Installation of door handles in interior doors. Installing a door handle on an entrance and interior door Diameter of the hole for the interior door handle

Let's say you bought a new one interior door and decided to assemble it ourselves door frame and install this very door without any experience. Well, it happens that you have to do some things for the first time. The most important thing here is to take your time and be attentive to what you are doing.

When I had to install interior doors in one of the apartments for the first time, I must admit, while sawing the first frame, I made a mistake. As a result, I had to buy a new box set. Since then, I have been very attentive and careful when performing work on assembling and installing doors.

When sawing door frame elements there is no room for error, you need to remember this. As they say, measure twice - cut once!
So, the door was delivered and has been standing in the corridor, perhaps for the second week. There’s nowhere else to put it off and it’s time to get down to business. A reasonable question arises. Where to start?

Marking the door leaf for insertion

You should start by marking the place on the door leaf where it will be built-in handle with latch. The door leaf is, in fact, the door itself without additional elements, frames, extensions and trim.

First, decide in which direction the door will open; the position of the bevel of the latch tongue will depend on this. Now you need to determine the height at which the door handle will be located. As a rule, the handle is embedded at a height of 90-100 cm from the floor or threshold. There are, of course, no thresholds in the rooms. But in the bathroom or toilet, they are very possible.

In box with door handle, you will almost certainly find instructions with the dimensions by which you need to mark. Often the dimensions are indicated on the box itself. Ordinary handles are almost always installed in the same pattern. In shops construction tools We sell special kits for inserting handles into interior doors. The set consists of feather drill, with a diameter of 23 mm. and wood crowns with a diameter of 50-54 mm.

So, mark on the end door leaf a distance of 95 cm. Using a square, draw a clear line perpendicular to the end of the canvas. Mark the middle on it and mark it. You can use any sharp object, an awl, a nail or a self-tapping screw. At this point you will need to drill a hole for the latch. But don't rush, it's not time yet!

Need to continue markings for pen, or speaking professionally, for knoba. To do this, you need to extend the line at the end further onto the canvas itself on both sides. This must be done strictly perpendicular to the door leaf, using a square. It would be useful to remind you that the pencil must be sharpened.

Here you should pay attention to one detail. The handle can be positioned at a distance of 60 or 70 mm. from the edge. Allows you to do this adjustable design latch length. Decide which distance suits you best and mark the desired distance on both sides of the canvas on the lines drawn earlier.

Please note that on a blank canvas, that is, one that does not have decorative elements in the form of slats, glass, etc., the distance from the edge where the handle will be embedded is not critical. After all, the canvas is absolutely even and smooth. But the presence of decorative inserts can limit the position of the handle. And if you decide to embed the handle at a distance of 70 mm. from the edge of the door leaf, be sure to make sure that the handle does not block decorative elements. Otherwise, make a mark of 60mm. from the edge.

Drilling a hole for the handle

Drills first hole for pen, then for latches. It is more comfortable. Firstly, when you start drilling the end, you will know exactly when to stop, and secondly, all the chips when drilling the end will simply fall down, and you will not need to sweep or blow them out with a vacuum cleaner, which is very inconvenient.

So, take a drill, attach a wood bit (50-54 mm) to the chuck and start drilling from one side, having previously marked the marked point. Do not try to drill through the entire canvas “in one go.” Firstly, the depth of the crown itself will not be enough, and secondly, the teeth of the crown will become clogged with sawdust, the crown will get very hot and burn the wood, and the deeper, the stronger. All we needed was a fire!

Having drilled 4-6 mm, without turning off the drill, pull it towards you, removing the crown from drilled hole. There is no need to turn on the reverse and generally make sudden movements. Everything should happen smoothly but confidently.

Clean the teeth of the crown from sawdust. Be careful, it can be very hot! It all depends on the material of the door leaf and the degree of its humidity. The denser the material and the moister, the more the crown heats up. But the crown with blunt, ground teeth heats up the most. Never use this! Buy a new one is my advice.

Having cleaned the teeth of the bit, and allowed it to cool if necessary, immerse it in the same place where it was removed some time ago, and continue this important mechanical operation to obtain the hole we need so much. As I already mentioned, the crown, due to its limited depth, will not allow the canvas to pass through. Having drilled halfway, you should go to the other side and repeat the entire operation again. You need to be careful here. When approaching the middle of the canvas, do not press too hard, let yourself enjoy the last seconds of this exciting process! Otherwise, you risk the bit going through and hitting the door leaf hard with the drill. But we don’t want to scratch it or leave a dent, right?

Drilling a hole for the latch

Let's move on to next stage. We remove the bit from the drill chuck, not forgetting about it elevated temperature. We clamp a feather drill with a diameter of 23 mm into the chuck. Pay attention to the photo. It shows that the drill is stamped with a size of 25 mm. But rest assured, no deception! I just didn't have a drill required diameter, and I used a 25 mm “perk”, having previously ground off its edges with a “grinder” to the desired diameter. Here's a little trick, take note.

You need to drill strictly perpendicular to the end of the door leaf. At first I thought it was very difficult to control. I mean, perpendicularity. But then I realized that it was easy to do, just by observing how smoothly the drill selects the circle. This is especially noticeable at the beginning of drilling, and having gone a little deeper, you can hardly worry that the drill will deviate from the specified course. But this does not mean at all that you can relax and look not at the drill, but at a cat covered in sawdust passing by.

Installing a latch for an interior door

Well then! The drilling of the holes is completed, now you need to recess the latch bar into the end of the door leaf so that it is “flush” with the plane. Professionals do this using manual milling machine, but not everyone has one, so you’ll have to work with a hammer and chisel.

Insert the latch into the hole and trace it with a sharpened pencil. To ensure that the strip stays in place while tracing, I usually immediately drill holes for the fastening screws and lightly tighten them, fixing the strip. Having traced the bar, remove the latch and take a chisel. Need I say that the chisel should not just be sharp, but very sharp?!

This article will describe the work performed to install latch handles on interior doors, which are the most popular in use today.

The latch handle has the following design.

The visible part of the handle may be perfect different types and it might look like this:

Or this way:

All such latch handles mainly consist of two parts, the handle:

and latch:

Each of these parts of the latch handle requires a separate insertion into the blade.

There are different types of such latch handles on sale, with a latch that have an additional mechanism installed in the handle itself, which allows you to lock the door from the inside, and from the outside on the handle there is a key holder that allows you to lock the door. There are also such handles and they cannot be locked without a lock. Latch handles from different manufacturers have various design features that cannot in any way affect the process of inserting into the canvas itself. Such handles have a latch on the inside, so the entire process of installing the latch handle is the same for everyone.

Therefore, if there are any differences, you shouldn’t have much doubt because of this and you should pluck up courage and start doing the work. And you should start with preparing the tools.

To do this, we will need tools to work.

• Screwdriver or hand drill.
• A crown with a diameter of 50 mm for wood.
• Made with size 23-24mm on wood.
• Pencil
• Chisel
• Hammer

In order to make the process of installing the latch handle into the door leaf as easy and quick as possible, you can purchase a special kit in specialized stores.

We begin to install the latch handle

1. In order to begin installation, you must first make markings on the canvas for drilling. If you purchased a special kit for inserting such a latch handle, then this kit already contains a marking diagram.

If you do not have such a diagram, then the markings can be done manually. To do this, we make a mark at a distance of approximately 1 meter from the bottom of the door leaf, then along this mark we measure 60 mm from the edge of the door leaf and make a mark for drilling, as shown in the photo.

2. On the side of the door leaf we also find the center and make a mark for drilling.

3. Next, take a chisel and for the front plate of the latch on the door leaf, hollow out a recess equal to 3 mm. It is better to drill out the center of the thickness of the door leaf with a slightly thin drill, so that later you do not have to make the marking again.

4. Using a crown with a diameter of 50 mm, we make a through hole. Through hole on the door leaf it is better to do it on both sides so as not to damage the leaf.

5. As a result of the manipulations performed, we will get a hole.

7. As a result, we get several holes on the door leaf.

8. Insert the latch into the hole on the side of the door leaf and screw it.

Using a special key that should be included in the kit or any thin and flat object.

Press the tongue in the hole.

and remove the handle.

10. After the handle, remove the decorative cap and expose the mounting holes.

12. Insert the other half, and then tighten both halves of the handle with the screws that come with the kit.

14. Cover the door leaf and mark the place where the tongue touches the jamb, in this place we hollow out a recess for the latch tongue.

15. A plastic pocket must be installed in the hollowed-out recess.

16. Place a metal plate on top of the plastic pocket and screw it on.

As a result of the work carried out door handle latch installed, the door is now ready for use.

Similar articles

At what height should I install the handle for an interior door?

The handle is an important part of the “pie” of an interior door, because the comfort and ease of use of the entire structure will directly depend on the correct installation and selection of it, and the “Dverka” interior door hypermarket will help with this. Most manufacturers offer doors for installation with existing handles and other included fittings.

The height of the handle in this case is standard and, in accordance with GOST, is 100 cm from the floor.

If the handle is not installed, models may or may not have slots for its attachment. In the second case, in the area of ​​intended fixation there is a special beam that allows you to install the handles and lock quickly and easily.

Here the height is determined independently, but the “limit” of indentation up and down should not exceed 10 cm.

A height of 100 cm is aimed at a person with a height of 170 cm. But given that this parameter can vary significantly, the best option is to purchase a door without fittings and marked grooves and secure the handle in the place where the best way will suit everyone living in the house.

Peculiarities

To finally decide on suitable height, you can adhere to the following rules:

• By the wrist. You need to come close to the door, lower your arms along the body. Make a mark at wrist level and step back 20 cm.

  The resulting height will optimally suit the person taking the measurements.

• At the elbow. Everything is simpler here: when approaching the door closely, the notch should be made at elbow level.

If you use both methods at the same time, the result should be approximately the same.

There is no need to make similar measurements for each door. It is enough to place a mark on one, measure the resulting distance and measure it on other interior doors in the house.

Pen in a child's room

The height obtained as a result of the above measurements for adults will not be suitable for children - the child will not reach the handle.

On the other hand, an additional groove will negatively affect the aesthetic appearance of the structure. The best option– use the push mechanism of the handle and attach a cord to it.

The child pulls the cord and the door opens without difficulty. When children reach a suitable height, the lace is untied.

It is worth considering that the correctly selected height of the handle is not the only important point.

Installing a mortise door handle

The element itself must be of high quality and reliable, easy to press. Especially for children. It is worth checking this point during the purchase. Only in combination with the quality of the product correct fastening will ensure ease of use of the interior door.

Expert of the hypermarket of interior doors “Dverka” http://www.dverkadverka.ru Victoria Zakirova

How was the handle on the front door secured?

All the handles on the door, when working, have the property of stunning and breaking.

Their renovation is not that weird and it will also apply to those taking it for the first time.

There are two ways to fasten a door: a screw, through a recess, and screws - self-tapping screws. Therefore, repairs may not be expensive and it does not require a huge amount of effort to use.

Which tool should I stick with before I start repairing the handle?

First you need to buy a set of screwdrivers or screwdrivers and bits.

By the way, it will be much more convenient and faster to make fasteners.

You will also need a set of screws.

Fixing a broken handle attached to a fork

By connecting two equal parts of the handle on both sides of the door.

This applies to spherical or conical products.

For types provided by the carrier, the elements are installed separately. This means half is broken, then it is repaired and the other is in place.

The handle is then removed as the door opens, keeping one hand halfway and the other in the opening.

All design details must be entered manually.

The handle half is then detached to reveal the fork set to the desired length.

How to Install a Latch Door Handle

In the same way, the entire structure turns back, here it is purely without a special tool.

Technical repair mechanism fixed in the form of brackets

In this case, you will need to buy a screwdriver or a screwdriver. It should be noted that transverse bolts are better and stronger than straight bolts.

The door handle is moved to cover the old grooves. Then, on the opposite side, two pairs of bolts are attached to the new holes.

Press firmly so you don't have to slide.

The tops are also installed using screws - screws with drilling into the new gutters. The overlay can be attached as a square or diamond. At the end of the work, the application is pinned.

Characteristics of replacement of small parts parts

When replacing a spring piece, the new piece is compressed tightly at the top, the veneer cap is installed, and the veneer ring is attached and connected to a screwdriver.

Then the rotating mechanism is delicately screwed in, followed by the introduction of a spring element into it.

The button is turned by a key.

In cases where the cake repair is not successful, it is much easier and cheaper to buy a new product.

Home »Inside» How to open door lock keyless

How to open an interior door lock without a key

Sometimes it happens that the inner door is closed and the key is missing.

You don't want to break the gate leaf, because it's quite expensive, and calling a repairman will additional element costs. So, how to quickly and safely open a door without a key to the design itself?

For what reason can doors extinguish?

Interior door lock

Before you start opening the neck structure right away, you must state the reason why it was destroyed.

Typically, this situation may arise for the following reasons:

• The lock in the handle is simply stuck or it has turned off.
• The latch is locked.
• The jammed tab located in the locking mechanism is stuck.
• On the other hand, there was a key in the cavity, which prevents the lock from being opened.

If you want to pinpoint the cause, you need to use a wide screwdriver.

With help in different places the door leaf rises. You have to pull it out a little and then it becomes clear where it is. Once you find an error, you can fix it.

Defective latch - what to do?

Typically, bolt failure causes an unauthorized door lock.

This item may not move completely. Even when you press the handle all the time, the tongue keeps running out. If the door is too attached to the frame or slammed shut, they can no longer open.

If so, you can do the following:

1. Using a simple screwdriver or other hard object, gently squeeze the design fabric from the box and gently lift it up as you do so.
2. In addition, to eliminate the possibility of such situations occurring in the future, it is a good idea if you want to spin the lever and see what is wrong with the tongue.
3. If necessary and option, it is better to replace the wrong product with a new one.

The language was not successful

There is also a situation in which the door structure of a door that is locked does not open after repeated use.

Even round handle does not have an additional latch, but the lock cannot be opened in the usual way, then the cause of the failure is most likely the language.

To solve this problem, you can use a sharp tool that easily fits into the gap between the frame and the door.

Then, to open the interior door lock without a key, you must follow the steps shown in:

1. Carefully insert the ruler into the slot, plastic card, office material or regular knife.

   Orientation to the part of the door on which the door handle is installed.

2. The tool used to open the tool should be slightly tilted and pressed.

   How to install a handle on an interior door: Photo.

   It needs to be pushed so that it can come into contact with the cut part of the tongue.

3. Angle a knife or other improvised device against the door leaf while the tongue is completely hidden in the lock. During the implementation of such measures, the handle should be in a lower position than in the figure, and the wing should be extended in the direction in which it normally opens.

If you follow all the rules above, your keyless door will open effortlessly.

Locks on the internal door: their main functions

Before opening a door handle without a key, it will not be superfluous if you know what functions such mechanisms have.

Only with everyone necessary knowledge and the skills to solve this problem will be much easier:

• Modern manufacturers could not ignore unauthorized stagnation at the doors. That's why they created a special door lock that has a lock on one side and a special opening page (button) on the back.
• If there is a moment when the door urgently needs to be opened without using a key, it is enough to insert a hard, rigid object (for example, an anchor) into the hole to open the mechanism.
• If there are doors with glass frames, then in the case of a ridge, you can carefully remove them and enter the room.

The situation could be big.

But if you can't handle the blocked lock yourself, it's better to call professional master, which will solve the problem in a matter of minutes.

Add a comment

Installing a handle on an interior door with your own hands - instructions on how to install the handle

Interior doors and fittings for them, including handles, are sold separately.

Accordingly, there are no holes for installing handles in the interior door. This happens for the reason that the handles, although standardized, are still different in design and installation dimensions. Here you can do it in two ways: either call a carpenter, or install handles on the interior door yourself.

So, we install the knob handle in the interior door. This is the most common type of handle, in my opinion, the most suitable and convenient for interior doors.

Before you begin installing handles, it is advisable to remove the door from its hinges.

If there is no one to help you, then you don’t have to take it off. But you should prepare a chair or stool so that you can fix the door, i.e.

she became immobile.

To install the handles, you will need a drill, a point drill, a ruler (preferably a square), a hammer, a chisel and a crown for large holes (see.

photo she is red).

Fig.1. To install handles on an interior door, you will need the simplest tool that is found in every home: a drill or screwdriver, a chisel, a feather drill with a diameter of 23 mm or a Forstner drill, a wood crown with a diameter of 54 mm.

First of all, we decide on the installation location, or more correctly, the installation height of the handles.

There are no strict restrictions on this matter. Typically, the installation height of the handle from the floor ranges from 1 to 1.2 meters. This height is sufficient for both adults and children.

They are different for different pens. In addition, they depend on the thickness of the interior door.

Also in the instructions, as a rule, there is a template for installing handles, where all the geometric parameters are indicated. We will be mainly interested in the dimensions of the holes for the pawl, the handle itself and their relative position. The diameter depends on these dimensions feather drill and crowns.

Therefore, you need to buy the necessary tools after purchasing the handles.

It is important to note that the drill and bit must be purchased with a diameter equal to the diameter of the hole in the instructions for installing the handles. If you use a larger tool, there is a high probability that decorative overlay will not close the hole. If it’s smaller, the handle simply won’t fit. At the same time, redo the holes for larger size, very labor-intensive and problematic.

It’s much easier and faster to do everything correctly right away.

Now you can directly begin installing the handle on the interior door. To do this, holes are marked for the handle itself and the pawl. For these purposes, it is convenient to use a ruler as in the photo.

Fig.2. Relative to the end of the door, the handle can be shifted by a distance of 60 - 70 mm.

At this distance, mark the place for the hole for installing the handle.

Fig.3. First, drill a hole for the handle.

To avoid burrs and chips on the door, proceed as follows. First, drill a hole with a drill with a diameter of 5-6 mm. Then, using a crown, an incision is made on one side of the door with a depth of at least 5-10 mm. Then a hole is drilled with a crown on the other side of the door.

Fig.4. At the end of the door, at the height where the center of the hole for the handle is, mark the center of the hole for the latch, and use a feather drill to make a hole.

The latch has a pad 2-3 mm thick. To ensure that the door closes well, a groove is cut out under the platform with a chisel. It is convenient to first drill a hole, then insert a latch and mark the groove along it, then use a chisel to cut it out.

After the holes are ready, insert the dog and trace it with a pencil.

And using a chisel we make a groove. This groove is necessary so that the dog's platform is flush with the door and does not interfere with opening and closing.

Fig.5. The installation of the handle begins with the installation of the latch. It is inserted into the groove and secured with screws that come with the handle.

You should tighten the screws carefully and do not tear off the notch for the screwdriver. To simplify screwing, you can pre-drill holes for self-tapping screws with a drill with a diameter of 3-4 mm.

This groove can also be made using a router. But for this you need to first make a template, which is not advisable for a “one-time” installation of handles.

After the preparation is completed, install the handle on the door and tighten the screws.

Fig.6. Final stage- This is the installation of the handle mechanism.

One half of the handle is installed in the latch groove. The handle halves are connected with screws.

Installing a door handle-lock on an interior door

It is important not to overtighten the screws, otherwise the handle may jam.

As you can see from the description, installing handles on an interior door is very simple. It is important to take your time and make the correct markings. After that, special drills are used to make holes for installation, a groove for the latch is cut out, and the handle is installed in place.

On average, it takes about 20-30 minutes to install the handles.

Home cosmetics

Install the handle on the interior door yourself

It is difficult to imagine how to use an internal door without such a mandatory attribute as a handle.

At first glance, its installation may be difficult. However, if you take the task seriously, you can independently manage the availability of the necessary tools and materials and the proper organization of work with this task. In the material presented, let's see how the handle is installed on interior door.

Types of handles

There are several types of cranks that are suitable for insertion into an interior door:

• rotary;
• with pressure mechanism;
• without locking mechanism.

Stationary handles that do not have mechanical work, allow the door to be opened by pulling.

When it comes to pressure systems, these roller blinds are designed in a lever style. In the process of pressing such a handle, the locking tongue moves inward, which allows you to open the door.

What is an oval handle door handle? Installing this system allows you to open the door without pressing the handle. Due to the circular shape of the handle, the operation is performed by turning the handle. The design can be equipped with a locking button, which allows you to lock the tongue of the locking tongue.

This way the door can be locked from the inside.

Tools and materials

What does it take to install handles on an interior door? Self-assembly may require the following tools:

• Measuring measuring tape;
• pencil;
• Manual or electric drill with a pen-shaped attachment;
• screwdriver;
• chisel for wood processing;
• hammer.

Inner door handle height

Before inserting the lock into the interior door, you must determine the optimal location for installing the handle.

To do this, it is enough to simulate the opening of the door to think about what height is most suitable for each individual user. As practice shows, the right decision is to place the handle on the internal door at a distance of at least 1 meter from the floor plane. The images presented are optimal for both adults and children.

Cutting holes for handle

After you find necessary tools and have determined the location of the building, you can proceed directly to creating a hole for installing the mechanism.

First, mark the height of the future handle on the plane of the door and its end. This is necessary to determine the exact location where the hole will be punched using a drill for a double-sided structure.

In order not to interfere with the calculations, it is enough to take the locking mechanism, and then, using a tape measure, we measure the distance from its eye to the visible edge.

The parameter must be marked at a pre-selected height on the door leaf. Once the appropriate markings appear, you can continue selecting the appropriate drill material.

At the end of the holes you need a diameter on the plane and at the end of the gate leaf, here you need to attach the opposite parts of the handle structure.

If the thickness of the plane does not allow installation, excess wood should be removed using a chisel. Then you need to scrape the fabric from both sides until the handle engages.

Bolt assembly

Once the previous work is completed, the latch should be installed in the prepared hole. Installation of handles door handle on an interior door assumes that it is attached to the door leaf in the open hole using fasteners that are attached to the product set.

It is appropriate to work with a screwdriver.

How to install a handle on an interior door

However, in the absence of the latter, you can use a regular screwdriver.

After strengthening the key part of the structure, he for a long time includes a core that is reinforced with a screw. To avoid problems with the basic assembly, the key must be inserted in advance, moving the mechanism locking mechanism to the closed position. Only then should the screw be tightened.

Installing a door handle on an interior door

Direct insertion of the handle into a pre-assembled structure is the most simple step work.

It is enough to insert the square rod into the corresponding hole in the locking mechanism.

The next step is to secure the handle with a buckle on one side of the door. To do this, you can use self-tapping screws or use zip ties. Once the first handle has been successfully assembled, similar operations must be performed with the other part of the structure, which must be installed on the back side of the door leaf.

This will establish a connection between the two elements of the system.

Installing the Keypad Insert in the Door Frame

To install the handle on an internal door, it is considered ideal, you need to make a corresponding hole to fit into the locking part of the lock in the door frame.

Do not use errors in calculations that allow you to use toothpaste on the tab along the vertical edge. When the door leaf is closed and the handle is released, the blocking element is connected to part of the frame.

The remaining toothpaste label will tell you where to make the hole under your tongue.

Using the method described above is optimal solution for determining correct location panels. Experts also resort to this root cause.

The formed imprint from the protruding tongue of the neck should guide a stable outline with a pencil. Then use a drill and chisel to enter the hole in the plug, then use a metal plate with the hole.

In advance, you will also need to place holes for fasteners to secure the plate to the door door.

When you have created all the necessary holes, simply secure the slab in the appropriate section. To fit tightly to the door cover, metal element must be screwed tightly to the wooden surface.

At the end

So we looked at how the handle was installed on the interior door.

This material provides an example of how to cut a simple mechanism into a wooden plan. Now you have enough knowledge to solve your problem yourself, without resorting to external help.

It is difficult to imagine an interior door without such an attribute as a handle. It may seem complicated to the average person self installation handles on the interior door, but all doubts are dispelled if you approach the matter correctly and with a positive working attitude.

What types of pens are there?

In nature, there are three types of door handles:

• stationary mechanism;
• with a push mechanism;
• with a turning mechanism.

Stationary handles do not have a locking mechanism. The operating process of the door is carried out through the action of force from itself or on itself.

The push type has a lever-operated shutter that, when pressed, pushes the tongue inward, allowing the door to open. The materials for its manufacture are most often the following: ordinary steel or a stainless steel sample, brass, aluminum or silumin, which combines not only part of the aluminum, but also a zinc alloy. For lovers of comfort, the most acceptable option would be a sample made of brass. Material of this origin perfectly maintains a temperature similar to the surrounding temperature, which does not cause unpleasant and sharp sensations of cold upon contact.

Types of door handles

Representatives of the rotary type are similar to push ones, but do not have a lever. Thanks to them round shape The lock comes off by turning, not pressing. This is where their name comes from - rotary. There are several examples of this type:

• models with conventional snap mechanisms;
• a device that incorporates a latch combined with a latch and a simple-format lock;
• A model that includes an additional locking latch.

Another sample of rotary handles is being produced, the additional attribute of which is a button designed to block the door. This is a convenient moment for privacy rooms, including the parent’s nest. The only negative nuance can be considered the inability to open the door without free hands, which cannot be said about lever types.

Differences in installation work

The most simple option A stationary sample of handles is considered for installation. This product is attached directly to the door leaf. Screws in the form of a curved bracket are used as fasteners. When choosing a material for fastening, it is necessary to take into account the massiveness of the door, since their ratio is directly proportional to each other.

Installing a handle on an interior door using a push or rotary mechanism is a little complicated, the reason for this is that to attach them it is necessary to immerse the lock part of the product in the door cavity. To do this, it is necessary to violate the overall integrity door design, which leads to an expansion of the list of tools used and the expenditure of a little more time. This is what gave them the name – mortise.

Handle installation

What is needed for the job?

Before you get started, you should definitely make sure that all the tools necessary for the job are available. This will certainly save a lot of time, effort and maintain the created working spirit.

During work you will need the following equipment:

1. Pencil;
2. Centimeter or tape measure;
3. Ruler in the form of a square;
4. Drill;
5. A set of drills, including a feather drill;
6. Chisel;
7. Screwdriver;
8. Bit;
9. Hammer.

You need to make sure everything is working properly electrical appliances, outline the scope of work, adjust the lighting to the proper level.

Place for the handle

You can insert the handle into the door yourself only when the door is completely immobilized. This can be achieved in two cases: by removing it from the hinges, and if this is impossible, you need to substitute a foreign object that can hold it at rest (for example, a stool).

Since overhead handles are very easy to install, there is no point in considering the process itself. In addition, the use of mortise models has become popular. It is from their example that one should learn and gain experience.

Initially, we decide on the location of this unit. This refers to the installation height of the interior door handle. Often, its norm varies within 1 meter from the floor surface - this is the most optimal footage, suitable for both a child and an adult.

It is necessary to take into account the location of handles on adjacent doors, if any. It is also worth paying attention to the texture of the door itself, checking for the presence of fittings on the surface, or other distinctive irregularities and protrusions that may affect the location of the handle.

Having marked the height point on the door leaf, draw a horizontal line using a pencil and a charcoal ruler. We retreat 60 mm from the edge of the door, revealing the location of the central hole. Duplicate the data to the opposite area of ​​the canvas.

Next, you need to set the location for the tongue from the lock. To do this, you need to move the horizontal line to the end of the door and find the center point. After which the locking plate is applied and outlined at this point.

Making holes for the latch and handles

After carefully installed markings, it's time to use the drill. With its help, the necessary holes will be made without much difficulty. When drilling, you should use a feather drill. It will allow you to more accurately and clearly make holes for connecting handles in the form of a square.

Important to remember! You need to buy equipment for such work after purchasing pens. This is justified by the fact that the parameters of each product are different and may not correspond to the available drills.

To work in the end part, a drill of a feather model is also used. The recess is made similar to the length of the snap mechanism.

Holes in the door for the handle

Then, having deliberately measured the thickness of the lining, we remove the excess with our own hands, using a chisel. We clean everything until the strip can fit tightly and completely into the door leaf.

Place the latch in the hole

Once the latch location is ready, you need to place the occupant there correctly. Difficulties will not arise if you adhere to a clear sequence.

The first thing to do is to place the locking latch in the groove that was originally cut. Next, we screw it in with two screws that are included with the product. This must be done from the end area.

After strengthening work has been carried out on the lock, the core part is immersed in it, which is secured thanks to the long screw part. A screw is placed in the decorative area belonging to the lock escutcheon.

There is a little trick to remember. For easy and smooth, and most importantly correct insertion of the core, you need to place a key in it, and the tongue must be directed to the bottom, to the closed position, and only then tighten the screw.

Installation work of handles

Handle technology general design, perhaps one of the most simple tasks, done during the entire installation period. A square-shaped rod must be inserted into the resulting hole for the handle. The next step is to fix the handle on one of the sides of the door. A couple of methods can be used for strengthening work. The first is characterized by a method of fixation using self-tapping screws. The second one welcomes the method by which screwing is carried out in the presence of ties.

Installing door handles

When the first handle has been successfully installed, you need to do the same with the second. In this way, we will establish communication between both components.

Introduction of a sheer dog plate into the design

To properly install the dog plumb plate, you need to find and mark the middle of the hole on the frame box. At home, it is customary to use toothpaste for this, but another similar ingredient can also be used.

With one hand we press the handle and hold it in this state. Meanwhile, with the other hand, apply the paste to the tip of the dog along the entire vertical edge. Then you should close the door and release the handle. At this moment the dog will come into contact with the box part.

Press the door handle again and bring it to the open position. Opening it, we find that the paste has left traces. This area will be the mark for embedding the plumb plate. This method is the most reliable and error-free. Even experts use it.

We outline the resulting imprint from the protruding part of the latch with a contour. Using a drill and a pen, we need to drill a hole for the dog. It is also necessary to make openings for self-tapping screws that act as a fastening system.

Finishing preparatory work, we screw the lining in the area where the screws are located. To ensure a tight and soft fit of the door leaf in the opening, the plate located on the opposite side of the latch is subjected to a pressing process.

From the above material, the following instructions emerge:

1. We determine the attachment point of the handle with the lock;
2. We measure the locking units and mark them on both sides of the door;
3. We make recesses to place the locking apparatus and the handles themselves;
4. We first install the core, and then the handles themselves;
5. We identify the location of the vertical plate and make a recess;
6. on self-tapping screws.

After similar work You will no longer have questions about how to install a handle on an interior door. Having done this once, you can easily repeat all subsequent installations with the same success.

One more point should be taken into account. Handles with an embedded lock should only be installed on doors whose material will subsequently be exposed to painting work. Good luck in your work process!

Apartment renovation happens quite often with the installation of windows and doors. But modern fashion trends, in Lately, sometimes force us to completely abandon doors, for example, in the kitchen. If the purchase has happened and you have installed an interior door, then next you need to install door handles. IN this material We will walk you through the steps to install a door handle with your own hands.

What kind of door handles are there?

Stationary, motionless;

Push-type, with lock;

Rotary, often the lock in such handles is built inside.

When entering a building materials store, you need to choose door handles according to certain criteria:

1. Appearance and the unlocking element of the handle. Typically, the handle is characterized by an oblong shape, if the handle is equipped with a pressing mechanism, or a ball-shaped handle with a turning mechanism.

2. What is the handle made of and how does it feel to the touch. The door handle can be made from either wood or metal materials. As a rule, this is aluminum, brass, and several other alloys. Also, handles can be made of stone, plastic, or glass. The most common, of course, is a metal handle with a wide choice of coatings, for example - chrome-plated, nickel-plated and others. The coating affects not only the kinesthetic personal sensations of a person, but also the color and durability.

What kind of door handles are there?

Wooden door handles

3. Does the handle have a lock? The handle can either have a lock or be without it. Locks can be built into the handle; usually, you will remember such a handle as the round type. On one side, such a lock is opened with a key, on the other it has a latch.

Attention! In hardware stores, there are handles for the left hand and for the right. Before purchasing, it is important to tell the seller what kind of pen you need.

Door handle diagram (video)

To install a door handle, you will need certain tools:

1. screwdriver;
2. hammer;
3. chisel;
4. bit;
5. drill with drills, must be a feather drill;
6. tape measure, triangle, pencil.

We will analyze the installation using Apecs handles. They are very popular and most common on the Russian market. These handles are made of brass; this material is also the most common in handles today. It is easy to handle, not expensive, and how pleasant it is to the touch has already been appreciated by many owners of such pens.

Apecs Door Handle

Below is step-by-step recommendation regarding the installation of door handles that have a latch but no locking mechanism. It must be taken into account that the insertion of a round type door handle does not have any serious differences from the installation that we give as an example.

Apecs Door Handle

The principle of the mechanical operation of a door handle is simple: the handle turns, the lock tongue goes into the door. For this reason, the very first step will be to create holes for the handle, as well as cut out a groove for the tongue and the rotary mechanism. First you need to decide on the height at which the handle will be located. Professionals advise making a mark at waist level, taking into account how much your arm will bend when turning. As a rule, this is a meter from the floor.

Attention! By technical specifications, which are regulated by GOST 6629-88, the height of the door handle must be exactly and exclusively 1 meter from the floor level. But if your house is your own, choose any height convenient for you.

Installation height of door handles and hinges

It must be taken into account that when installing handles in rooms where bedrooms are located, the handles must be installed at the same height. Otherwise it's easy to get confused dark time days for residents.

But there are also cases when the door already has connectors for handles, but they are located only at certain points. In this case, if you decide to place the handle in a place other than that provided by the manufacturer, then bad consequences are possible. Also, if children will live in the house for any length of time, the height of the handle must also be lowered to at least 75 cm from the floor.

As soon as you have resolved the issue with the height, you must immediately draw a line horizontally at the measured height. A simple ruler will help you with this. Mark the center of the hole 6cm from the door edge with a dot or a circle. Mirror the markings to the other side.

The next step will be marking the lock tongue. To do this, mark the center at the end of the door between the future door handles. You should attach the striker plate and then carefully circle it. Before installing all the elements, you need to erase the pencil as much as possible, because after installation it will be difficult to do this. Leave only the elements that you understand for reference.

Having made markings on the door, you need to start drilling holes for fastening the door handles. Making them yourself is not difficult. Using a drill or a pen drill, make suitable holes to connect the door handles with a square.

At the end of the door, similarly, using a drill and a feather drill, make a hole, the depth of which will be equal to the length of the latch mechanism. Then, using a chisel, having measured the thickness of the lining in advance, remove the excess elements to a distance that will allow the strip to fit completely into the door leaf. This whole process is clearly demonstrated in the video.

Once you have installed the latch, you need to install the door handles you purchased. Initially, the square from the kit is inserted. It will move the tongue when you turn the handle.

Then, remove the trims, which are round, threaded, and decorative. They have inside There is a special thread in the base, which is screwed to the door using screws.

DIY door handle installation

Now you need to properly secure the locking screw of both handles; a special hex wrench will help you with this, usually included in the kit. The locking screw itself is needed to firmly press the door handle to the turning square, while at the same time preventing any slipping during operation.

DIY door handle installation

Preparing the door frame

The last step is to position the door handle correctly. Those. make installation of the mating part of the latch. To do this, you need to lubricate the lock tongue with oil, close the door, and make a mark with the tongue door jamb, in a simple way, scribble. At the same time, make several test openings and closings with the handle. Then, you need to attach the trim, which should rotate directly to the jamb, and trace it along the contour, including the inner hole.

Using a drill, you need to drill a hole for the locking tongue of the latch, and the rest of the part needs to be deepened using a chisel or chisel. Make the depth 2 millimeters, or 1, depending on the depth of the bar itself. All that remains is to fasten our plank with two screws. Use an awl to make marks for the screws, and use a drill to drill holes of the required diameter accordingly. Using a screwdriver or by hand, secure the strip in the door jamb.

Cut the corresponding holes in the door for the door handle

It is difficult to imagine how to use an interior door without such a mandatory attribute as a handle. At first glance, its installation may seem complicated. However, with a serious approach to the task, the availability of the necessary tools and materials and proper organization you can handle the task yourself. In the material presented, we will consider how to install a handle on an interior door.

Types of handles

There are several types of handles that are suitable for inserting into an interior door:

• rotary;
• with a push mechanism;
• without locking mechanism.

Stationary handles, which do not have a mechanical part, allow you to open the door under the influence of pull. As for push-pull systems, the latter have a lever-style shutter. In the process of pressing such a handle, the lock tongue moves inward, which allows you to open the door.

What is a lock for an interior door with an oval handle? Installing such a system allows you to open the door without pressing the lever. Thanks to the round shape of the handle, the operation is carried out by turning the holder. The design may include a locking button, which allows you to fix the tongue of the locking mechanism. This way you can lock the interior door from the inside.

Tools and materials

What does installing handles on interior doors require? During self-installation The following tools may be needed:

• pencil;
• a hand or electric drill with an attachment in the form of a feather drill;
• screwdriver;
• chisel for woodworking;
• hammer.

Interior door handle installation height

Before inserting a lock into an interior door, you need to decide on the optimal location for placing the handle. To do this, it is enough to simulate the opening of a door, think about what height is most acceptable for each individual user. As practice shows, the right solution is to install the handle on the interior door at a distance of at least 1 meter from the floor plane. The presented footage looks optimal for both adults and children.

Cutting a hole for the handle

Having found the necessary tools and decided on the location of the structure, you can proceed directly to creating an opening for mounting the mechanism. First, you should mark the height of the future handle on the door plane and its end part. This is required to determine the exact location where the opening will be made for the double-sided structure.

In order not to make mistakes in the calculations, it is enough to take the latch mechanism, and then use a tape measure to measure the distance from its eye to the visible edge. The parameter must be marked at a pre-selected height on the door leaf. Once the appropriate markings have been made, you can proceed to selecting a suitable bit for drilling holes.

Having made the openings of the required diameter on the plane and the end of the door leaf, here it is necessary to attach the opposite parts of the handle structure. If the thickness of the plane does not allow assembly of the product, excess wood should be removed using a chisel. Next, you need to strip the canvas on both sides until the handle fits tightly into place.

Latch installation

After all preliminary work has been completed, it is necessary to position the latch in the prepared hole. handles on an interior door involves screwing it to the door leaf in a prepared opening using fasteners that are included with the product. It is convenient to carry out the work using a screwdriver. However, if the latter is not available, you can use a regular screwdriver.

After strengthening the locking part of the structure, a core is built into it, which is strengthened thanks to the screw, long part. To avoid problems with installing the core, you must first insert the key into it by moving the locking tongue of the mechanism to the closed position. Only then should you tighten the screw.

Installing a door handle on an interior door

Directly introducing the handle into a previously installed structure is the simplest stage of the work being done. Here you just need to insert the rod square shape into the corresponding opening of the locking mechanism.

The next step is to fix the handle with fasteners on one side of the door. To do this, you can use self-tapping screws or use zip ties. As soon as the first handle is successfully mounted, it is necessary to perform similar operations with the other part of the structure that will be placed on back side door leaf. In this way, a connection will be established between both elements of the system.

Installation of a plate for inserting the lock tongue into the door frame

In order for the installation of a handle on an interior door to be considered complete, it is necessary to make a corresponding hole for the locking part of the locking system to fit into the door frame. To prevent errors in calculations, apply toothpaste to the tongue of the mechanism along its vertical edge. When the door leaf is closed and the handle is released, the locking element is connected to the frame part. The remaining toothpaste mark will tell you where to make the hole for the tongue.

Using the above method is the optimal solution for determining the correct location of the plumb plate. Despite the primitiveness of the method, even specialists resort to it.

The resulting imprint from the protruding tongue of the door latch must be drawn with a stable outline using a pencil. Next, you should use a drill and a chisel, with which you will make a hole for the locking pawl to fit in, and then a metal plate with an opening. You will also first need to make openings for fasteners to fix the plate on the frame of the door.

After creating all the necessary holes, it is enough to attach the plate to the corresponding area. To fit tightly into the box, the metal element must be firmly screwed to the wooden surface.

Finally

So we looked at how to install a handle on an interior door. This material provides an example of how to embed simplest mechanism into a wooden plane. Now you have enough knowledge to cope with the task yourself, without resorting to outside help.