How to make a door in a overhead gate. How to make an up-and-over garage door with your own hands? Manufacturing stages, drawings and dimensions

The convenience of a garage for a car is not least determined by its entrance gates, which should ensure the safety of the car and close easily and securely. Nowadays, you can order or make several options for automatic designs yourself. Next we will look at how to make a garage door with your own hands.

Peculiarities

Unlike swinging structures, which in most cases have 2 leaves that swing outward, overhead gates have sections or rollers that rise upward. Their operating principle is different depending on the type - sectional, rotary or roller shutter. The design itself, including various elements: box, guides, rollers, lifting mechanism, much more complicated than simple swing gates.

But the installation costs and materials fully compensate for the reliability and convenience of regular use of such a garage.

Having a ready-made garage with a rectangular entrance opening, you can easily build overhead gates with your own hands. For installation you will need standard set construction tools, materials for sashes, guides and casings. It is enough to arm yourself with patience and include a little ingenuity so that in just a few days, without rushing, you can build a reliable and convenient design such garage doors.

Advantages and disadvantages

Before you decide to build garage doors with a lifting mechanism, you need to weigh all their pros and cons.

Experienced craftsmen note the following advantages of such systems:

• Saving free space. Unlike swing gates, which require external space for open leaves, overhead gates use space inside the ceiling.
• They are much more convenient to use, especially if they are equipped with a lifting mechanism, then you do not need to make any physical effort at all.
• Lift-and-swivel and sectional doors reliably protect the garage from burglary.

• For such structures you can use different types finishing and decor.
• Overhead gates can be used for single and double garages.
• The doors open and close silently.

It is worth paying attention to the disadvantages of overhead gates:

• The main disadvantage is the complexity of the design and installation. If you order the installation entirely to specialists, it will be expensive. If you do the installation yourself, then you need to carefully study the drawings, fasten all the elements carefully, level, because even a small error can lead to the entire mechanism being inoperative.

• A fully open gate takes up free space at the top of the opening and inside the garage under the ceiling.
• The mechanisms of such gates are designed for a certain load, so the doors and body cannot be overloaded, for example, when insulating.
• Overhead gates can only be installed in rectangular garage openings.

If the garage owner has taken into account all these features, then you can begin installation. But first you need to decide on the type of overhead garage door.

Kinds

The most common are 3 types of homemade lifting structures:

• lift-and-turn or panel:
• sectional;
• roller shutters

Up-and-over garage doors are the most secure against burglary due to the one-piece design of the door. When opened, it rises up, turning 90 degrees and taking a horizontal position. Their mechanism can be lever-hinged or counterbalanced. The first view on the levers represents the most simple designs, which ensure smooth and unimpeded movement of the sash to a horizontal position.

Counterweight gates are most suitable for heavy doors.

Lifting and turning structures consist of a frame (usually metal), guides along which the frame moves, a spring mechanism or a counterweight with a winch. Lifting can be done manually using a handle at the bottom of the housing. This is done easily thanks to the stretched springs of the built-in mechanism. You can improve this mechanism by connecting an electric drive, then raising and lowering the sash occurs simply by pressing a button.

The leaf of an overhead sectional door is assembled from several panels up to 50 cm wide, which are connected to each other by hinges. When it is raised, these panels (they are also called lamellas) move along guides on rollers. The movement is provided by a spring mechanism, drums and cables. This design is reminiscent of sandwich panels used in construction.

The mechanism of roller gates for garages is the same as that of roller shutters in shopping centers. Their folding slats are narrower than those of lifting-sectional types; when opened, they rise and twist into a special box of small width. Therefore, this type has a clear advantage - saving space inside the garage. There is no need to install long guides under the ceiling.

The materials for the frame, frame and guide rails of overhead gates are usually metal, but stainless steel is the best choice. The box can be made of thick wooden beams or metal corners. Solid doors of a similar design can be made in the form of a sheet of boards in a metal frame. They are often sheathed on the outside sheet metal.

To keep the garage warm in winter, you can sew it inside heat insulating materials: sheet foam or mineral wool.

The box is coated with an anti-corrosion primer, then painted in 2 layers of alkyd or waterproof enamel. It is best to cover the folding shield with galvanized steel or aluminum.

The slats on sectional or roller doors are usually also made of galvanized steel or aluminum; heat-insulating material can be placed inside the sheets. The surface of such panels can be of any color - to the taste of the owner. Moving structural elements - rollers, couplings, are made of plastic or light metals, guides are made of of stainless steel or other materials not subject to corrosion.

Automation of doors that can be opened using an electric drive will greatly simplify the use of the garage. Many drivers don’t want to bother with heavy doors, especially when it’s freezing or pouring rain outside. For any design and mechanism, it is possible to select an electric motor of appropriate power that will use current from the household electrical network.

There are several types of automatic overhead gates.

The most common schemes that are easy to do yourself are:

• mechanisms installed on the door leaf;
• fixed on guides;
• mounted on side posts.

It is possible to order finished design, the kit of which will already include an automatic drive for lifting, such, for example, are equipped with many roller shutters with galvanized steel slats.

In this case, after purchasing, you only need to correctly install them on the garage opening and connect the electric drive to the network.

Manufacturing

To make simple overhead garage doors, you can use ready-made sketches and calculations, only slightly adjusting their dimensions to suit your room. There are many example solutions for country house containing drawings and a detailed report including the necessary tools and materials.

Before you make the structure itself with a movable mechanism, you need to make sure that the opening, adjacent walls and ceiling are able to support its weight. To do this, you need to choose strong and dense floors without voids and reliable fastening systems. And the room itself must be protected from moisture penetration and other natural factors that can damage the operation of the gate.

Having chosen the appropriate type and approximate project for future sliding gates, we make a drawing with exact dimensions, based on them we calculate the amount of materials needed.

For a strong and durable lifting frame garage doors The most suitable metal profiles are 40x20 mm in size and at least 2 mm thick. Transverse and horizontal fastenings for construction can be made from 20x20 mm profiles. Gate guides are most often made from channels up to 20 cm wide, and the size of the rollers is selected depending on it.

The box of the lever-hinged mechanism can be made from a metal angle or beam. Parts of the required length are cut out according to the dimensions in the created drawing.

The rollers themselves, springs and the entire lever-joint mechanism are usually purchased ready-made. They are selected according to the dimensions of the guides. The remaining parts can be easily made yourself using welding machine and Bulgarian.

To manufacture the gate and install it in the garage opening, you will need the following tools:

• welding machine;
• grinder with cutting circles for metal;
• drill with drill bits required diameter;
• screwdriver;
• hammer;
• level;
• tape measure, pencil.

photos

For fastening, you must use suitable given weight structures with metal anchors or dowel-screws. If you plan to use it for fastening a metal corner anchor bolts, then you need to prepare a set of appropriate wrenches.

Installation

Before you install the lifting gate system yourself, you need to make sure that the opening on which they are installed has a perfectly flat surface: strictly vertical and horizontal levels, right angles. The supporting frame is the most important strength element of such gates, so you need to be as careful as possible in its manufacture.

If a metal corner is chosen for the box, then the width of its shelf should be 1.5 times the thickness of the sash. After all the parts are measured and cut, they are attached to the garage opening with anchor bolts and tightened securely. To make the box, you can also choose wooden beams with cross-sectional dimensions of 100x50 mm, which must be secured with 100 mm self-tapping screws.

The one-piece frame of the folding gate must be assembled on a flat, horizontal surface. After the metal profiles are cut to the required length, they are checked with a square and lightly tacked by welding. Next, check the right angles and dimensions again, including diagonally, attach the corner gussets and transverse stiffeners, then completely weld the structure.

After welding the frame, it must be cleaned with a grinder at the joints to remove burrs. Then it is coated with an anti-corrosion solution and painted. Boards with thermal insulation are sewn inside the metal profiles, and the outside is covered with sheet metal. Brackets with movable rollers are attached to the upper corners of the frame.

After this, guides for the future sash are attached to the ceiling. They should also be mounted as level as possible, double-checking the horizontal level, parallelism and perpendicularity to the doorway. Then the sash is temporarily installed in the opening in order to mark the location where the lever-spring mechanism is attached.

After the operation of the gate and the unhindered movement of the leaf along the guides have been checked, it is removed, the springs are installed, and they are adjusted. Lastly, a rubber seal is attached to the frame around the perimeter to seal the seams and softly close, install door lock and opening handle.

With careful and correct installation, as well as reliable protection from moisture, gates with a similar design can last for decades. And their repair can be limited only to lubrication of the moving parts of the mechanism, lever system, support rollers and replacement of the rubber seal. For prevention, lubrication can be carried out every season, and the outer rubber gasket can be lubricated with silicone before the onset of cold weather to protect against freezing.

For internal thermal insulation such gates can be used various materials, which are also used for wall insulation: mineral wool, polystyrene foam or expanded polystyrene. The last two are more effective, since they do not shrink over time, but they can be fire hazardous, so it is better to choose non-flammable types.

For many people, the garage has become a second home, and they really want everything in it to be beautiful and comfortable. Do-it-yourself overhead garage doors are a step in the direction of convenience and reliability.

In order for you to have peace of mind about your car left in the garage, you need to install reliable and durable gates.

When professionally manufactured, such designs have long won the sympathy of car enthusiasts with their beautiful design and relatively reliable protection. One thing I can't be happy about is the cost. Do-it-yourself garage doors are quite complex design, but people with little welding and plumbing skills are quite capable of doing them. And in terms of their parameters, they are not much inferior to factory designs.

Design principle

The main task of any overhead gate is to open the passage by lifting the leaf upward and holding it in this position. The simplest option, from which the design of such systems began, is a rotary (hinged) one: the sash is hinged and rotates freely, and in top position fixed with racks (supports). Naturally, few people will like this design, since it requires significant space to lift the entire sash and considerable effort, taking into account its weight.

Currently, do-it-yourself garage doors are mainly installed in one of two types: sectional and swing-up. Both options solve another problem: laying the gate leaf in its upper position without going beyond the dimensions of the garage.

Sectional overhead garage doors have a leaf made of several separate longitudinal strips up to 0.5 m wide, hinged to each other. The principle of operation is based on the fact that when the gate is lifted upward, each section moves along guides in two directions: first vertically up the rack, then horizontally along the guides on the ceiling. The sectional design of the door leaf allows for its bending at the top point. The main advantages of this design:

• safety in operation;
• small size.

Disadvantages: possibility of hacking, difficult to do with your own hands.

Tilt-up garage doors consist of a solid leaf that rotates and is simultaneously pulled upward along guide runners. When open, the sash is placed horizontally on the ceiling within the dimensions of the garage. Main advantages: increased strength and security against burglary, ease of control both manually and mechanized, the ability to do it yourself. Disadvantages include relative bulkiness and the likelihood of jamming if used incorrectly.

Design of overhead gates

As a homemade lifting gate, the swing-and-lift system is most widely used.

Overhead gates consist of the following main elements:

Figure 1. Design of overhead gates.

• door frame;
• horizontal ceiling rails;
• sash;
• swivel mechanism;
• compensation system.

The door frame is made of durable wood or metal beam in the form of two vertical posts and an upper lintel (horizontal beam) and is installed in the garage opening. Mounted on both vertical posts metallic profile, which is a guide for the vertical movement of the sash.

Horizontal ceiling rails have a guide metal profile for moving the sash in the horizontal direction. They hold the canvas on the garage ceiling when the door is opened.

The gate leaf is made in the form of a single piece (shield). The following materials can be used: a metal sheet, sandwich panel, profiled metal sheet, wooden shield, lined with metal. Inner side It is advisable to cover the canvas with a heat-insulating layer. In the upper part of the sash, rollers are fixed on both sides to move along the ceiling rails.

A rotating mechanism and compensation springs are installed on the vertical posts. Springs allow you to reduce the force required when lifting the gate by pulling the leaf in the direction of its horizontal movement.

Gate swing mechanism

One of the main elements of lifting gates is the lifting mechanism, which ensures their movement in the vertical direction. Two types of devices can be considered basic: lever-articulated and counterweight-based.

The lever-hinged mechanism is the most widespread and is distinguished by its simplicity and reliability. This mechanism is mounted on vertical rack in its middle part. It contains a lever whose arm is attached to the bottom of the gate leaf. When the gate is lifted, the lever, which is hinged at both ends, sets the direction of movement of the gate, while making a circular movement around the point of attachment of the mechanism on the post.

The lifting and turning mechanism on counterweights consists of a cable, one end of which is attached to the bottom of the gate leaf. The cable is passed through a block and has a counterweight at the other end. When lifting the gate, the cable provides vertical movement, which is guided by runners on the posts. The mass of the counterweight is selected sufficient to impart movement to the sash panel. This system is usually used with a heavy gate structure and requires increased strength of the vertical posts.

Manufacturing of overhead gates

Quite simple swing gates can be made in the following order. First of all, a U-shaped box is assembled from a wooden beam with a cross-section of 8x12 cm, which is attached to the garage using metal pins or anchors. Bottom part vertical bars fixed in concrete screed. The sash leaf is made according to the specified dimensions of the opening.

A U-shaped profile is used to manufacture the guide rail.

Reason for rotary mechanism formed from a steel angle 35x35 mm. On one side of the corner, 2 holes (8-10 mm in diameter) are drilled for installation on the box stand, and on the other side, 3 holes are drilled for attaching the spring compensator bracket. It is advisable to make this bracket from a 43x80 mm channel. A similar base is made to attach the lever on the other side, which is welded to the lower corner of the sash leaf.

Two wooden beams size 10x10 cm. The guide rail is made of two 40x40 mm corners by welding together to form a U-shaped profile. With the help of bolts, the rails are firmly fixed to the beams with the profiles directed towards each other. The distance between the rails must correspond to the width of the sash, taking into account the rollers. Plates with holes are welded to the ends of the rails to install stops that prevent the sash rollers from moving outward from the guide.

On upper corners of the gate leaf, an axle with a roller with a diameter of about 5 cm is welded at both ends. The rollers must be secured through bearings to facilitate movement when lifting the gate.

Necessary tool

When manufacturing and installing homemade overhead garage doors, you will need the following tools and equipment:

• welding machine;
• perforator;
• Bulgarian;
• electric drill;
• Grinder;
• hacksaw for metal;
• set of taps and dies;
• file;
• hammer;
• chisel;
• chisel;
• pliers.

Installation process for overhead gates

The installation of overhead gates begins with the installation of the swing arm. It is best to use a standard rotary-joint mechanism with mandatory adjustment of the length of the lever attachment.

It is advisable to find an adjustment based on the jack principle. If the lever is made homemade, then it is necessary to provide a mounting plate with grooves that allow you to change the length of the lever attachment up to 10 cm.

After installing the rotating mechanism and preliminary securing the lever, the compensation spring is fixed using brackets made of channels. Then the sash rises vertically and is inserted with its rollers into the profile of the rails on the garage ceiling.

Stoppers (of any available design) are installed to prevent the rollers from slipping out of engagement with the rails. The sash rises as high as possible and the final fixation of the turning mechanism levers and the final adjustment of the compensation spring are made. On the sash leaf with outside A conveniently designed handle is attached at the bottom.

Strengthening the structure of overhead gates is achieved by replacing the wooden beam with a metal profile.

You can install any gate in the garage, including the popular overhead gates. Despite the complexity of the design, there is nothing difficult in installation. With great desire and availability the necessary tool You can make overhead garage doors with your own hands without any problems.

Features of overhead garage doors

Gates that do not open like doors, but go under the ceiling, are assembled from several parts:

• a skeleton made of durable elements;
• one-piece sash inserted into the frame;
• return spring assembly;
• mechanism for changing the position of the sash.

This design is in great demand among garage owners because it has a lot of advantages.

Advantages

Lifting gates are characterized by the following positive qualities:

• compactness - the design takes up less space in and around the garage;
• ease of assembly and installation;
• automatic opening, which can be achieved by equipping the gate with a drive;
• free lifting of the sash, so there is no need to remove snow before entering the garage;
• noiselessness, which is guaranteed by a special mechanism for moving the door leaf.

Despite the advantages of overhead gates, some garage owners find compelling arguments against installing them.

Flaws

The following disadvantages of this design can force the garage owner to change his decision regarding equipping the garage with overhead doors:

• low degree of protection from intruders;
• inability to retain heat;
• prohibition on frequent raising and lowering of the sash;
• Possibility of installation only in a rectangular opening;
• necessity complete replacement canvas if it is damaged.

You can turn a blind eye to certain disadvantages of overhead gates. Some car owners ignore the fact that the door structure, which goes up, is mounted only in a rectangular opening. The fact is that this disadvantage is compensated wide possibilities in finishing the canvas. For example, small windows made of glass containing wire mesh in the thickness may be built into the leaf of an overhead garage door.

The principle of movement of the sash (rotary, tilting, folding mechanisms)

The gate, which goes to the ceiling, allowing the car to drive inside the garage, looks like a flat canvas that completely fills the opening. In order for it to rise easily, it must be supported by a rigid frame, securely attached to the wall of the room. The overhead gate leaf moves up or down along the side profile, which acts as a guide.

A special mechanism consisting of springs, levers and rollers forces the canvas to move from place. The sash, which is set in motion by these elements, rises along the guides and goes upward, after which it slowly takes a horizontal position and becomes parallel to the ceiling.

Easy and quick lifting of the canvas up is provided by springs. When the gate is locked, it stretches. And the opening of the door structure brings them into a compressed state. Springs and all other elements of the mechanism for moving a solid gate leaf can be forced to perform their task either manually or automatically.

Opening overhead gates at the touch of a button is achieved by electric drive, which need to be specially equipped with the door structure.

Preparing to install a standard garage door

The first task that a car owner who has the idea of ​​making a lifting gate needs to complete is to draw up a drawing. You won’t be able to do without it, since the final result of the work depends on it.

Drawing with indicated dimensions

A diagram indicating all dimensions is a document that can protect you from making skewed gates. By the way, when constructing a lifting door structure, it is advisable to have on hand not only a simple schematic representation of the gate, but also a plan with its isometric projection.

The dimensions of the lifting door structure should be 10 cm longer opening. By adding these centimeters to the door parameters, you will be able to avoid the appearance of gaps between the lifting structure and the walls of the garage. A large room may require the manufacture of gates with dimensions of 6x2.2 m. And the frame itself, created from steel or wooden elements, should be made taking into account the dimensions of the opening.

Having finished drawing up the drawing, you need to arm yourself with a pen and a notebook in order to note in it what will be needed in the process of manufacturing the overhead gates.

How to choose the right materials

To install overhead gates in your garage, you need to prepare:

• 2 wooden beams with a cross section of 100x100 mm and 120x80 mm, or strong steel profiles;
• corners 4 mm thick with parameters 4x4 cm;
• channel 40x80 mm;
• a steel rod with a diameter of 0.8 cm;
• 2 springs having an internal diameter of 3 cm;
• 2 movable brackets;
• anchor bolts and screws;
• rollers;
• cable or chain.

Most of the requirements are placed on the material from which the canvas itself will be made. To create a lifting (it can be folding or folding) sash, boards with a thickness of at least 2.5 cm, corrugated sheets and plastic panels are suitable. You can make a canvas from ordinary sandwich panels. Same good material board shields are considered.

The door leaf of a rising door structure cannot be made from solid wood. Otherwise, the sash will turn out to be heavy. In addition, in the rain and snow it will become damp and swell.

If, after making the door leaf, the garage owner intends to insulate them, then he can use basalt wool or polystyrene foam. These materials meet the requirements fire safety. Having insulated the door structure, you can sheathe it with galvanized steel sheet, which will protect metal parts anti-rust gate.

Required Tools

For measurements you will need a metal tape with divisions (tape measure), building level and a corner. In the future you will need:

• angle grinder for smoothing metal after welding;
• welding machine;
• an electric jigsaw, which is useful for cutting and processing wooden beams;
• a drill to make holes in materials;
• a screwdriver for equipping the blade with fasteners;
• hammer, set of screwdrivers and wrenches.

How to make a lift-and-fold gate structure with your own hands

To make a gate that goes to the ceiling when opened, you will need to perform the following steps in turn:

1. Prepare an opening for the structure, that is, insert it into the flooring to a depth of 2 cm vertical supports, which will be pieces of timber 120x80 mm, and attach them with anchor bolts.
2. Assemble the frame of the structure, for which it is necessary to install a horizontal beam at a distance equal to the length of the garage door in such a position that it is parallel to the crossbar of the opening.
3. Weld two guide rails from 4 metal corners, along which the rollers attached to the sash will later pass, and attach them using self-tapping screws and metal fittings to the beams located at the top.
4. Build the frame of the canvas. To do this, weld square profiles from metal corners, connect them to each other and attach them to the finished box of diagonal beams.
5. Equip the corners at the top of the frame for the canvas with rollers, for which you need to use a drill and fasteners.
6. Cover the gate frame with anti-corrosion material using self-tapping screws.
7. Equip the vertical support beams with movable brackets, installing channels of these mechanisms on them.
8. Attach to the bottom of the beams, or rather, to the suspended brackets and the ends of the channels using a spring.
9. Hang the finished canvas on the manufactured frame.

After this, you should take care of protecting the garage from intruders by equipping it with locks and latches. It’s worth thinking about how and with what to insulate your homemade overhead gates.

How to insulate garage doors

The garage can be protected from heat loss if the inside of the lifting doors is covered with foam plastic. This material is characterized by high rigidity, does not absorb moisture and does not allow it to escape outside. warm air. The quality of the foam, despite the low price, is beyond doubt. In addition, this material is easy to work with, because it weighs little.

It is first necessary to treat all holes between the frame and the canvas using polyurethane foam. This clever trick will protect the garage from heat loss through the door structure and the occurrence of drafts. Then you need to coat the gate leaf with a primer or paint that protects against rust. When the coating has dried, you can begin to insulate the door structure.

Polystyrene foam can be laid on metal surface gates or insert battens between the joists. If you like the first option, then the insulation will simply need to be glued to the sash. And when choosing the second method of laying polystyrene foam, the first thing you need to do is create a frame from wooden lining, and only then deal with insulation.

Later, in order for the gate to open and close without difficulty, it is recommended to adjust the spring tension by tightening the nut. If this does not help, you can change the location where this element is fixed. Lifting gates will tip over easily if they are equipped with a door handle from the outside at a distance of less than 1 m from the ground.

Video: how to make the simplest homemade overhead gates

The main condition for the successful completion of work on the construction of overhead gates is correct preliminary calculations. In addition, in order for the door structure delivered to the garage to cause pride and not regret, you need to take on its manufacture with construction skills.

When buying a car, every owner thinks about how and where to store it. Ideal place There has always been and remains a garage. Its convenience determines the quality of life, no worse than other rooms in the house. The installation of garage doors is becoming more and more convenient and practical every day due to the fact that the industry does not stand still. Classic swing gates fade into the background. Practical overhead garage doors are becoming increasingly popular today. Creating them yourself does not seem difficult if you have minimal skills in performing such construction work. To find out how to arrange them correctly, quickly and efficiently, read this article.

To make a homemade overhead garage door, first determine suitable option designs.

Based on this principle, the following types are distinguished:

Features of sectional structures

The most common type of garage door this moment- sectional garage doors. They are made in the form of panels 40-60 cm high.

Panels are made from several types of materials:

• plastic;
• metal;
• wood.
  Important! Determine the choice specific type material to create a garage door design, car dimensions, expected number of cars, as well as features design idea design of both the garage itself and the architectural ensemble on the site as a whole.

To maximize the quality of thermal insulation, such panels are filled with polyurethane, and the surface is protected with a special coating. The individual elements are fastened together with hinges. All moving parts, such as clutches and rollers, are made from reinforced plastic combined with steel components, and the guide skids are made from materials that do not corrode.

The operating mechanism of sectional garage doors is quite simple - they are pulled along runners to the ceiling when opened and fall vertically down when closed.

Advantages

The main advantages of such gates include the following features:

Flaws

In addition to the advantages, sectional doors of the lifting type also have a couple of disadvantages:

Distinctive characteristics of lift-and-turn solid mechanisms

When determining the features of such structures, it is certainly worth noting the following nuances:

Advantages

The solid-panel type garage door has a lot of advantages:

Flaws

Important! The main difference between these two designs is that sectional garage doors need to be installed only as a kit, whereas all elements of up and over doors can be prepared and installed with my own hands.

Video

Watch a video review of overhead gates to get a clearer picture of their operation and design.

Garage door installation tools

To install any type of garage door you will need the following tools:

Installation rules for overhead sectional garage doors

To correctly install sectional overhead garage doors, follow these steps in exact sequence:

Video

The video below will help you quickly complete the task of creating overhead garage doors. Please read it carefully.

Installation technology for overhead gates

Considering the fact that the construction of this type of gate will have to be done entirely on your own, we will highlight the main stages of the work in somewhat more detail.

What type of rotary mechanism should I choose?

Homemade garage doors are the most economical option filling the garage opening without restrictions in convenience, functionality and design solutions.

Before you start work, decide on the choice of mechanism by which the gate is directly opened:

How to make a project correctly?

To properly design a garage door, do the following:

What materials should I prepare?

Once you have drawn up or selected a sketch, purchase following materials and tools for work:

Installation procedure

Additional equipment

If you want to increase the attractiveness and reliability of the door leaf, equip it with the following additions:

Additional reinforcement

If necessary, strengthen the structure itself using one of the appropriate methods:

How to save money when installing garage doors?

The only thing you can do to save money when choosing overhead sectional garage doors is to install such a mechanism yourself. All other points, when trying to save money, will still require sacrificing certain advantages, although some options are quite acceptable. It all depends on your personal vision of the garage design and the regularity of its use.

Check out some of the most popular solutions to reduce the cost of garage door construction:

Conclusion

Overhead garage doors - modern way protect your garage from burglary with a convenient and beautiful shield. Whether you entrust installation and installation to specialists or do the work yourself is up to you to decide. The main requirement for further convenient operation is right choice suitable type garage arrangement, proper internal layout and compliance with all assembly instructions.