The most beautiful DIY bird feeders. Photo report “Decorating a bird feeder

Wooden bird feeders are quite durable. They look beautiful and will allow birds not to starve during the cold season.

Simple DIY wooden bird feeder

Depending on what materials you have, will be made wooden feeders.

To create one like this, take:

• round wooden rods;
• board;
• waterproof glue;
• nails;
• necessary equipment.

The feeder drawing will allow you to create it.

These dimensions are provided in inches. But knowing that there are 2.6 cm in one inch, you can create this product. First you will need to saw off a 20 cm long rectangle from the board. Drill holes, stepping back a little from the corners. These recesses will be at a distance of 2.5 cm from the edges. Sides will need to be attached to the base so that the food does not spill out. Make them from narrow boards. Place two on the edge and two on a wide surface.

Now you need to saw the wooden rod into pieces 24 cm long. Attach them to the previously created recesses. From above, these rods need to be fixed to the roof. It consists of two boards that are located at an angle of 90 degrees to each other. Tie a thick rope and use it to secure the wooden feeder at a height.

Sprinkle some treats for the birds, they will be happy to fly here.

Wooden bird feeder in the shape of a house

This one has an opening roof. But you can make it cohesive. First, make a bottom tray, which will also become the floor, and on it you will lay out treats for your feathered friends. To do this, attach 4 edges around the perimeter to the plywood.

Now take the bars and assemble two walls from them, as in the photo.

Attach these two sides to the base of the wooden feeder.

From above, fix the walls in this position using two small bars.

Taking a special or regular ruler, draw an angle on the board. Saw it off and attach such a gable to the top of the feeder, where the roof will be.

Determine where the hinges will be. Attach them to wooden boards.

Pre-drill holes in the gables to thread strong rope through, as shown in the photo.

Secure it so that similar wooden feeders hang securely on a hill.

To make such a cute birdhouse, take:

• processed wooden board width 14 cm;
• nails or screws;
• hook;
• rope;
• tools.

First, saw off 18 cm from the board. This rectangle will become the floor. You will need to attach 2 parts with pediments to it. To do this, you need to cut 2 boards 20 cm long and sharpen their upper parts at an angle of 45 degrees.

Fix these walls with gables on both sides of the floor. Additionally, secure with boards 13 cm wide. Make gable roof from two rectangles of boards 20 cm long. The roof should protrude slightly beyond the wall so that precipitation does not penetrate inside and raindrops flow out. Use a hook to secure the rope from which you will hang such a beautiful wooden feeder in the shape of a house.

If you want the lid of this device to open, then attach these elements using hinges.

This bird house is attached using 2 hooks. You can make round windows on the sides to be able to observe the birds from all sides. The following diagram of the feeder will allow you to make it perfectly level. But the calculations are given in inches.

The dimensions for the following bird house are also given in inches.

Let's do a little math, you will multiply the presented numbers by 2.6 cm. For convenience, the result can be rounded. Then you will need to cut the boards from which you will make the base, two side panels with gables and two narrow walls. You will also need a couple of boards for the roof. Using fasteners, secure the rope, the edges of which are placed in the holes in the wall.

The following diagram of the feeder will allow you to arrange all the parts correctly and determine the size of this product.

Wooden bird feeder with dispenser - step by step photos

This will allow you to always see how much food is inside. It will not get wet and will nourish the birds for a long time. Assemble a feeder that consists of a base and a roof. You need to attach rounded wooden rods to the base by inserting them into the recesses made. Then the birds will be able to sit on these perches and rest comfortably. Connect the roof elements together and attach them to two triangular gables. Make two holes at the top of 1 and 2 halves of the roof. The same ones need to be done at the bottom of the base.

Cut four rounded notches in the center. Take a jar with a tin screw cap. Make holes in the lid. Pour food into the container, screw on the lid and place it in the middle of the floor. When the supply of food in these recesses runs out, it will be automatically replenished from the jar, and the birds will not remain hungry.

You can place a plastic bottle inside a wooden feeder. To do this, you will need to make a recess in the roof, after pouring the food into the bottle, tighten the cap.

Beautiful wooden houses for birds - master class and photos

You will be able to see how much food is left and admire the birds without disturbing their peace.

Look at the diagram of a wooden feeder.

As you can see, the birdhouse consists of a base, two sides, a pair of side walls, a gable roof and a ridge for it. Sheets of transparent plastic are placed vertically on the sides. They need to be fixed so that there is a small gap at the bottom. Then you can pour food inside, and it will automatically pour out into the space accessible to the birds. But make the roof open so you can replenish food supplies for the birds through the top.

You can make this feeder with a dispenser to look like a cabin on the ocean. To do this, construct a roof from large and small branches.

Place large branches at the bottom so that birds can sit comfortably and take food from a plastic container.

Decorative elements for a wooden feeder

These are the words that can be used to describe other bird houses.

This wooden feeder doesn’t even require wood. After all, it is located on the counter. In addition to this bird canteen, there are two boxes in which you can plant greenery or flowers. Take a block of wood for the main post and secure its lower end in two perpendicular boards. To do this, you need to make a recess in the center of 1 and 2 boards and compare them. But first do it in the middle of each through holes according to the diameter of the bar. Now connect this lower part of the feeder using self-tapping screws. Look at how the roof is constructed.

As you can see, it is parallel to the feeder itself. To secure some of the elements of this bird canteen to wooden beam, you need to drill holes in them, as well as in the block. Place the edgings on the glue, inserting them into the holes made.

The elements that you will attach to the edges must be secured using clamps. Hold them until the glue dries.

Once the stand is done, all that remains is to paint it. Fill wooden boxes with soil and plant flowers there.

The next wooden feeder is fixed on a tripod, and the house is made in the form of an open gazebo. Down, food spills out onto the floor. Birds fly here and feast on it.

The next wooden feeder is also an item for decorating the area.

From two small planks, make a cross on which the timber will be attached.

Install it in the holes made and secure it with small oblique blocks.

Cut out 2 oval pieces and make 3 holes in one.

You can insert containers into the holes into which you will pour bird food.

Fasten together a solid oval part and with holes. Place food containers on top. They must have a mechanism that allows the birds to retrieve food.

If you know how to cut wood, then use a jigsaw to make shaped edges for the next structure. This will also be a wonderful decorative element.

Hanging wooden bird feeders

If you need to do it quickly wooden house for birds, then the following ideas will help.

For this you will need the following:

• four wooden planks;
• aluminum screen;
• nails;
• hammer;
• metal strips;
• wood glue;
• tools.

You need an aluminum screen in the shape of a square with sides of 25 cm. Take 4 planks and glue them together. Also additionally secure them at the corners with nails.

Use nails to attach the metal strips over the screen. They need to be placed end to end to form a box. Drill holes in the corners of this device where you will attach the hooks. Attach a chain to each using pliers, fix the upper ends on a large link, and then hang this device.

If you wish, make a similar feeder, but paint it in White color. This one looks especially beautiful against a green background.

To do this, you also need to knock together four boards, placing them on edge to form a box. You can use an aluminum screen or a sheet of plywood as the bottom. Secure any of these materials with self-tapping screws. Then attach beauty hooks to the sides so that the birds can rest here. IN drilled holes insert the fasteners and hang the chain to secure the feeder in an upright position.

And if several birds flock to you at once, then the next hanging feeder will do.

Use round plywood as a base. If you don't have one, cut one out of a square sheet or use a whole square one. Drill four holes on this tabletop so that the fixture will then hang level. Make 4 drawers from the boards or use ready-made ones. Attach a plastic bowl to the center. All that remains is to paint the tabletop, attach the rope and hang the device.

Do-it-yourself vertical bird feeders - master class and photos

These will save space and use vertical rather than horizontal space.

For such a device, take one and a half meters of boards 15 cm wide and a stainless wire mesh. First, saw the board so that you get 3 sides of 20 cm each. These will be the bottom two side faces. The top one should be a little larger so that it protrudes from the right and left. Cut two rectangles of wire to size, insert each into grooves made in advance on the sides and bottom.

Attach a semicircle of wood to the bottom using nails and glue.

Drill holes at the top of the feeder and insert a bent brass rod here. It also needs to be secured to the upper sides of the product.

The following vertical bird feeder will allow them to rest and feast at the same time. These are especially loved by nuthatches and tits, which perfectly hold on to vertical supports.

Take:

• rectangle board measuring 25 by 23 cm;
• rounded perches;
• chain;
• hooks;
• tablet;
• wood glue

The prepared board needs to be sharpened at the top, then several indentations are made in it.

You will do them using a drill required diameter. Some holes should be the size of the poles. You will place them on glue and fix them in the recesses. Now you need to mix the birdseed with a small amount of peanut butter to make a viscous mass, and place this treat in the made recesses. Now you can enjoy watching how the titmice appreciate your efforts.

The next vertical feeder is attached directly to the wall or fence.

Take:

• wooden board;
• hot glue;
• nails with a hammer;
• plastic bowl;
• a wooden stick rounded on the sides.

First, it is better to cut out the parts on cardboard or paper in order to be able to compare them and make adjustments to these templates.

In the board that will be the floor, drill a hole in the side center to pour glue here and fix the wooden perch. Now knock down the roof elements, attach them to the wall, and attach the floor. You also need to glue the plastic container so that it does not get blown away by the wind and birds do not accidentally drop it. When the glue dries, it’s time to pour food inside the container and wait for guests.

This next vertical feeder is also quite nice. You need to use nails and glue to connect the gable roof to the walls, and them to the floor. Attach a treated rounded wooden board with holes in it at the back. Use these to hang a chain or rope to secure this bird canteen. You can draw or glue their images, then such wooden feeders will look even more interesting.

The vertical one can also be attached to the window using a suction cup. Then, while at home, you will be able to watch how the birds fly to you to feast on food.

To set up this bird canteen you will need these suction cups with fasteners. On the one hand, they will be fixed on the window, and on the other hand, you can fix them on the window using self-tapping screws. wooden plank. Knock down a wooden box. To do this, the floorboard must be level, and make a bevel at the top of each sidewall by sawing one board in this way.

Now on top you can attach sloping roof, it will be located on a bar that is fixed on the two upper parts of the sidewalls. Cut holes here in advance to secure the two upper suction cups. Now you can fix the roof and attach the feeder to the window.

You can make it open. To do this, knock down a box, make it from plywood or aluminum sheet or plastic mesh bottom. Fix this device on two vertical bars. Attach suction cups to it, or you can fix hooks on top and hang it on the window.

You can also attach a horizontal feeder near the window, securing it with chains. To ensure that the birds have a varied menu, stuff slats between the parts of the bottom to separate the dishes.

And if you use transparent plastic, then you pour food between its two sheets, make a hole at the bottom so that the food pours out here in doses. Then you can watch the birds, and they watch you.

The next wooden feeder, made with your own hands, is also very interesting. Side bars and walls are secured using metal corners. This feeder is attached to the wall using special fasteners. Its walls are plastic, they are not closed on the sides, so that food can be poured through these holes, and the birds can flock to the treat.

You can fix it on wood window frame outside or on a block placed vertically, the next bird feeder.

First you will need to cut 8 boards of the same size. Make an octagon out of them by attaching them as follows.

Attach one board from one opposite side to the other, attach two more perpendicular to it, so that you get a cross like this inside. Attach the bottom, making it from wooden sticks or from plywood. Take a strong narrow board and attach two wooden fragments cut at an angle to its ends. Using one you will attach this leg to the bottom of the feeder, and the second will help secure this bird's dining room to a vertical wooden support.

DIY log bird feeder - step by step photos

Such wooden feeders also look very interesting and will be useful for birds.

This bird's canteen looks natural. It seems as if the titmouse is simply jumping on a log in search of food, but in fact the product was made from a log.

To do this, you need to cut off an element from the log required size, hollow out the wood inside, leaving impressive side walls. Attach hooks at the top and bottom for fastening. Now you need to put food here, but regular food will spill out, so do it as follows. Take coconut or peanut butter and melt it on low heat. Then mix the peanuts with other grains. Place the resulting food into the hole of the log, press with a spoon so that the treat fits tightly into the container.

Now pour a small amount of prepared melted butter on top and let the structure harden. When this happens, use hooks to hang this wooden feeder in place.

The birds will surely appreciate your efforts. If you have small logs or twigs, use them to make a roof for your next feeder.

To do this, you need to saw the logs in half lengthwise and make a roof out of them, attaching them with reverse side up and down the board. Fix 2 planks on the created base, they will become vertical walls. Attach the structure to a log dug vertically into the ground.

If you do not have suitable boards, but only thick branches or thin logs, then make the basis for a bird's dining room from them.

Attach a sheet of iron or polycarbonate on top, and at the bottom attach this structure to a rectangle of plywood.

If there is a log, then special tools remove the middle from it, place this structure on its side and hang it. You will get a wonderful house for birds, into which you will pour food for them.

The next one is also quite easy to do. If you do not have oval blanks, then you can cut the handle from a rake or shovel, and also take bars.

For birds, you need to have a few simple items and tools.

You can make a feeding trough with your children, but keep in mind that you need to watch every step, since during the construction process sharp things are used - scissors, knives, screwdrivers and even, sometimes, a saw.

There are many options for feeders - made of plywood, plastic bottle, tin can or cardboard.

Here are the most interesting, popular and original ideas creating a feeder:

Feeder made from scrap materials: toilet paper rolls

You will need:

1 bushing from toilet paper

Peanut butter

Small bowl

Plate

A couple of branches

Strong thread or fishing line

Knife (dull or plastic).

1. Connect two branches or sticks together using hot glue or string. You can skip this point if you make 4 holes in the sleeve (see below).

2. Make holes in the toilet paper roll so that you can thread two branches or sticks through them. It is better to make 2 holes: a little higher and 2 slightly lower (see image). This item is not required, because The sleeve can be put on differently.

3. Place the peanut butter in a small bowl and use a plastic knife to spread the butter onto the surface of the cardboard toilet paper roll.

4. Sprinkle the food over the peanut butter sleeve.

5. Repeat steps 3 and 4 for 4 more bushings.

6. Tie a strong thread to the connected branches so that the structure can be hung.

7. Hang all the cardboard tubes on the branch structure, and then hang everything on the tree.

Feeder made from a plastic bottle. Option 1.

You will need:

Any plastic bottle

Ribbon, thread or fishing line

Awl or drill (for making holes in the bottle and plastic cap)

Bolt and nut

Stationery or simple knife (if necessary)

Deep plastic plate.

1. Prepare a plastic bottle. Remove the label from it, wash it well and dry it.

2. Make a hole in the middle of the lid and plastic plate.

3. Attach the lid to the plate using a bolt and nut.

4. Make a hole in the bottom of the bottle (bottom).

5. Make several holes on the side (4-5), near the neck of the bottle, so that the food can spill out when you turn the bottle over. Holes can be made with a stationery knife if the bottle is not too thick.

6. Take the ribbon, fold it in half, and tie the ends in a knot. Thread the ribbon through the hole at the bottom of the bottle.

Now you can pour food into the bottle, screw on the cap and turn it over. The ribbon will allow you to hang the feeder on a branch.

Bird feeder made from a plastic bottle. Option 2.

You will need:

Plastic bottle

Plastic container

Strong thread or fishing line

Screwdriver or nail

Knife (simple or stationery).

1. Remove the cap from the bottle and the cap from the container.

2. Place the bottle cap on the container cap (in the center) and trace with a pen, felt-tip pen or pencil.

3. Using a utility knife, cut a hole in the lid of the container. The hole can be made slightly smaller than the diameter of the bottle cap.

4. Make one hole along the edges of the container lid.

5. Make a hole in the center of the bottle cap. The hole should be large enough to allow bird food to spill out.

6. Place the cap on the bottle and then insert the bottle into the hole in the container cap.

7. Tie a strong thread to the bottle and put the cap on the container.

Now you can pour food into the bottle or pour water and hang the feeder on a tree.

How to make a feeder from a box (photo instructions)

Original polymer clay feeder

You will need:

Polymer clay

Rope

Thick wire or piece of aluminum

Baking bowl or any other utensil that can be placed in the oven

A small piece of fabric.

1. First roll out the clay on a flat surface until it is about 6mm thick.

2. Carefully place the rolled out clay inside the baking bowl. Trim off any excess pieces so that the clay lies flat. Make 3 large holes in the clay for the rope.

3. Place the bowl of clay in the oven. Read the clay instructions carefully to know how long it takes for the clay to harden in the oven.

4. When the clay has hardened, carefully remove it from the bowl, tie three pieces of rope to it - tie a knot at one end of each rope, and insert the other end into the hole of the clay plate.

5. Tie all ends of the rope and secure them with wire.

6. It is advisable to place a small piece of fabric inside the plate so that the birds do not accidentally peck the clay along with the food.

Original do-it-yourself pumpkin feeder

You will need:

Small pumpkin

Wooden crossbars (even branches can be used)

Thin wire.

1. You need to cut off the top part of the pumpkin.

2. Using a knife or screwdriver, make 4 holes in the pumpkin to insert branches or wooden slats into. Make 2 opposite holes at the same height and two other opposite ones slightly lower - this way you will have one branch slightly higher than the other.

3. Take a thin wire and wrap it around each end of the branches so that the feeder can be hung on the tree. Connect all the ends of the wire so that the feeder can hang evenly. Twist them into a hook.

Original DIY bird feeder idea

This feeder is suitable for sub-zero temperatures.

You will need:

Large plastic bottle

Small plastic bottle or small plastic container

Scissors

Coniferous branches

Berries (optional)

Seeds

1. Cut off the bottom of a large and small plastic bottle. First you can make a hole with a knife and then cut with scissors. You will have the base of the feeder.

2. Place spruce branches, berries and seeds in a circle in the cut-out bottom of a large bottle.

3. Place the bottom of a small bottle or small plastic container in the center of the base.

4. Pour earth, sand or pebbles into a small container.

5. Tie strong threads or fishing line to the feeder so it can be hung.

6. If you put the feeder in the freezer overnight, and then take it out and put it away plastic parts, then you get an ice feeder.

How to make a feeder with your own hands using a bottle

You will need:

Small glass or plastic bottle (preferably with a cap)

Small saucer or bottom of a plastic bottle

Wire

Saw (if necessary)

Screw half ring (hook).

1. Using screws, connect two small pieces of plywood. In this example, the dimensions of the plywood are 11 x 15 cm and 31 x 15 cm.

2. Using the bottle that you will later attach to the stand, mark the places where you will need to attach two pieces of wire - one at the neck, the other at the bottom of the bottle.

3. The neck of the bottle should be approximately 3-4 cm above the base.

4. Drill holes for the wire, insert your wire through the bottom, wrap it around the bottle and secure it to the back of the plywood (you can twist the wire or secure it with a stapler).

5. Fill the bottle with seeds, screw the lid on so as not to spill the seeds, turn it over and insert the bottle between the wires, place a saucer under it and remove the lid.

6. Screw a half-ring screw into the top of the plywood to hang the feeder.

Original DIY bird feeder

You will need:

Tin can (preferably with a lid)

Sisal rope (sisal rope) or thick rope

A piece of thin plywood, a branch, or any small metal piece

Hot glue.

1. If you have a jar with a lid, then the lid needs to be bent in half.

2. Take a small branch, piece of plywood, or other small piece that birds can perch on and glue it to the can.

3. Insert the bent lid as shown in the image (slightly inside the jar and over metal part), and secure it with glue.

4. Take a thick rope or rope about 80 cm long and start wrapping the can so that the long ends of this rope (30 cm) remain at the beginning and at the end. Use glue to secure the rope to the can.

5. Cut the rope, tie the ends in a knot and secure with glue.

You will need:

3/4 cup birdseed

1/4 cup water

1 packet of gelatin

Twine or strong thread

Cookie pans

Baking paper.

1. Mix gelatin with water (1/4 cup) and bring to a boil, stirring. Make sure the gelatin is completely dissolved.

2. Remove from heat and let cool.

3. Add 3/4 cup birdseed. You can add more if it fits.

4. Place the cookie cutters on baking paper and fill them with the resulting food mixture.

5. Cut a piece of thread and tie its ends into a knot. Partially insert the thread into the mixture.

6. Leave the mixture to dry overnight, making sure to turn it occasionally when you have time.

7. Remove the molds and hang the food on the tree.

How to make your own bird feeder using tin cans

You will need:

3 cans of paint or cans

A piece of branch or wooden stick

Hot glue

Paints (if desired).

You can paint the jars, or you can leave them as is.

1. Glue a piece of branch to a jar for the birds to land and eat.

2. Wrap strong thread or ribbon around the jar and tie the ends in a knot. You can secure the tape with glue so that it sticks better to the jar.

3. Fill the jars with food and you're done!

How to make a bird feeder from a plastic bottle

Bird feeders can be seen in yards and parks. If you want to design something special, extraordinary, then we will tell you how to make a bird feeder yourself.

An easy way to give food to birds

A feeder can be made from available materials, for example, take a piece of board, plywood or any flat and durable material at hand and place it higher from the ground. This way the food will remain available to the birds.

This is a temporary measure, as precipitation may fall or the feed will simply be blown away by the wind. But such a feeder can save birds from starvation.

We use plastic bottles

From a plastic bottle you can build both a very simple and a multifunctional dining room for birds. Let's take a closer look at some feeder ideas and their implementation.

Hastily

If we cut a hole in the side of the bottle, we can say that we have done half the job. Near the neck you need to make 2 holes with an awl, insert a wire and secure the feeder to a branch of a tree or bush. If you pour food on the bottom, after a while you will be able to see birds flocking there.

To prevent moisture from spoiling the food if precipitation gets inside the bottle, drainage holes must be made in the bottom of the container.

Complicating the design

You can make a feeder with a “dispensing window” from a plastic bottle. Having selected a container of suitable size, cut a small hole on one side and pierce the bottle with scissors on the opposite side. Insert the wooden spoon with the handle forward so that it fits tightly into the pierced hole. The spoon should be positioned so that the grains roll into it as the birds peck at the food. The number of spoons involved may vary, but most often there are two.

To hang a bottle, you can pierce the cork with an awl (or nail), thread a nylon thread through it, and tie a knot inside the cork.

How to decorate a gray, unsightly bottle? If desired, you can make the feeder a decoration for any garden.

Glass feeder

You can make a simple design from a plastic bottle, which will be attached directly to the glass using suction cups. The design of such a feeder is very simple, and to make it you will only need 1 container and 2 suction cups.

A small square or rectangular hole is made with a construction knife. Using a soldering iron or a nail heated on gas, you need to make 2 holes on one side of the bottle into which the suction cup heads will fit tightly. In our case, the suction cups had hooks, so we first removed them, and then secured them with them, inserting them into their places, but inside the bottle.

The positive aspects include the fact that you can watch the birds by getting almost close to them. Significant disadvantage is that the birds defecate near the feeder, so the glass and tide will have an unsightly appearance.

Video: making a feeder from a plastic bottle

Use of glass

Glassware can be used to distribute food to birds. The container must be securely fastened with the neck down at a short distance from any platform. Pour food into this container and place it in place (holding the hole with your finger so that the grains do not spill out). As the feed is consumed, the food in the bottle will be released onto the site.

Video: glass feeder

Other materials at hand

It won’t be difficult to come up with a lot of ways to feed birds.

Tits love not only grains. You can feed such gourmets by hanging a piece of unsalted lard wrapped with rope or wire on a branch.

If you buy products packaged in nets in supermarkets, then this container can also be used by pouring nuts into it.

You can form a ball from small bulk food (adding flour and water) and also hang it in a net. In frosty weather, food can be mixed with vegetable oil. Milk or sour cream is not suitable for these purposes, since the bird’s body does not accept such food.

In order to protect the food from precipitation, you can build a roof from plywood.

Pumpkin

A pumpkin feeder can be called a waste-free production, since the birds first eat the food, and then the edible “dining room” itself. All you have to do is cut holes in the pumpkin and remove the core.

You can cut the pumpkin in half and thread a rope through both halves with a knot tied at the bottom. To fix it in a disconnected state, you need to install spacers made of twigs between the halves. As a last resort, you can use pencils as stands. The top edge of the rope threaded through the pumpkin is tied to a branch, and the feeder is ready to receive feathered guests.

Video: pumpkin feeder

Sofa spring

Things and items that usually have nowhere else to be used can be used.

If you have a spring left over from an old sofa, you can also use it by holding pieces of bread between the coils. This feeder can be hung both vertically and horizontally.

Car air filter

Feeder from metal mesh can be seen on the store counter, but a similar structure can be built from a used paper car air filter.

To make it, you need to cut off the top part of the filter and remove the paper filling (you can do it together with the inner or outer mesh, if you do not plan to put food between them). Outside the filter, to the top of the mesh, a wire is tied, which will serve as a loop for hanging the feeder on a tree. Suitable food is poured inside, and the cut off upper part of the filter can be used as a lid.

To reduce feed loss, you can glue the lid of a plastic bucket to the bottom of the feeder with hot glue. You can make a canopy from the same cover.

Teapot for brewing

If you have an old kettle and it would be a pity to throw it away, but it can no longer be used for its intended purpose, then you can make a feeder out of it. How to hang it? Drilling a hole in a piece of earthenware is a very thankless task, so you can use hot glue. If there is a hole in the lid, then you need to insert the ends of the rope into it and make a knot inside. To be on the safe side, it is better to tie a small washer. Now the lid can be glued to the teapot, the neck of which will now serve as an entrance for the birds.

Looking into a barn or pantry, you can find things that are “hard to carry, but a pity to throw away.” This category includes an old metal bread bin. You don't need much imagination to place it - just tie a rope and hang it on a branch.

You can use an unnecessary plastic container in a similar way.

Using different boxes

It will also be easy to make a feeder from a juice or wine box.

One or two windows are cut out in the box so that there is a small bowl at the bottom for food.

When cutting out a window, you can take care to protect the food from precipitation. For this, a small visor is left, but to prevent it from falling down and blocking the entrance, it can be secured with a nylon thread in the open position.

To make a large cardboard feeder you will need a large box. A window is cut out using a construction knife or scissors. the right size. If the box is very large, then you can cut out a smaller product from it and wrap it with tape. It is important to realize that such a feeder will only last until the first rain.

Tin box

Manufacturers often sell products in tin boxes, which can also be used to make a feeder.

In addition to the jar itself, we will need:

• metal or plastic chain – 2 m (4 pieces of 0.5 m each);
• split ring (used for keys);
• small cotter pin – 8 pcs. (you can get by with knitting wire);
• awl;
• alcohol marker;
• wire cutters or metal scissors;
• ruler;
• pliers.

Now let's start manufacturing.

• As accurately as possible, you need to mark 4 points on the jar and transfer the same marks to the lid.
• Using an awl, you need to make holes according to the marks so that the cotter pin fits through them.

• Using wire cutters, cut the chain into four pieces of 50 cm each.
• Having threaded the cotter pin through the outermost link of the chain, insert it into the hole and use pliers to push its ends apart from the inside of the can.

• Having measured 15 cm of the chain (starting from the can), thread the remaining 4 cotter pins into it and secure the lid with them.
• Now we will pass a split ring into the ears of the free ends of the chain.

After hanging the feeder on a branch, look in which direction the box slopes, and pierce it with an awl in the bottom (from the inside) - this will be a drainage hole.

Branches

From large branches you can assemble an original feeder. To complete the job you will need an axe, a hammer, nails and a little imagination.

Plywood

Plywood products are quite durable, but are susceptible to moisture.

A simple version of the feeder consists of just a pallet with sides, two pieces of plywood that serve as a roof, and a rope connecting all the parts. To fix the bottom and roof in the desired position, knots are tied on the rope.

If you have the desire and a jigsaw, you can design a more complex feeder using one of the presented drawings.

Log

When preparing firewood, logs with rotten cores are encountered. This piece of trunk will serve as our base. You need to remove the core. Windows are drilled into the hollow trunk or cut out longitudinal part. The ends are closed with selected “plaques”, sawed off from other trunks. A tree trunk feeder can be found in both horizontal and vertical versions.

For production you will need:

• self-tapping screws;
• small nails;
• slats.

To make the roof and bottom, you can use plastic or HDF (whatever you can find, since this material is sold only in large sheets).

When making any design, it is convenient and practical to use drawings that indicate the dimensions of the parts. We will also use the drawing to cut all the blanks to size.

They can be lightly sanded.

First, we will assemble the narrower part of the future feeder, hammering 3 nails on each side.

Then the entire frame is assembled in a similar way. If the nails are short, then you can use 5 pieces each.

We will install the frame on the prepared bottom and outline the outside with a pencil - this will give us a marking according to which we will need to cut out this part and then nail it.

In order to fix the top slats, we use 4 self-tapping screws - 1 pc. for each attachment point.

From the remaining slats we will make the upper part of the feeder, fastening the parts with self-tapping screws. The final stage will be marking, sawing and securing the roof. The junction of two sheets of roof sheathing can be hidden by nailing an angle strip on top.

There are some points that need to be taken into account when making and determining where to install the feeder:

1. You should not underestimate cats, because they can get to the feeder, and then the birds will fly away or become prey to a domestic predator.
2. The feeder needs to be made with big roof, then a lot of precipitation will not fall into it.
3. The entrance to the feeder should not be small, as fear may be stronger than hunger, and the birds may not take advantage of your hospitality.
4. It is better to make the structure from moisture-resistant material, then it will last a long time. Other materials must be treated with water-repellent compounds.
5. If the feeder is too light or has a large windage, then a gust of wind can turn it upside down. Even turning over for a short time will result in all the food ending up on the ground. Lightweight design needs to be made heavier.

Photos of original feeders

Video: original ideas brought to life

Drawings and sketches

Winter is just around the corner, and it’s getting harder for the poor birds every day to find food for themselves. Let's help them, at the same time teach our children kindness and mercy, caring for our little brothers. In return, grateful birds will delight you with simple but cheerful songs, as well as sketches from their bird life. If you place a video camera next to the feeder, you can eventually get an exclusive story in the style of “In the Animal World” and show it at school during an environmental or biology lesson. In general, in this article we decided to talk about what a bird feeder you make yourself should be like. We will offer a description and photo.

Making a simple feeder with your own hands

First of all, inspect the proposed material from which you plan to make a feeder, and estimate your capabilities. Also consider some design requirements:

• Remember, it should be convenient for the birds, as well as for pouring and removing food.
• It must have protection from wind and precipitation; the wind can simply carry the food outside, and precipitation can cause the food to freeze or mold, which is also inconvenient for the birds.
• The material from which the feeder is made must be moisture-resistant so that it does not have to be repaired or remade several times during the winter.
• There should be no sharp edges or corners on it, so as not to injure the birds.
• If you plan to feed small birds, then the feeder should be made small so that large and aggressive birds do not rob it and scare away small birds.
• It is better to place your feeder on tree branches or attach it to the walls of a house or household. buildings, no lower than one and a half meters from the ground, so that cats do not get there, and it is convenient for you to replenish food supplies.

Plywood option.

Of course, you can buy it ready-made in a hypermarket. But to make it yourself, and even together with your children - what could be better if your sons help you, and your daughters look at such a handicraft father with different eyes! Moreover, there are no difficulties here. It can be made closed, open, with gable roof. On the Internet you can easily find any drawings with ready-made sizes and patterns. Choose any!

For small birds you need to take into account the size of the structure so that the big voracious crows wouldn’t even think of poking around there, it would simply be very uncomfortable for them there.

1. So, prepare for work a jigsaw, a hammer, suitable nails, sandpaper, glue on water based, plywood, 20x20 cm block. Let's start with the simplest option.
2. We make the bottom 25X25 cm, and make the roof larger so that water flows past without getting inside. We mark the remaining parts according to the patterns on plywood.
3. Be sure to use sandpaper to properly sand the sawn edges so that no burrs remain.
4. We cut the block into 4 racks 25 - 30 cm long.
5. If you plan to make the roof flat on a slope, then make 2 of the 4 bars shorter by a couple of cm, and on a slope.
6. We first glue all connecting places with glue, and then fasten them with nails. We attach the racks to the bottom, and the sides to them.
7. We fasten the roof on top of the racks with self-tapping screws.
8. Now all that remains is to fix the feeder in the chosen place and pour treats there.

Options for a wooden feeder.

This is a more durable material. If you have the skills to work with wood and tools for processing it, feel free to get down to business. You will need a board 18 - 20 cm thick for work, in addition, prepare a block of 4.5x2 cm, a square piece of plywood 25x25 cm (bottom of the feeder), and for the roof 2 pieces of 35x22 cm, as well as self-tapping screws, glue and nails.

Homemade feeder made from a milk bag/box.

Here we are talking about how to make a bird feeder. The next option is the most basic. Even a child can handle it. We take:

• Clean bag/box of juice or milk.
• Wire or rope made of nylon for hanging.
• Marker.
• Band-Aid.
• Stationery knife or scissors.

First, we mark and cut out holes for the birds on opposite sides. We protect the cut edges with adhesive tape so that the birds do not get hurt. We poke holes under the holes and insert scraps from bird holes rolled into tubes, and above the holes we make holes for wire or rope for hanging. We attach our feeder to a branch.

It can also be attached to a tree, but then you need to make holes not on opposite sides, but on close ones, to make it easier for birds to approach.

There is a version of the feeder made from two bags, it turns out to be triangular in shape. We cut off the first bag by 2/3 and cut out the front side at the bottom, this will be the bottom. And we cut the second bag from below along the narrow sides, but do not touch the top. Now we combine both parts and secure them with glue or tape.

1.5 - 2 liter bottles also make feeders.

Option 1. Cut holes on opposite sides of the bottle free form. When cutting holes in the shape of the letter P, you can bend the uncut part upward to create a rain shelter. Be sure to stick an adhesive plaster or tape on the bottom of the cuts to prevent damage to the bird's legs. You can make holes in the bottom and insert sticks, this will be a perch.

It can be attached to a tree or hung on branches if it is in a lid with inside Tie a rope in knots in the holes to make a loop that needs to be thrown over the branches.

Option 2. The feeder is a bunker. Most country option, if you visit there only on weekends. Then there will be no need to monitor the replenishment of food every day; it will gradually fill up on its own as it is eaten.

To do this, take a pair of identical bottles. Make a hole near the bottom of one bottle. Upper part delete. We cut a symmetrical pair of holes at the top for further hanging. We make several holes at the neck of the second bottle; the supply of food will pour in there. Straightaway large holes It’s not worth doing, then expand them as necessary. Now we fill in the actual food and insert it into the first cut bottle.

Option 3. Feeder with spoons. We make holes in the lid and insert a rope in the form of a loop. Next we make symmetrical holes for the spoons. We make a larger hole on the side of the cup so that food can spill out. All that remains is to fill the feeder and hang it up.

It is advisable to make several small holes in the bottom of any bottle feeder with a hot needle or nail to drain moisture.

Bird feeder from a five-liter bottle.

Bird feeders can be made not only from wood. We offer you products that were created from other available materials. The feeder looks very interesting for birds from a plastic bottle. Spending one evening and feeding the birds all winter is not a useful activity for a stormy autumn evening! There is a five-liter container in every home, and a considerable number of birds can easily be fed from such a container. The main thing is to make more holes.

The whole family can take part in the manufacturing process; you need to prepare pruners, a bottle, a knife, wire or rope to attach to the tree.

First we decide how the feeder will be attached to the tree, then we mark the future holes.

If it is placed vertically, then we retreat 5 - 7 cm from the bottom and make several square or triangular holes.

If horizontally, then cut wide holes in the neck and bottom of the bottle.

Wire or twine will perfectly secure the feeder to the tree. To prevent the wind from rocking it, you can put a quarter of a brick on the bottom, and then pour food on top.

Such a large bottle can also be used as a bunker option. Then, in addition to the 5-liter bottle, you will need 2 1.5-liter bottles, a marker, a knife and a string.

• We mark holes for birds on a 5-liter bottle, a couple, and one larger one for a one and a half liter bottle.
• We make the hole for the bottle U-shaped, bend the visor up, and seal the cuts with adhesive tape.
• For a one and a half liter bottle, we make holes at the points of contact with the bottom of the five liter bottle and a little higher, so that food can spill to the bottom as needed.
• We cut a hole in the cap of a five-liter bottle so that the neck of a one and a half liter bottle can be seen from there.
• From the second one and a half liters we cut off the neck in the form of a funnel, and put it on the protruding neck of the first 1.5 liters.
• Everything is ready, all that remains is to attach the bird's canteen to the tree.

A shoebox would make an excellent feeder.

A shoe box or similar in size, maybe laminated, made of thick cardboard, is suitable for making a feeder. Everything is already there - roof, bottom, walls, only minimal work remains - cutting the necessary holes and attaching them to the tree. Needed here stationery knife, marker and tape with cord. If there is no lamination, the tape will help protect the feeder from bad weather. The bottom must be weighted with sand or pebbles so that it does not sway in the wind, and after pouring food, hang it on a tree.

There is another option - we attach the lid with tape perpendicular to the inside of the box, the lid will actually be a table with food, and the box will be both a roof and a side. We make a hook from wire, and after piercing the top of the feeder, we hang it to the chosen place. All that remains is to pour in the food and arm yourself with a camera or video camera!