2 kg
Dimensions.
355x266x95 mm
Power Options
Supply voltage.
Consumption in receive mode., Sensitivity (12 dB SINAD) LF output.................................
Compatibility
Central monitoring consoles based on:
AED PS-512 (all modifications);
Sentinel (all modifications).
250 mA
0.5 W at 8 ohms
Online store shop.cnord.ru
You can purchase this equipment in our online store.
Cepheus system repeater
Receives messages from on-site devices via a radio channel and forwards them to the central station via an Ethernet network or a backup radio channel.
Peculiarities
Work in PAF and NPAF/EPAF formats
Light indication of message reception and transmission
Two security zones for organizing two security loops with three states: normal, open, short circuit
Up to 16 frequency channels for reception and transmission
Monitoring the status of the main and backup power supplies
Automatic recharging of the backup battery
Automatic battery test - every 10 minutes
Ability to work via GPRS channel (when installing an additional router with a GPRS modem).
Connecting a group of remote objects without building a network of repeaters. The distance between Cepheus and the central station is not limited in Ethernet transmission mode.
Reduced number of messages. By transmitting messages over Ethernet, radio frequency is freed up.
Constant reception of messages via radio channel. Unlike conventional repeaters, Cepheus is capable of receiving messages from object devices while transmitting information to the central station.
Substitution of frequencies. Reception of messages in one range (frequency), transmission in another.
In cases where it is necessary to build a network using a repeater without an Ethernet solution, it is possible to use the RTS-5 repeater.
Suvorov Konstantin
Director of IT Department
Today, Ethernet and IP are the most common means for organizing information transmission networks. Cepheus repeater - perfect solution to organize the last mile via radio channel and further transmission of events to the central station via existing WAN/LAN networks.
System repeater Cepheus
1. Power supply Pendant
2. Transceiver (receive-transmit head)
3. Cepheus board
4. Signal corrector board
5. MOXA interface converter
6. Lightning arrester
Those. characteristics
Physical parameters
Temperature range......................... 0° C to +40° C
Weight (without battery)........................ 2.5 kg
Dimensions.............................335x270x100 mm
Network interface Ethernet UTP 10/100 Mbit/s
Power Options
Main - AC mains 220 V 50 Hz with voltage 176-242 V; Reserve - one or two rechargeable batteries, voltage 12.6 V, capacity 7.2 Ah.
Software
Andromeda Security Center is the most common professional software for monitoring objects in Russia.
Andromeda Security Center allows you to work with monitoring stations from various manufacturers, which increases system flexibility and reduces costs.
It is possible to build distributed notification processing systems by combining several consoles into a single network. Thanks to this, several consoles are controlled from the Unified Dispatch Center.
Andromeda Security Center
Security Center is software that provides solutions to problems of receiving, registering and processing notifications from protected real estate objects.
50 OBJECTS FOR FREE
Andromeda Security Center, free edition for 50 objects
The starting edition is a working product with no functionality restrictions. Thanks to the starter edition, security companies starting their activities can minimize costs.
To get the starting edition, just download the Security Center from the website cnord.ru. The transition to the version of the Security Center with a large number of objects is carried out by installing an electronic security key. In this case, reinstalling the software is not required.
Alarm scenarios
While processing an alarm, the operator registers actions using the software: call to the facility, call and arrival of the group, decisions made and reasons for canceling the alarm.
The security center offers the operator more. When working out a fire alarm, you need to perform actions different from those performed when working out a panic button. By linking alarms and their recommended actions, Security Center allows the operator to avoid missing out on the really important things.
If an alarm occurs due to a technical malfunction at the facility, the Security Center allows you to turn it off for a limited period of time, after which the Security Center will remind you of the malfunction if it has not been eliminated by that time.
Reliable data storage
The Security Center stores data in a modern Microsoft SQL Server DBMS, which meets the most stringent requirements for reliability and performance of such products.
A well-thought-out backup system allows you to save data in any situation and in case of any failure.
All editions of the Security Center work on a single software platform designed for a large number of objects and events.
Reception of events from most remote controls
Altonika
Proxima
There are no technical restrictions on the number of remote controls simultaneously connected to the Security Center. It is possible to connect site equipment directly to the Security Center, for example, equipment operating via GSM (GPRS) or Ethernet.
Fault monitoring
With the help of the Security Center, you can free the duty operator from having to monitor typical faults at sites. For example, if 220 V is not restored at the facility within a specified period of time, the Security Center will automatically create an alarm and require an operator response. The same applies to temporary malfunctions of communication channels at sites - the operator does not need to independently control their restoration: the Security Center will cope with this task perfectly.
Detailed description of objects
If the Security Center is used, then no information about objects will be lost: each object can be described in great detail: from name to note, through separate lists for sections, loops and responsible persons. If some field is missing, you can add it; this option is also provided.
In the Security Center, information about objects is actively used: the operator immediately sees the names of alarm loops or the name of the person in charge who carried out the removal; the same information can be included in the SMS message that will be sent by the RBI.
Working with reports
The reports supplied with the Security Center allow everyone to get the information they need. Thus, the operator on duty can view received events and alarms or print a report on the shift being completed.
Using reports, the database administrator monitors the completion of site cards, and line engineers receive information about false alarms and loss of signals from sites. The management team evaluates the performance of operators, RRTs and engineers, creating appropriate analytical reports.
Login via alarm
A common security tactic is that disarming an object is always done through an alarm. The security center offers a convenient and safe solution for such objects, allowing the operator not to be distracted by analyzing alarms that are about to be cleared, but at the same time, immediately drawing his attention to situations that require intervention.
Networking
As the number of objects increases, one computer is no longer enough: the operator must respond to events coming from objects, the database administrator needs to create new objects and make changes to the cards of existing ones, and engineers need to print reports on false alarms. Thanks to the opportunity to work in local network, Security Center allows everything
Perform these actions simultaneously on computers on the network.
on different
Displaying objects and GBR on the map
The ability of the Security Center to display alarming objects and the location of the SRT on a map of the area allows you to visually represent the operational situation and significantly simplify decision-making for the operator: he simply sees what is happening.
Sharing objects between operators
When there are really a lot of objects, the efficiency of one operator on duty decreases significantly. But simple magnification The number of operators cannot solve the problem: after all, each of them will work with the same, very large amount of information. The Security Center allows you to divide information flows between operators, allocating for each of them its own range of object numbers.
Import data from common programs
Import is possible from the Guardian, CSM32, Andromeda 1.x-2.8 programs.
For creating comprehensive protection It is not enough for a building to have only video monitoring equipment: it must also have software that manages all surveillance elements. Among the Russian control systems, the Andromeda security system with a wide range of actions stands out, which has various functionality. The main distinguishing characteristics of Andromeda is the ability to operate on equipment from different manufacturers, as well as the ability not only to control all video monitoring and protection mechanisms, but also to perform notifications and monitor the situation at the facility.
Characteristics of the security complex and features of the functions performed
Andromeda is practically an entire software package that includes a various list of functions and additional features. The main distinctive characteristics of the system are:
- Manufacturability and practicality;
- Flexibility and adaptability various options equipment;
- Functionality and user-friendliness of the interface;
- Speed of data reception;
- Creation of graphs;
- Reporting;
- Connection to the central server.
The video explains how the security alarm works:
The security system performs all the functions inherent in access control systems, as well as video monitoring programs and warning systems. The main functional features of the system include:
- Reception of signals from sensors and sirens;
- Signal processing;
- Fire response management;
- Notification using light and sound sirens and annunciators;
- Monitoring several objects simultaneously;
- Carrying out monitoring and sending reports to the security console.
The security system is designed taking into account the expansion of the number of connected devices. This avoids the need to replace the software with a newer one, and also, thanks to its operation via the network, it becomes possible to update automatically, without the intervention of specialists. Thanks to the simple Russian-language interface, managing the program is easy.
Program modules and additional functions
The average warranty period for all equipment provided by the company is 4 years. The company's specialists perform setup and further warranty service.
The Andromeda security complex includes the following modules:
- Settings Manager;
- Setup program;
- Personnel Management;
- Processing events and notifications;
- Object management.
Each program module performs clearly defined functions. Observation of objects is carried out from one central control room, equipped with a monitor, on which events from all video cameras installed in various rooms are displayed.
Central control allows you to zoom in and out of an object, making it possible to see even the visitor’s appearance or license plate number.
Andromeda software simultaneously coordinates the operation of equipment from several places, but this requires a local network connection.