Galvanized mesh for fences. How to make a sectional metal fence from welded mesh Fence from welded mesh distance between posts

If you want to save money, you can make a fence from welded mesh with your own hands. This design is suitable option both for a summer residence and for a private home. However, you first need to choose a material, since it should be understood that welded mesh can be of several types. The quality of the entire product will depend on the material chosen.

You should be aware that not all types of fencing can be installed between closely spaced areas. This is due to the fact that monolithic structures great heights shade the space. Considering the small size modern dachas, then you should understand that in this case almost all the plants in the garden will grow sluggish. For this reason, there will be constant complaints from owners of neighboring plots. The solution is to use a mesh that is not an obstacle to the light of the sun and air masses.

A mesh fence can be used not only at the dacha, but also to fence off sports facilities, technical areas or reservoirs.

Today there are the following types of grids:

1. Galvanized mesh. A layer of zinc is applied to steel parts. This is done before or after welding. This best option in case you want to receive durable design for little money.
2. Non-galvanized mesh. This material is the simplest and requires minimal cash costs. This product is made of steel. The diameter of the rods is approximately 1.2-7 mm. The disadvantage is that this product is not coated. This a big problem, since there is no protection from the influence of external factors.
3. Galvanized product with a special coating. This option is durable. The only drawback is the high cost.
4. Product with polymer coating. Has protection against corrosion and other factors.

How to mark your own site?

First of all, you will need to install temporary pegs in the corners of the area, between which the thread will be stretched. The length of the cord will be length the desired mesh, however, it will need to be purchased with a margin of several meters. After this, you should designate the places where the columns will be placed. The recommended distance between the posts is 2-2.5 m. If you make a larger distance, the lattice may begin to sag.

You should know that on a site with a large slope it will not be possible to install a mesh fence, since it is impossible to securely fasten the material at an angle.

In this case, the only way out is terracing the area, which involves installing columns of greater length and strength in places where there is a difference. On one side of the column the grid will be fixed at a level above, and on the other - below. To do this, the mesh will need to be cut into individual elements. If it is not possible to do this, then you can install a sectional fence for your summer cottage.

At the moment, there are two ways to build a mesh fence. The first method involves tensioning the lattice between the posts. To implement the second method, you will need to make metal corners, into which the lattice elements will be fixed. The first option is easiest, but it should be noted that it is less durable and aesthetically attractive.

Additional costs will be required for the manufacture of sections Money. The cost of the corner can significantly exceed the cost of the mesh itself.

In all cases, installation of a welded mesh fence involves the use of posts. These elements can be constructed from metal or wood. The first option is budget and affordable. However, you should buy supports made of wood only if their cost is several times less than a metal product. Also wooden structures suitable if you only need to install a temporary product.

There are also situations when material remains after the construction of a private house, but there is no desire to throw it away. In order to exclude extra costs, you can apply the existing columns.

Metal posts will last for many years. The most commonly used support elements are square section, their diameter ranges from 7 to 12 cm. The thickness of the tube wall should be more than 2 mm. If you want to save money, you can purchase the material at a scrap metal point, where you can often find great options pipes

Return to contents

How is a mesh fence installed?

For work you will need a screwdriver, a building level, a tape measure, a bayonet shovel, and pegs.

If you have decided to install a mesh fence, then the first step is to prepare everything necessary tools and materials. To work you will need the following elements:

• metal pillars for the construction of a frame structure;
• elements for fastening posts (bases, clips for connection, brackets with nuts and bolts and clamps U-shaped);
• roulette;
• water;
• screwdriver;
• pegs;
• cement mixture;
• building level;
• concrete solution for the base of each column;
• sand;
• rope;
• a bayonet shovel, with which you can dig holes for posts.

Return to contents

Sequence of actions for installing the fence

To install a welded mesh fence with your own hands, you need to perform the following steps:

1. The first stage of installation is marking. The perimeter is preliminarily outlined and the location of the fence is indicated. You can measure the distance between the holes using a tape measure. The distance from one column to another is equal to the width of the sheet, but you should take into account the diameter of the column and the margin for the base. For example, with a cut width of 2 m and a column diameter of 10 cm, the distance between the supporting elements should be measured to be 2.18-2.2 m.
2. On next stage holes are dug. Their diameter should be larger diameter columns by 1-3 cm. Here it is important to take into account the base made of concrete or cement. This must be done using a drill. If of this device is not available, you can use an ordinary bayonet shovel. The depth of each hole should be approximately ¼ of the length of the post. However, the depth of soil freezing should also be taken into account. The larger it is, the deeper the holes should be. In most cases, columns with a height of 2 m are prepared. In Russia, winters are quite severe, therefore approximately 15-20 cm must be added to 50 cm (¼ the height of the supporting element). In this way, the depth of one hole can be obtained.
3. At this stage, the installation of support columns is carried out. You need to pour a mixture of cement into the hole. To prepare it, you need to mix one part water with one part cement mixture and three parts sand. Next you need to insert a column. It should be noted that in some cases it is placed in a special base. The column is aligned using building level. You need to hang the tool on the top of the post and make sure that the level is perpendicular to the ground and parallel to the supporting element. Next, you need to fix the device with spacers and wait until the base hardens.
4. After approximately 24 hours ( given time on average it takes for the base to harden) you can begin installing the mesh. It should be fastened using special fastening elements or U-shaped clamps. To fix it you need to use a screwdriver. It is recommended to fix the mesh in several places of support. If the mesh is not cut into sheets, but is secured in a roll, then staples should be used for this. Special attention you need to pay attention to the fastening elements, since the reliability of the entire device will depend on them.
5. Finally, the mesh fence will need to be painted with moisture-resistant paint.

Some dacha cooperatives do not provide for installation between plots or any other similar material, since such structures shade small areas. In this case, a fence made of welded galvanized mesh becomes an excellent solution. It will not prevent ultraviolet radiation from entering the area and will not make it difficult natural circulation air and can be erected by any summer resident.

Preparation

Chain-link is an inexpensive material that is ready to last for quite a long time. An additional advantage is the ability to use it as a support for climbing plants. This mesh was invented at the end of the 19th century, but is still widely used today. Every consumer can purchase it.

To create a fence, in addition to the mesh, you should prepare reinforcing bars, thick wire, and cable. When choosing a grid, you should pay attention to the size of the cells. The smaller it is, the more expensive the mesh will be, but also stronger. If the mentioned parameter is equal to the limit from 40 to 50 mm, and the roll width is 1.5 m, then this material will be an excellent solution for creating a fence for a summer cottage.

Tension fence

A fence made of welded galvanized mesh can be tensioned. This method of making it is the simplest. After all, the material will have to be stretched between the pillars, which can be made of the following materials:

• concrete;
• wood;
• metal.

The number of supports will depend on the pitch between them and the length of the fence itself. Best distance The parameter is 2.5 m. Pipes can be used as pillars, but they must not be damaged by corrosion. On sale today you can also find ready-made poles that have hooks and a painted surface. Before installation, it must be treated with a protective compound.

As alternative solution The mesh protrudes towards them and is fixed with a clamp or wire. The height of the pillars must be calculated. If the clearance between the ground and the fence is 5 to 10 cm, then the underground part of the support and the width of the mesh should be added to this parameter. The load on the corner pillars will be greater, so they need to be placed deeper than the others. Therefore, their length should be longer ordinary pillars 20 cm.

When making a fence from welded galvanized mesh, you must concrete the bases of the supports to increase strength. The pillars will form the frame of the structure. After installing them, you can begin fixing the mesh. As soon as the concrete hardens, hooks are fixed to the posts or welded if the post is metal. The material for fastenings should be:

• wire;
• nails;
• rod;
• screws.

You can use any other material that bends into hooks. At the same time, the roll is straightened and installed at the corner support, the mesh must be hung on the hooks.

The roll needs to be unwinded one span to reach the next post. The rod is threaded a little further than the place where the mesh will connect to the post. The master should hold the rod and tighten the mesh. If a rod is not used, the mesh may not be tensioned evenly.

It is better to carry out this work with the help of another person. He will hold the grid at the bottom edge, while the other master will hold the grid at the top. At the next stage, reinforcement is threaded into the mesh; it is necessary to retreat 5 cm along the edges. When installing a fence made of welded galvanized mesh, it is necessary to weld horizontal rods or attach them to posts.

Without using rods, over time you will encounter the fact that the mesh will sag. When the technology is followed, rods are used to maintain tension. The mesh should be pulled further according to the principle described above, fixing and pulling the rod or wire. At this point we can assume that the fence is almost ready. The hooks are bent on the posts, the last of which are painted. It is recommended to fold the wire antennae downwards to reduce the risk of injury. The wire is usually threaded through the top edge of a row of cells, and the protruding edges should be wrapped around it.

Sectional fence

To build a sectional fence, you will need sections where the mesh will be installed. At the first stage, you should use a technology that is similar to that described above. To do this, the area is marked out, and then poles are installed.

Installation of a mesh fence will involve the use of a corner whose dimensions are 40 x 5 mm. These elements will be needed to make the frame. Its length is determined taking into account the distance between the pillars; 15 cm must be subtracted from this value. The same amount should be subtracted from the height of the pillar above the soil level. This will give you the width of the frame.

The corners need to be welded into rectangular structures. The size of the sections is made taking into account the size of the mesh, which varies from 1.5 to 2 m. Galvanized welded mesh in rolls, if necessary, can be cut with an angle grinder.

Work methodology

At the next stage, metal strips are welded to the pillars. They should be placed horizontally. Their length can be from 15 to 25 cm. As for the width and cross-section, they are 5 cm and 5 mm, respectively. With a deviation of 20 cm from the edge of the post, it is necessary to install a section between the two supports. Welding is used for this. At the next stage, you can start painting the fence.

Fence cost

Quite often, summer residents and owners of territories within the city ask themselves the question of how much a galvanized mesh fence costs. If the width of the material is 1.5 m, then you will have to pay 310 rubles for such a fence. behind linear meter. Using a mesh whose width is 1.8 m, specialists charge 390 rubles for their services. per linear meter.

Pulling reinforcement will cost the consumer 40 rubles. per linear meter. You may also be interested in the question of how much a fence costs. If its length is 50 m or more, then you will have to pay 355 rubles per linear meter. This price is correct for structures in which the reinforcement is installed in one row. The mesh width is 1.5 m. This parameter will be equivalent to the height of the fence. If it increases to 1.8 m, then the cost will rise to 415 rubles. The price includes metal supports, pulling reinforcement in one row, galvanized mesh and installation work.

Mesh cost

If you decide to do the work yourself, you can inquire about the cost of the mesh. If the diameter of the wire used is 1.2 mm and the mesh size is 10 x 10 mm, then pay for square meter the material will cost 455 rubles. The price per roll will be 6825 rubles.

Galvanized mesh, the cell size of which is 20 x 20 mm, will cost the consumer 234 rubles. per square meter. In this case, the diameter of the wire used is 1 mm. But the price per roll will be 7020 rubles. With an increase in cell size to 25 x 25 mm, the cost increases to 416 rubles. per square meter. In this case, the wire diameter is 2 mm, and the price per roll will be 12,480 rubles. Galvanized welded mesh 50x50 mm will cost the consumer 312 rubles. per square meter, while the price of the roll will be 7020 rubles, and the wire diameter will be 2.5 mm.

Conclusion

Galvanized welded mesh in rolls will be an excellent material for making a fence. It is easy to cut, it is quite simple to pull it between support pillars In addition, it is durable. And in some cases, a mesh is the only correct solution when it is necessary to fence an area, but it is necessary to provide access to sunlight.

Fence welded mesh

Welded mesh fence

In order to protect your personal plot or a dacha area, developers often use welded mesh fencing. The popularity of this material is explained by the following positive qualities, How:

• low cost and availability;
• ease of installation work;
• Beautiful appearance fence;
• low windage of the fence in strong winds;
• ability to transmit sunlight well.

However, some owners of individually built houses consider the transparency of the fence to be a serious drawback, since everything that happens in the fenced area can be seen from the street. Therefore, welded galvanized mesh and galvanized mesh fences force us to eliminate this vulnerability.

In this case, you can reduce the transparency of the fence by stretching a masking plastic sheet over its surface. plaster mesh made of PVC, which builders often use to hide the facades of buildings when carrying out repairs and construction work. This PVC with various color shades is durable, inexpensive and reduces the level of transparency by at least half. Some owners of private housing constructions, to reduce the level of transparency, sit near the fence, which, growing, close full review plot from the street.

Types of mesh fences

According to their design, welded mesh fencing comes in two types: sectional or modular and continuous (roll). Sectional ones are frame structures made from a corner or profile pipe, inside of which it is located. The frames are installed between the posts, creating a beautiful and reliable fence.

For continuous coverage, welded road mesh is most often used, which is rolled into rolls and simply stretched along the line of installation of pillars or fills the gaps between them.

Modular welded structures are very convenient for constructing fences in difficult terrain and ensure the rapid construction of fences. Solid fencing is cheaper and easier to install.

When choosing the type of fence design made from metal fence mesh, you need to take into account your requirements for operational characteristics, design reliability and available financial capabilities. All steel mesh fencing can be classified according to the type and method of installation of the fence.

Types of mesh used for fence construction

Modern market building materials offers developers the following types:

• simple black, resistance welded from wire with a cross-section from 1 to 6 mm;
• welded galvanized;
• with polymer coating of various colors;
• combined welded, with a protective zinc and polymer coating at the same time;
• flat made of black steel rod with a diameter of 0.6 to 1.2 mm, a square or profile pipe with a section of 10x10, 12x12, 15x15 mm;
• 3-D or euro mesh, which has a three-dimensional configuration and is made of a rod or square, like flat gratings.

Welded mesh for fence in rolls

Application protective coatings make already welded mesh. Galvanizing or applying polymer coatings protects the fencing material from corrosion, but significantly increases its cost. However fixed costs painting a fence made of black mesh involves material costs of

protective coating is quite justified. In addition to galvanizing and applying a polymer coating, a mesh made of ordinary ferrous metal, manufactured in a factory, can simply be painted with powder or another method, which significantly reduces its cost.

Installation of a welded mesh fence

1. Installation of a fence made of welded mesh of any type always begins with the installation of posts, for which it is best to use steel round or profile pipes.
2. After installing the pillars light mesh you can simply pull it between them, using two stretched wire strings running along the top and bottom of the fence as load-bearing hangers. The strings will hold the fence mesh securely enough, preventing it from sagging and bending. The mesh itself is simply tied to the posts with steel wire.

1. Another installation method is called modular and involves preparing rectangular frames from angle steel and stretching the mesh inside such a frame.
2. After manufacturing, the frames are installed between the pillars and secured by welding.

Flat welded steel mesh from a rod or square is manufactured in a factory or independently at the site where the fence is installed. It is a flat welded grid with cells 100x50, 150x50 or 200x50 mm. The size of such gratings should correspond to the distance between the pillars and their height. The finished mesh is secured between the posts by welding, using a steel clamp, or tied with wire.

3-D fences or euro mesh are manufactured only in the factory and resemble flat bars, but with a voluminous bend of the rods, which gives it a very original look. It can also be mounted on poles using welding, clamping clamps, or simply tied to supporting structures.

Very popular in Lately became a sectional fence made of mesh or welded fence"Cascade" type. Its sections are made in a procurement workshop from vertical and horizontal rods with a diameter of 3-5 mm. The design has fairly good rigidity and has cell sizes from 50x50 mm to 75x100 mm. Standard length span 4600 mm. As anti-corrosion protection polymer or powder coating is used. Fastening each individual panel to the posts using clamping clamps without welding.

The design of fences made of galvanized mesh or gratings allows you to erect fences of any height and install individual sections on different heights, which is very important when the fenced area is located on a slope.

DIY welded mesh fence

How to make a fence from welded rolled mesh: preparation

Before starting construction work, it is necessary to accurately determine the choice of fence design and prepare the materials necessary for its construction. For any mesh fencing you will need:

• pillars made of steel round or profile pipes 5/4 of the fence height;
• cement, crushed stone and sand for preparing concrete;
• boards or other material for formwork;
• tie wire or fastening clamps;
• welded steel mesh corresponding to the fence design you have chosen.

Marking

The construction of a fence begins with marking the lines for its installation. To do this, pegs are driven in at all turning points and on straight sections at a distance of no more than 5-6 meters and the cord is pulled. Using a tape measure, the places where the posts need to be installed are marked. The distance between the posts must correspond to the size of the purchased mesh panels or is taken equal to 5 meters when using rolled material.

Earth and concrete works

In the places where the pillars are installed, it is necessary to dig holes with a size of at least 400x400 mm and a depth of at least ¼ of the height of the fence. The pillars need to be installed vertically in these holes, supporting them with inclined supports for stability. When installing, using a stretched cord, you must check that the top edge of the pillars is at the same level. To better secure the supports in the foundation, transverse rods can be welded in their lower part.

After installing the pillars and checking their vertical position using a building level, the holes are filled concrete mixture in a volumetric ratio of 3 parts cement, 4 parts sand and 5 parts crushed stone. After pouring, a break of at least 48 hours is taken to allow the concrete to harden.

To give the fence a more aesthetic appearance, many developers pour a concrete lintel between the posts. This is not mandatory, but the appearance of the fence with this base is much better. For the device, you need to dig a trench 15-20 cm deep and pour a layer of medium-fraction crushed stone 10 cm thick onto its bottom. After this, install the formwork along the entire length and pour concrete inside it. It would be advisable to reinforce this structure only if installed on heaving or waterlogged soils.

How to attach welded mesh to a profile pipe

If you have a welded fence mesh in rolls, then attach its edge with wire to the first post. Unrolling the roll, gradually attach it to each subsequent post with wire. The ends of the roll should rest on the post, so determine the distance between the tables in advance in the following way: if the roll is 15 meters long, then the distance between the posts is 3 meters.

To prevent the mesh from sagging too much, you can thread steel wire into the cells from above and stretch it between the posts. Some builders also thread the wire through the bottom to add vertical tension.

When the entire mesh is well tensioned, you can use special fasteners for welded mesh instead of wire. They are different types, one of the options is shown in the picture on the right. They are fastened with metal screws.

Attaching the welded mesh to profile pipe is not self-tapping screws without additional fasteners good option, since the soil moves and the mesh can jump out from under the screw.

VIDEO: Fence made of welded mesh with polymer coating

Sectional fence made of welded mesh

Installation of a fence made from welded sections of all models, due to their structural rigidity and preliminary factory preparation, is not difficult. Therefore, if you have an assistant and the necessary tools, you can install the fence yourself. Fence sections made of welded mesh are shown below in the figure.

When purchasing poles and sections of welded mesh, as a rule, they are purchased immediately (so as not to run around and look for suitable ones later) full set its fasteners:

• clamps;
• staples;
• a set of hardware (bolts, nuts, washers, etc.).

Installation of sections is not difficult. It is quite possible to do it yourself.

When constructing a fence, it is not always possible to use materials that have a monolithic surface. This most often applies to those situations where it is necessary to delimit adjacent garden plots in which crops are grown. various plants. In this case, it is most advisable to build a fence from a welded mesh with your own hands. Such a structure will save the neighbor’s and your own territories from shading and will not interfere with the full development of plants, thereby causing discontent among people living in the neighborhood.

Material selection

First of all, you need to choose what type of material the welded mesh fence will be made from. There are four main options, which differ from each other in coating.

Uncoated mesh

It is usually sold in rolls and is cheap. Its use would be appropriate among bushes, since the surface of this fence will very quickly become covered with rust. Painting will be economically infeasible and labor-intensive. On the other hand, if there is dense vegetation at the border of the plots, and you need to protect yourself, mainly from migrating animals, then this option is quite acceptable.

Galvanized mesh

Perhaps the most practical material would be this kind of material. It is not much more expensive than the first one, and taking into account the total price of the entire structure, the difference will be about 10%. After all, the price of the structure includes pillars, hardware and components for concreting the supports.

Galvanized painted mesh

Its coating is applied according to the same principle as on corrugated sheeting. First, the product is galvanized, and the top is also painted. This is very reliable coverage. The only thing it is afraid of is abrasive effects. Rains and watering the garden lead to regular splashing of the soil-containing substance, which leads to the abrasion of the protective layer and subsequent corrosion. Therefore, it is recommended to attach such material slightly above the ground surface, and if it is necessary to seal the lower space, you can build a concrete or other base.

Polymer coated mesh

This type of protection is the most expensive, but also the most effective. It is resistant not only to temperature influences, but also to friction. In the most visible areas, it is worth using this option, since it has a beautiful appearance and will allow you to isolate the territory to the entire required height without additional costs.

In addition to the fact that the material differs in the type of coating, it can also differ in the method of execution, which can be:

• Welded flat mesh
• Welded mesh 3d for fence

The last name is produced by specialized enterprises, which, complete with this name, supply special poles and fastenings to create an aesthetic and reliable fence.

Preparation of tools and material for sampling

Once the welded mesh for the fence has been selected, you can proceed to preparatory work, one of the stages of which is the recruitment of the work contractor necessary tool. This is an important stage, since the inability to carry out this or that operation will greatly slow down the construction, and the material prepared and laid out on the site will create interference. Therefore, it is best if all the necessary components have already been purchased and delivered to the construction site. Here's what you'll need:

Tools

Surely everyone assumes that you will definitely need basic tools, such as:

• Level
• Pegs
• Roulette

Digging tool

Any means for digging holes that are found on the farm will be suitable. The hole drill can be used either manual or electric. Of the shovels, the most convenient will be the “American” one, since it has a curved end, and this is very convenient when digging holes for posts.

Container for mixing the solution

• Concrete mixer (if available)
• Trough with hoe or shovel (optional)

Tools for installing mesh

• Welding machine (if fasteners will be used with it)
• Drill
• Screwdriver
• Screwdriver
• Bulgarian
• A piece of reinforcement or thin pipe for stretching the mesh

Materials

Let's figure out what materials will be needed to install a welded mesh fence and decide on their choice.

Pillars

It is best to use round or profile pipes with a diameter of 40-150 mm as pillars. It is permissible to use concrete or wooden supports. In the latter case, it would be better to protective treatment wood

Cross bars

To create additional rigidity for the mesh covering, you can use thick wire threaded through the mesh. Also, spans can be attached to pipes or fittings attached between the pillars in the upper and lower parts. You don’t have to do this if the supports are often installed and the mesh has sufficient rigidity.

Wire can be used up to 5 mm. It is recommended to use fittings or pipes for rigid fastening from 10 mm.

Fasteners

To attach the mesh you can use:

• Bolt hooks (best option)
• Self-tapping screws
• Metal plates
• U-shaped clamps
• Brackets with bolts and nuts

Materials for concreting supports

• Cement
• Sand
• Rubble stone, slag or crushed stone

Fence installation

Like any other type of fencing, metal fence You need to start making it from welded mesh in stages.

Site marking

With this procedure, it is necessary to take into account, first of all, the distance between future supports. It depends on their height, the thickness of the selected material, and the parameters of the material that will cover the spans.

The recommended distance in such cases is usually 2-3 meters. A more frequent arrangement of racks will entail additional consumption of material for them; a larger distance will require the use of transverse stiffeners, which will have to save the mesh from sagging. When marking, it is necessary to take into account the dimensions of rolls or finished sections of mesh, as well as the dimensions of the entire area. All these values ​​must be compared and the distance between the supports must be planned so that the joints of the fence covering fall on the surface of the posts.

Installation of pillars

To do this, you need to dig or drill holes in the marking areas. The depth can be within 0.7-1.2 meters. This depends on the size of the posts and the density of the soil. It is also worth considering the landscape of the earth's surface. On slopes, the depth of the holes needs to be greater. This is not only necessary because in such places the soil tends to slide, but also because inclined surfaces Streams of water flow when it rains. This leads to softening of the soil and a decrease in its ability to hold objects fixed in it.

After the pits are ready, prepared supports are installed in them and concreted. In this case, it is necessary to strengthen the installed racks with wedges in order to avoid tilting during the process of pouring and drying concrete.

Mesh installation

Installation is best done no less than 7-10 days after concreting the supports. It is during this time that the cement composition will gain the required installation strength. Although many craftsmen install the mesh the very next day, this is not the best option

If transverse pipes will be involved in the fastening, then you need to immediately weld them or attach them with self-tapping screws. It is better if these stiffeners are placed between the sides of the racks that face each other. With a carefully selected size of the jumpers, they will act as spacers and protect the supports from coming together under the influence of the tension of the mesh.

When used against sagging wire, it is threaded after hanging the mesh, but before tensioning.

The diagram below shows various options fastening welded mesh with clamps

The mesh covering of the fence can be attached in several ways:

• Welding
• Using clamps
• By hanging on hooks
• Self-tapping screws and pressure plates

It is important that when attaching the mesh, it is tensioned in a timely manner. If the installation is carried out using hooks or self-tapping screws with plates, then first you just need to hang the material on them, and then tighten it evenly.

When welding fastening, the mesh must be tensioned immediately until final fastening. The material must be tensioned using a vertical pipe or fittings threaded through it, as discussed above. At least two people must participate in this process. One produces tension, while the other attaches the mesh to the post. The use of a vertical rigid rod is due to the need to produce uniform tension over the entire height, which will be very difficult to do by hand.

Now all that remains is to decide on the method of attaching the mesh and begin installation

Final actions

After hanging the mesh covering, you need to check the level of all racks, paint the fastening joints (if necessary), pillars, transverse pipes or tensioned wires.

With proper preparation, anyone with minimal training can build a sectional fence made of welded mesh House master. There are several recommendations that will help you get the best results:

1. It is important to monitor the level at all stages installed poles and do not use excessive force when pulling the mesh.
2. Before painting any metal surfaces worth cleaning thoroughly sandpaper, degrease with solvent and prime. This will ensure the durability of the paint and protect against additional expenses further.
3. If under the main fence it is planned to carry out concrete plinth, then it must be done together with concreting the pillars.
4. When working with cutting and welding mechanisms, you should not forget about your own safety measures and use protective equipment and clothing.

Photos of welded fences

We have selected interesting photos welded mesh fences. Please note that the installation and assembly of this type of fence is quite simple and inexpensive. Therefore, this type of fence is more suitable for summer cottages

Fences made from mesh are very popular; they are indispensable in cases where you need a reliable fence with good light transmission and a low price. Besides modern fences made of welded galvanized mesh are very attractive, durable and easy to install with your own hands.

Classical country fence made of galvanized welded mesh

Advantages of galvanized mesh

They produce galvanized mesh from metal wire. Its rods are arranged perpendicularly and are fastened at the connection points by welding. The cells of the welded mesh are made rectangular, square, less often diamond-shaped, trapezoidal or other shapes. The wire for the mesh is galvanized or with an additional polymer coating.
Fencing made of welded galvanized mesh has its advantages:

Types of welded mesh fences

Depending on the type of coating, it is presented in the following types:

Galvanized mesh can also be produced in the following types:

Drawing of a section of a fence made of galvanized mesh

How to choose a galvanized welded mesh fence

Features of installing a fence made of galvanized mesh

There are two ways to install galvanized mesh:

• Tension of the fabric between the pillars;
• Installation of sections.

The first option is cheaper and easier to do yourself. But the second option is considered more aesthetically pleasing and stronger.

If you do not purchase ready-made welded spans, you will have to make the sections yourself from angles or profiles.

Fence posts can be either or. Of course, if you build thoroughly, you should use steel supports with a cross-section from 6 to 12 cm.

Installation of pillars

Installation of mesh on supports

To pull rolled mesh, hooks are welded onto the posts. Also, special poles with hooks can be purchased ready-made.
The galvanized mesh is hooked onto the first post and stretched with tension to the next support and put on the hooks again.

One of the options for attaching fence sections to posts

To make a galvanized mesh fence stronger, a wire with a diameter of 4 mm is threaded through its top and bottom. The wire is welded to the post.
It is difficult to pull the mesh evenly with your own hands, so it is advisable to invite an assistant and, by threading a crowbar or rod through the bottom and top of the welded mesh, pull them. After installing the fence, the hooks are bent.
A sectional fence is either welded to posts or secured using pipes and clamps.