Making a picture frame with your own hands: three simple ways. Do-it-yourself photo frames made of cardboard, paper, scrap materials on the wall with your own hands Beautiful frames made of wood

There is always the question of how best to glue a wooden picture frame. Frames with a figured profile are joined in a “mustache”, i.e. The ends of the parts are filed at an angle of 45*. Clamps for tightening frames when gluing have existed for a long time, but the strange thing is that they continue to be invented to this day.

Moreover, such clamps are designed by the craftsmen themselves, especially those who have to make a lot of such frames as part of their work. Apparently the only one universal clamp haven't been invented yet.

I don't make picture frames every day, and I usually use two methods. The first option is to tighten the parts using a special corner clamp, photo above. But this method has some inconveniences; the corner clamps that I use do not allow me to assemble small frames.

There are other fairly simple gluing methods. Making such a device takes just a few minutes. To work, you will need a flat square platform made of chipboard or thick plywood. Support bars are screwed onto two edges with self-tapping screws. Please note that during assembly, the bars should be at an angle of 90* relative to each other. For precise installation, use a metal square.

Next, we coat the frame parts that have already been prepared and sawed at an angle with glue and tighten them using two long clamps. When compressing, be sure to check all corners of the frame with a square. The photo shows how else you can check the correct assembly. Graph paper is placed on the device platform, and during assembly you can see how the parts fit in relation to each other. And also, so that you can use your device for a long time, place paper under the corners so that the glue does not stick to the site.

The other option is more like a professional corner clamp, although in fact it is also homemade. Four separate stop angles with flanges are used here. All four corners are tightened from the inside with elastic rubber, a tension rope or a cable. IN classic version all four corners are tightened with one bolt, and the stop angles are installed on four diagonal slats.

As for this particular product, the whole problem here is to make these very corners with sides. In my opinion, the methods listed in this article are quite suitable for making a small number of frames. There is another method, article. Although I repeat, craftsmen continue to invent corner clamps for assembling frames, everyone is looking for the most convenient option for themselves.

Photographs are a repository of a variety of moments. They preserve life itself. That is why always, even in the era digital technologies, people put on the table, place on the walls photos related to a particular event or person. I don’t want to put the memories that are dear to my heart into a template framework. Therefore, the decor of photo frames has always been, is and will be in demand. Decorating frames with your own hands is possible for almost everyone; it is exciting and makes you feel like a real creator.

You can use a cheap purchased frame as a basis for your work or cut it out yourself from cardboard.

Types of photo frame decor

• The first most common way to decorate a photo frame is to stick something on it. And this “something” is a boundless sea;
• paste over in decoupage style;
• paint in an original way using a variety of techniques;

• the frame can be sewn from soft materials;
• cover with knitted fabric;
• decorate with fabric;
• wrap it picturesquely with twine, various threads, braid, lace;
• made from tree branches;
• You can even bake it (from salt dough).

The list can be continued indefinitely; it can only be limited by the limit of your imagination.

Pasted decor

You can glue a lot to a frame, everything is determined by the taste and imagination of the master.

Buttons

Photo frames decorated with buttons will look original, especially if you choose them in the same color. However, this is not required condition. The desired color uniformity can be achieved using acrylic paint. For example, buttons coated with gold paint will transform beyond recognition an old photo frame that by a lucky chance did not end up in the trash bin.

Beads, rhinestones

Over time, such things accumulate in abundance in every woman. All this can become a unique collection of materials for decorating an elegant frame with your favorite photo with your own hands; it’s worth gluing them onto a pre-planned drawing or ornament.

Tip: you can use whole brooches, beads, beads, pearls, interesting pieces of glass, fragments of broken dishes, mosaic elements.

Natural materials

Tastefully executed frame decor in natural style always attracts attention. After all, we are all children of nature.

Coffee beans, lentils, acorns

Everything can go into action and create unique compositions.
Coffee beans will be useful to you not only for making an invigorating drink, they turn out to be an excellent material for decorating a photo frame with your own hands: they have a wonderful smell, an original texture, a noble color, and they do not spoil. The work won’t take much time either: it’s not so difficult to use a glue gun or PVA glue to tightly line a standard photo frame with coffee beans, which in its new guise is guaranteed to become a leading interior accessory.

Tip: to make your handmade frame smell fragrant, buy star anise and star anise and find a place for them in the overall decor.

Shells

This is one of the rewarding materials for decorating a photographic frame with your own hands. Need shells for decoration various shapes and magnitude. In addition to shells, it is appropriate to use interesting glass, sea pebbles and other finds made on the sea or river bank in inlay.

Paper

When creating an exclusive frame with your own hands, you can use paper, which under normal circumstances would face the sad fate of waste paper. Very original photo frames are decorated with paper tubes from newspapers and magazines that have served their purpose.

They can be either short (we stick them on the end) or oblong – we use them in a horizontal position.
Another decor idea: birch bark is a very impressive look natural materials. Cut a piece of birch bark into five strips. Four will become the actual frame, the fifth can be made into a stand.

Salty dough

You can turn an ordinary photo frame into a designer one using salty dough. Everyone has their own ideas: some will decorate it with flowers, while others will add the name of the child shown in the picture. But first you need to make this very dough: knead it from a glass of salt, two glasses of flour and water. Having achieved the consistency of plasticine, start sculpting your intended decorative elements right on the corner of the photo frame - this way the dough will take the desired shape at the base, and you can easily glue it to the right place. Place it in the oven for 20 minutes. Let it cool, glue it to the frame and begin painting with any colors. You can even limit yourself to one from an aerosol can. The final stage consists of varnishing (it is better to do two layers) and drying.

Childhood surroundings

If there are daughters in the family, the number of decorative hairpins and elastic bands increases exponentially. Cute trinkets, decorated, for example, with flowers, can get a second life when this idea is implemented. Cut flowers from tired rubber bands. The larger ones should be glued to top corner frames, place smaller copies below.

As a result, a real flower cascade. You can glue the flowers only on the top, leaving the bottom of the frame untouched. Having completed this process, place the work under a load for several hours. When the flowers are white, the remaining part of the frame free from decor should be covered with silver paint, or green if they evoke associations with a spring meadow.

Decoupage

Before starting work, prepare:

• a frame (not necessarily a new one, you can just get bored);
• a sheet of sandpaper;
• glue (if there is no decoupage glue, dilute PVA glue equal amount water);
• brush;
• decoupage napkins, cards.

After this, proceed to the decoupage process itself:

• Sand the old photo frame first. A new one, if it is not varnished, does not need to be processed.
• First, you need to cut out the desired area from a napkin or card, having previously measured the frame itself, not forgetting about the reserve required for processing the edges.
• Using a brush (or a sponge), carefully apply glue to the front side of the frame. Then place the prepared image in the desired place and smooth it, making sure that all air bubbles come out from under the pasted fragment. Do this starting from the center, gradually moving to the edges.
• Then, literally for two minutes, you need to put the frame under something heavy, for example, under a massive book.
• To remove excess pieces of tissue paper, run a nail file along the edge of the photo frame (pressure angle should be 45). In the same way, remove the remains from the central part.
• Finally, apply another layer of glue and set the frame to dry.

A rich assortment of decoupage napkins will definitely allow you to choose the means to realize your idea and create a unique piece.

Another option for decoupage photo frames

Add paints and varnish to the previous set of materials.

Bold and non-trivial

• People who value originality can even use a used bicycle wheel as a photo frame: select photos of a general theme, think over the plot, insert a photo between the spokes or secure with clothespins - original decor ready.
• There is no need to guess how a hunting enthusiast will react to a portrait presented to him in a frame made of spent cartridges. Of course, with sincere gratitude.
• Option for fishermen: attach hooks or brackets to the fishing rod, use twine or thin cable with original sea knots, hang frames with photographs on them, add a couple of floats.
• Even an ordinary one can become a creative photo frame glass jar: place a photo of the appropriate size in the selected container, decorate the empty space in it with sand, shells, starfish, LED garlands or any other surroundings close to the subject of the photo.

It is impossible to describe all the ways to decorate photo frames with your own hands: every day the ranks of lovers of this democratic type of needlework are replenished, new ideas are born, which, in turn, become an incentive for further ideas. The creative process never stops.

Master class “Wood frame for photos and paintings”

"For a family photo." Master Class

Zhbanov Alexander Semenovich, teacher of fine arts and technology, MBOU "Perkhlyaysksya OOSH" of the Ruzaevsky district of the Republic of Mordovia.
Purpose: Regardless of the style of our interior, wooden frames are the best decoration paintings or photographs, because wood is the most expensive and exquisite material. Thus, a wooden frame can not only decorate a picture or photo, but also improve the design of our interior. A gift in the form of a frame made of wood will bring warmth and comfort to your home.
The master class is designed for 6th grade students; it will be useful for technology teachers when studying the topic “Artistic processing of wood products,” and for creative parents.
Target: Making wooden frames for drawings, photos and paintings.
Tasks: Familiarize yourself with the species artistic treatment wood products, improve skills in working with wood, develop creative thinking, develop the ability to see beauty, cultivate diligence, and interest in arts and crafts.
Teacher's opening speech
Artistic processing of wood products is an amazing art and skill of working with wood. However, with desire, a little creativity and patience, almost anyone can create interesting decorative items. The main types of artistic wood processing are: wood carving, pyrography - burning wood, turning - turning various products from wood, painting on wood. Some means are also provided for wood processing. The most accessible and inexpensive are stains, beeswax, water-soluble paints, and varnishes. This simple set of tools will give the product a finished look.
Today we choose simple carving elements and water-soluble paints. But first of all, we need to manufacture the product.

During production wooden frame We will work with tools such as a hacksaw, hammer and chisel, and perform simple wood carving techniques. Let's practice connection techniques wooden parts using glue, let's do it decoration products. When working, we will strictly follow all the safety rules learned earlier.
To work you will need:
1. Wooden slats 250x50x10mm - 2 pcs., 350x50x10mm - 2 pcs.
2.Wood cutters
3.Watercolor paints, varnish
4.Sandpaper, glue

We chamfer (round) the edges of the slats. We use a cutter or an ordinary knife. Don't substitute left hand under the cutting tool!

Let's prepare all four slats.

Let's draw arbitrary wavy lines.

We cut out a shallow groove (stream). For those who have not used wood cutters before, I advise you to attend this master class. Here you will find the tricks and rules safe work. /blogs/jbanov-aleksandr/obuchenie-tehnike-rezby-po-derevu.html

Let’s make one “bank of the stream” flat.

It turns out to be a stream with one steep bank.

On one half of the slats (with a steep edge) we apply random grooves with an angular cutter, thereby imitating the bark of a tree.

This way.

All four slats are ready.

Let's study this drawing. Dimensions in millimeters.

Let's arrange the slats according to the drawing. Depending on the size of the photo or painting, the size of 50 mm can be reduced or increased. The cut end of the batten is placed on the clean surface of another batten and the location for the groove is marked with a pencil.

Use a fine-toothed hacksaw to make cuts (to the middle)

Cut out the grooves. This is done with a chisel or a flat chisel.

Thus, we get four grooves on the uncut ends of the slats.

Let's put it in places.

Turn it face down and mark the ends of the slats with the corresponding numbers.

We repeat the same work on back side.

You can check it.

It's time to use wood treatment products. We chose ordinary watercolor paints. Everyone has the right to choose the color themselves.

Let's go over it lightly with sandpaper.

Let's assemble using glue. The brand of glue can be different: carpentry, “Moment”, “PVA” and others. Coat the grooves with glue and press tightly. You can use a simple press (several books on top of each other)

The frame is almost ready to be used for a painting. And for photography you need glass so that the photograph is well preserved and can be easily replaced. To do this we use a window glazing bead.

We frame it with glazing beads on the reverse side. inner part frames, departing from the edge 6-8 mm. You can use glue or small nails.

From the same glazing bead we will make two small turntables.

Let's score

Let's give an aesthetic look

Cut a rectangle to size (thick cardboard, plywood, fiberboard)

All that remains is to come up with a device for the suspension. To do this, we will make two loops from the wire.

Using an awl or a thin nail, we drill shallow holes and “plant” them with glue.

Let's tie a secure thread

The teacher cuts glass. Paint it with clear varnish. The frame is ready!

Insert a photo.

Gift for a “wooden” wedding.

In this article we will talk about how you can make comfortable and beautiful photo frames with your own hands.

Each photograph is a unique phenomenon, preserving a piece of some emotion. So why not frame these images in unique frames?

Crafts - beautiful do-it-yourself photo frames from scrap materials: ideas, photos

To begin with, we suggest that you familiarize yourself with the ideas of what kind of photo frames you can make:

Photo frame made from burlap roses

Photo frame made of fresh flowers - short-lived, but beautiful Frames with knitted spirals











Extremely original idea- old clock as a photo frame

DIY cardboard photo frame: master class

To make a cardboard photo frame you will need stock up on the following things:

• Corrugated cardboard
• With a knife
• Pencil
• Glue
• Paper for decoration – absolutely any paper will do
• Buttons, shells, beads

You can start making:

• From a piece of cardboard need to cut out the front and back of the frame. It should look like this blanks, as in this photo:

• Now is the time to decide how much you need measure paper for decoration.

IMPORTANT: It is necessary to take into account that it will have to be folded inward. That is, you can’t do without a reserve.

• Now front part of the cardboard blank need to treat with glue, and then glue paper to it for decoration. Until the glue has completely dried, you cannot proceed to further steps.

• But after drying you can Glue the front and back parts of the photo frame together. Only the upper parts do not need to be glued, since a photograph will be placed through the top in the future.
• But that’s not all, because it’s necessary build a support for the frame. For this purpose, you need to cut out such a part from cardboard as shown in the photo below. You can make it out of paper and then glue it onto a cardboard base.

• All that remains is decorate photo frame of your choice.

How to make a children's frame out of paper: templates, diagrams with descriptions

Such a bright photo frame will surely appeal to children, especially girls. It will definitely decorate the interior of a children's room:

If you like this idea, you should stock up on the following: components to implement it:

• Paper - regular colored paper, gift paper, or even unnecessary magazines will do.
• The frame is made of wood, which can easily be found in a craft store. Or maybe there’s an old frame collecting dust somewhere in the house?
• Glue

IMPORTANT: Hot glue gun will also come in handy, it is especially convenient for beginners in needlework.

• Scissors or stationery knife
• toothpick

You can start:

• If you want to update the frame coating, you can do it now, having painted her.
• From paper you need cut strips.

• Then all the stripes are necessary fold in half.
• Now every strip is needed roll into a roll. This is where a toothpick comes in handy, although you can completely do without using one. ends each roll needs to be carefully glue.

IMPORTANT: Do not be upset if the blanks turn out well different sizes. It is even preferable that each roll be different from the previous one.

• As soon as there are enough bright rolls sufficient quantity, you can start working on them fixation on the frame. This is where a glue gun comes in handy. You can attach the parts randomly, but the strength of their pressing to the frame is required!

We would like to present to your attention another photo frame manufacturing diagram:

How to make an autumn frame in autumn style - golden autumn: templates, diagrams with descriptions

The easiest way to create a frame in honor of the golden autumn is Cover the finished frame with leaves. Leaves are needed first iron. Then they are recommended Place in hot water for one minute. However, not boiling! This will allow the leaves to lie better on the cardboard.

After fixing the leaves on the frame, you should send the craft under press With. You can then cover the surface with matte varnish.

If you want something not as familiar as leaves, you can decorate the frame acorns.

More a few ideas for creating an autumn frame:

How to make a beautiful felt frame: templates, diagrams with descriptions

The felt photo frame magnet is quite unusual and easy to make.

If you like the idea, you will need to buy:

• Hard felt

IMPORTANT: It is advisable that it corresponds to a thickness of 2 mm and dimensions of 13x26 cm.

• Tapes approximately 5 mm wide and approximately 3 m long
• Needles - one regular and the other with a wide eye
• Floss threads - it is preferable that they be the same color as felt
• Ready-made magnet or magnetic tape
• paper
• Scissors
• Ruler
• Toothpick or awl
• Colored pencils
• Coin

You can get started:

• On the back of the felt required to draw two squares. Each of them must have equal sides 13 cm.

IMPORTANT: Now is the time to take the coin. You should not ignore this stage if you want to get a rounded frame.

• Blanks can be cut out.

• Now is the time to get busy template for making a hole for the photo. In this example it is represented as a cloud, but in reality it can be any shape.

• Hole need to cut out.

• But, of course, without covering the cut area not enough! It will be useful for this overcast stitch with two threads. Fastening occurs on the inside.

• Now the template blank must be traced on paper. It is worth marking the outlines of the embroidery on it.

It's time to get busy ribbon embroidery! The green one should be cut off about 50 cm by inserting it into a needle with a wide eye.

IMPORTANT: Try to cut the end of the tape at an angle of 45 degrees.

• End ribbons follow fasten on the wrong side felt blank using a needle and thread.

• What follows in advance pierce the felt in the places where you plan to insert the needle and ribbon. The fact is that hard felt is too strong for a needle, so it is recommended to use an awl or, in extreme cases, a toothpick.

• Now it’s worth flashing the frame in the same way and blue ribbons.

• Next you need fold both felt blanks. They should sew with a blanket stitch using floss threads.

• Left stick magnetic tape on the back of the frame.

How to make a carved photo frame from wood: templates, diagrams with descriptions

Choosing the right wood for making a frame is already half the success. Very will look attractive products from cherry, walnut, ash, linden. If in the future painting planned, That optimal options will become spruce and pine.

IMPORTANT: It must be remembered that the softer the wood, the easier it will be for the craftsman to make patterns on it. This is especially important for beginners to take into account.

You need to make the frame as follows:

• From the die it is necessary cut blanks,the thickness of which will reach approximately 26 mm. Minimal allowances are needed.

• Now you need trim the edges, then glue the workpiece.
• Having drawn template for the pattern, it is worth attaching it to the tree. The pattern is transferred to the future frame.
• Contours outlining hole for posting photos, needs to be cut.
• It is also necessary to cut patterns.
• Now we need to designate rebate dimensions, intended for glass with a photograph.

IMPORTANT: It is worth following the symmetry of the marks.

• It's your turn milling.
• Now it's happening leveling using straight chisels.
• Can be done back of the frame.

We offer the following patterns. They are mainly used by craftsmen for making platbands, but they are also perfect for photo frames:

Patterns-1 for a photo frame made of wood

How to make a photo frame from plywood: templates, diagrams with descriptions

For a similar photo frame needed:

• Multilayer plywood minimum 10 mm wide
• Wood plywood saw
• Electric jigsaw
• Drill – can be either manual or electric

IMPORTANT: The most important thing is to have wood drills.

• Scissors, measuring instruments
• Stapler for working with furniture and staples for it
• Metal bracket or reinforced thread to fix the frame
• Grinding devices – fine-grained sandpaper or special grinding machines
• Woodworking varnish

You can get started:

• The first thing you need to do is transfer templates for material.

• Using a drill need to do several holes, and end-to-end.
• Now You need to place a jigsaw in the holes. They produce cutting out the pattern.

• Now it's time grinding.
• Next you can proceed to painting object.
• Now you can insert photo. If you wish, you can place it under glass. In this case, you will have to attach the back wall, securing it with a construction stapler or self-tapping screw.

How to make a photo frame from plinth: templates, diagrams with descriptions

To create such a photo frame needed:

• Pieces of wooden plinth
• Glue type “Moment” or “Adhesive nails”
• Stationery knife or knife for construction work
• Protractor or miter box
• Marker
• Ruler
• Acrylic paints, as well as acrylic putty for working with wood
• Cardboard – always thick

Operating procedure:

• First it is advisable to cut cardboard base, which will be slightly larger than the desired photo.
• Next you need to cut out another piece from cardboard - the front of the frame.

IMPORTANT: Each side of the second part should be approximately 5 mm smaller than the first.

• Now both parts need to be glued to each other.
• Then you need to measure 4 pieces of plinth. You need them with a miter box cut at a 45 degree angle. If you don't have a miter box, you can draw a corner on paper and then mark it on the baseboard with a marker.
• Now you need glue the panels to the cardboard base. If you don’t want to make such a base, you can simply glue the parts to each other.

• If there are cracks, they can be easily cover with putty.

• After the putty has dried, you can begin painting.

IMPORTANT: If there is no water-based or acrylic paint, you should coat the workpiece with PVA glue before applying any other paint. Moreover, it is necessary to apply several layers.

• It's time to apply water based varnish.

How to make a photo frame from disks: templates, diagrams with descriptions

For a similar craft needed:

• DVDs, CDs
• Black stained glass paint
• Thick texture cardboard
• Pencil, ruler, scissors, tweezers

You can get started:

• From cardboard cut out blank frame

• Now is the time to get busy cutting out pieces from disks.

IMPORTANT: These pieces must be irregularly shaped.

• Next you need coat the frame with glue, by gluing colored pieces onto it. It is most convenient to use tweezers. It is advisable to lay out the parts not tightly to each other, because you need to fill the gaps with paint.

• Now The spaces between the pieces are filled with paint. The edges of the frame can also be painted black.

How to make a photo frame for scrapbooking: templates, diagrams with descriptions

Necessary things to create a frame:

• Special paper for scrapbooking
• Cardboard
• Construction or stationery knife
• Scotch tape, glue, scissors, ruler
• Decorative elements, stencils for drawings

Operating procedure:

• On cardboard are noted product boundaries
• All excess is cut off– only the blank frame should remain.
• Received The blank should be glued to the back of the scrapbooking paper.

IMPORTANT: The excess edges of the paper must be slightly cut and then folded over the frame.

• All the edges future framework needs secure with tape. The upper part cannot be glued, since the photograph will be inserted through it.
• Further made of cardboard need to cut a piece for the back panel of the frame.
• Now it is desirable to create support leg for the frame.
• Remains the most interesting stage work – decor! It can be very diverse.

Attached several ideas:

Decorating, decorating and decorating photo frames with your own hands: ideas, decor, photos

Ready-made standard frames can also be beautifully decorated. Moreover, after decoration you will get unique and nice things:

Photo frame decorated with colorful spools of thread

DIY photo frame collage: ideas, photos Collage of photo frames in the form of a puzzle for children's photographs

As you can see, even novice craftsmen can create an original photo frame. Such a product will give the interior a unique charm and will definitely catch the attention of guests. And as a gift, such a photo frame will bring a lot of joy.

Master class on creating an unusual carousel photo frame