DIY floor lamp for reading books in a romantic setting. DIY floor lamp How to make a DIY floor lamp

The basis for a comfortable stay and work in a room is high-quality lighting. Thanks to different light sources that can be installed according to your imagination, you can divide the room into zones, highlight certain objects and decorative elements, decorate the facade of the house, your site, and much more.

Repair or do it yourself

In this article we will talk about floor lamps, and we will give a master class on how to make a floor lamp with your own hands. This way, you will create a decorative element that perfectly matches your design and will completely satisfy your tastes. Repairing a self-made device will also be easy to carry out. In addition, you can save money, because the price of a finished device can be very impressive.

We will tell you what materials you will need, describe all stages of assembly and show several options. possible design. We will give our recommendations and advice on the assembly process.

Necessary materials

Let's look at what we need to assemble the lampshade, base and other components of the device. By choosing fabric and threads that suit your interior, you can decorate the lampshade.

Here is a list of necessary materials and tools to make floor lamp with your own hands:

Wire cutters.
Construction spatula.
Baking pan, preferably detachable.
Parts for creating a lamp circuit: socket, incandescent or LED lamp and plug with wire. We recommend using LEDs, as they heat up less and are more economical.
Wire mesh, 400 mm wide
A metal tube or cornice will be used as a stand. The length depends on your preference.
Gypsum for construction.
Aluminum profile for frame and branches.
Black varnish, approximately 0.2l.
Silk threads - the choice of thread depends on your preferences.
Decorative braid.

Advice: Think about the dimensions of the future floor lamp in advance and calculate required amount materials. Thus, material costs will be minimal.

Master class on assembling a floor lamp

The first floor lamp we will show you will be a device with a wire shade. Thanks to lightweight materials, the design will be very light, transporting it from room to room will not be difficult, and repairs can be carried out without any difficulty. The use of threads in the design of the lampshade will help create high-quality lighting, because they will transmit light very well.

Lampshade frame diagram

The wire frame is not only very light, but also lends itself to literally any finishing method, using fabric, threads, etc. finishing materials. It can also be given a unique shape and make the design unique.

Let's start conducting a master class. The entire process of assembling a floor lamp will be divided into points:

Let's start with making the frame. We take our wire mesh and cut off the length that the lampshade will have around the entire circumference. Since we wrote earlier that the height of the mesh is 400 mm, this means that the base itself will be the same height. The long one must be made with a small margin so that it is possible to make a small overlap for fixation.

We make a round cone from the mesh, and carefully fix the junction of the two ends with wire.

Stages of manufacturing work

To create more solid foundation so that the wire does not bend during operation, add aluminum profile, securing the ego with tendrils from the mesh. For greater rigidity, you can also add a profile in the middle.

The base on which the entire structure will stand is made of plaster, in a prepared baking dish. Dilute the plaster with water and leave to dry. After some time, when the mixture begins to set, insert a tube in the middle. The hole on the tube should be closed.

We leave the plaster to dry at least overnight, and preferably for 18-20 hours.
A little trick to increase the strength of the base and prevent cracks from appearing is to add PVA to the mixture. Do not spare water, let the mixture be a little liquid, so that cracks will not appear during the drying process.

We weave the threads tightly into the frame of the lampshade. Try to wind them as close as possible to avoid creating holes in the walls.

We wrap the profile around the cartridge, to which we will attach the branches on which the lampshade will be installed.

After the plaster has dried, take it out of the mold and stretch the wire through the pipe, connect it to the cartridge and fix the cartridge itself on the top of the pipe.

We carefully paint the gypsum base with varnish. When the varnish has dried a little, but is still sticky, we wrap the base along the contour with decorative tape and cover it with varnish again.

Advice: To increase durability, it is better to varnish plaster and tape in 2 layers, this way it will gain greater strength and will not be so susceptible to damage.

That's it, our floor lamp is ready and can be used. This way you can make a very beautiful and unique lamp that will perfectly match your decor. In addition, it is easy to restore such a lamp or make repairs in case of breakdown. You can make several options for lampshades for it.

We make a lamp from what we have on hand

It’s hard to imagine, but a beautiful lamp can be made from items such as a plastic bottle, jar, or flower pot.

So, how to assemble such a floor lamp that we will need:

Container for creating a base.
Components for assembling a light source.
Any type of fabric, thread or paper for decoration.
Tube and aluminum profile to strengthen the frame and create branches.
Knife, ruler, scissors, pencil, pliers.

Select the required sizes of consumables yourself based on your wishes and needs.

Assembly steps:

We select the lid to the container that we use for the base. We make a hole in it in the middle, and with inside We make 3 stops that will prevent the tube from moving to the sides.
We make a hole in the container through which we pull the wire.
We pull the wire through the hole in the cover and secure the cover.
We put a tube on the wire and insert it into the cover and also fix it.
We fix the cartridge on the tube.
We will fix the lampshade and do it in the same way as described in the previous version of the floor lamp.

Tip: To prevent the possibility of a short circuit or electric shock, carefully insulate all contacts near the cartridge; it is best to use heat-shrinkable tubing.

Summarize

Making floor lamps with your own hands is very simple, and you get a very beautiful product several times cheaper than in the store. Restoring or repairing such a device will not be difficult for you, since you received a master class on how to create it and assembled it yourself without any help. You are free to choose the type of fabric, base color and general shape, which allows you to bring all your decorating fantasies to life.

People who do not know how to create things with their own hands always admire those who have the courage to do so, calling them creative individuals. And those who are engaged in home handmade do not fully understand the reasons for such admiration, because not everything is so complicated. Especially if we are not talking about creating all the elements of future furniture from scratch, but only about the layout, fit and original decor.

It is perhaps difficult to overestimate the influence of light in the interior. Lighting created at different levels and a well-thought-out scenario can significantly affect the atmosphere and overall mood of the living space. In particular, floor lamps miraculously create cozy islands in the living space, helping to properly zone it.

Making a floor lamp with your own hands is not just about sewing pillowcases on pillows or putting together photo frames. Still, the carpentry aspect is present here, and the electrics are involved, and the design aspect cannot be canceled. Let's find out in more detail how to make a floor lamp with your own hands.

Necessary materials for creating a floor lamp with your own hands

You can easily find the necessary materials in a hardware store, Alternative option- use partly an old floor lamp.

Must buy electrical cable, you can use an extension cord. - It is best to take a three-core wire, especially if the body of the future floor lamp is made of metal.
Will need cartridge E27 models (the most common version).
It is recommended to select lamp energy saving.
A stick of the required length, full pin. It is not advisable to choose a wooden one.
Something for grounds- stands.
Shade.

Making a floor lamp with your own hands

You found the time to create a floor lamp with your own hands, purchased everything necessary materials- it's time to start the installation process. You should start with styling electric cable into the future leg of the floor lamp. Before this step, you need to connect the wire to the electrical plug and socket. Check high-quality insulation all joints.

Making a lampshade with your own hands

It remains to create the most expressive part lighting fixture- lampshade. You can check with a consultant at the same hardware store for the availability of wire mesh. If you find one, you will need to roll it up so that you get the diameter of the desired size. You can also create a lampshade frame using regular wire. You need to make a cylinder out of it - in other words, connect several circles lengthwise.

When the “skeleton” of the future lampshade is already there, it’s time for your inner designer. How to successfully design a floor lamp? First of all, it should match your environment. If this is very difficult to do, try playing with contrasts. Build a decor that will clearly stand out from the general atmosphere and can claim to be an art object.

DIY fabric lampshade for a floor lamp

You can use almost any fabric for this project, from linen to durable denim. By the way, the latter can look very stylish in a bachelor or youth interior.

DIY knitted lampshade for a floor lamp

It is quite acceptable to knit a lampshade from large or small yarn and decorate it with decorative knitted elements. Such a lamp can be seasonal; it will look cozy and warm in the cold season.

Fantasy lampshades for floor lamps

There are absolutely no rules in creating a handmade lampshade. You can hang a wicker basket upside down and it will serve its intended purpose quite well. Do you have an unnecessary large globe? Why not use half of it for the same tasks? Very original, in the spirit of adventure. You can also make a lampshade from a dozen petals, hearts, butterflies - in a word, anything that can be laid out layer by layer to create an imitation of scales. It is impossible not to touch upon one of the oldest common methods - tying an inflatable ball with threads and securing them with PVA glue. Once the design dries and the ball bursts, you are left with a sturdy sphere that makes a great DIY lampshade for your new floor lamp.

Reading a newspaper or book on your favorite chair can sometimes be difficult due to lack of light. It is irrational to buy a lamp, but making a floor lamp with your own hands is much more economical - you can move it from place to place, adjusting the lighting as conveniently as possible for reading. In addition, such a product will perfectly complement the interior. Wood is used as the material for its manufacture - below is a master class in which ash is used to make the lamp.

When deciding how to make a floor lamp yourself and at home, it is not enough just to know the dimensions into which the parts will be cut. The instructions below provide all the information on this process - from marking to assembling the product.

We cut out the following elements of the future floor lamp:

sides (A) of the stand;
front part (C) of the rack;
back (B) of the rack;
bar E, which will be located on top;
sides of bracket D.

Parts A, B, C and E must be made with a length allowance of 25 mm, shown in more detail in the drawings below. The purpose of allowances will be described further in the text.

Note! If the blanks for the sides of the stand and the holder are fastened with double-sided adhesive tape, then it will be possible to quickly mark all the lines, intersection points, locations of future holes, and “in one fell swoop” cut out all the same or symmetrical parts.

On each pair of blanks we mark the top points and ends of the arcs. To make a flexible pattern, we cut out a 50x1830 strip from MDF 12 mm thick - it will help mark the arcs on two pairs of blanks. In this way, uniform and smooth arcs are drawn on long lengths and in the manufacture of various furniture, where necessary.

After that:

mark the cut corners at the end of each pair of blanks;
on the sides of A we mark the length of the back of B;
At the ends of the sides of bracket D we mark semicircular cutouts.
In all places indicated in the drawings we make holes with a diameter of 6 mm.

Focusing on the marked areas and making an angle, we file the ends of the holder D and the sides A of the stand. With help band saw We cut out the blanks along the marked contour, making an allowance on the outside. After that, we sand everything and separate the pairs of sides (we use white spirit to remove traces of tape).

We cut out tongues (grooves) on the back part B of the rack, and folds on the nearby part C.

Aligning the ends of the sides, we place the workpieces on the table so that their curved edges look up. We attach the back part B to them with a clamp, marking the angle of the lower bevel on it. We adjust the protractor to the same angle and miter saw saw off the bevel at the end of the back plank.

Wooden material is good for work because you can always use its trimmings. In our case, we need to cut out 3 inserts from them, each 25 mm wide. They will separate the sides A. To do this, we place them with the curved side up on the carpentry table, using clamps we fix the back part of the post B on them, after which, transferring the marks from them, we mark its final length. After removing the clamps, we file the back strip to the desired size.

We apply glue to the grooves of the rear part B of the rack, fasten it to the sides A, aligning the lower ends, after which we fix the entire gluing. Why all these manipulations are needed, you can see in the detailed drawing above.

Note! To make a floor lamp with your own hands even and beautiful, you need to insert bolts or studs into the holes for a while. This will align the sides. In order to install the rear part as best as possible, it must be pressed with clamps, and all work must be done starting from the bottom and moving up.

In the upper bar E of the holder we cut out dowels measuring 10 mm.

We set the saw blade at an angle of 13 degrees, after which we saw off the long part of the top bar to the length indicated in the overview detailed drawing above. Now we set the tilt of the disk to 16 degrees and saw off the short part of the top bar, using the same pattern as a guide. Aligning the ends of the sawn parts, glue them to the sides of holder D.

Making the base

The base of the product is also made of wood with your own hands. From the material (19 mm thick) we cut out:

top bar F;
upper rear part G.

When making blanks for the lower parts, we take into account the following nuances:

the bottom bar H is made 3 mm wider and 6 mm longer than the dimensions indicated in the figure;
the lower rear part of I is made 3 mm wider than the indicated dimensions.

Stepping back 25 mm from the edges of the upper rear part, we make oblique holes. We glue the part itself and secure it with self-tapping screws to the upper front blank.

To make a floor lamp with your own hands into a fully functioning piece of furniture, you need to think about how electricity will flow into it. Therefore, as shown in the figure below, at the bottom of the central part of the lower rear workpiece I we cut out a tongue (groove) of 10x10 mm - this will be the place for the electrical cable. After this, we make another 3x19 mm groove in the center of the cut hole.

Based on the drawing below, we drill oblique holes, making an indent of 25 mm from the edges. Now, we glue the result of our labor and secure it with self-tapping screws to the lower workpiece N.

Click to enlarge

We mark the shape of the top layer of the F/G base, cut it out and sand it. We place these blanks on the lower H/I, aligning them so that the end of the upper rear part G is shifted 10 mm relative to the end of the lower rear part I.

To mark the contours of the lower layer H/I, we outline the upper blanks F/G (photo above), making an allowance of 10 mm. In this case, instead of rounding the corners, we draw straight lines. We drill holes in the parts of the lower layer from below for subsequent screwing in four self-tapping screws. We process the drilling places with a countersink, after which we separate both layers of the base.

Based on the base diagram above, we make holes:

in the front upper F and lower H parts measuring 10 mm;
in the lower front part H - 38 mm.

After this, we cut out the bottom layer of H/I according to the markings.

We cut out the brace J, leaving the edge of the workpiece rectangular shape(no long bevel).

We fix it with clamps, after which we press the previously prepared part of the A/B rack against it (its lower part should be adjacent to the carpentry table for ease of connection). Now we transfer the markings of the rear part of the B pillar to the strut and cut out the required workpiece. After this, we sand it, and treat the sharp edges with sandpaper or a carpenter’s file with fine teeth.

We glue part J and secure it with self-tapping screws to the top layer of the F/G base. Then we glue and fasten with self-tapping screws the assembled blanks of the lower H/I layer.

We cut out the K bar (it will cover network cable), grind it and glue it into the groove, as shown in the photo.

Attach the stand to the base

We press the stand to the strut. We drill a hole into it through the rear part B of the rack and screw in a self-tapping screw.

On the upper front part of the base F we mark the location of the A/B pillar, after which we remove it. Drill holes F and K through the base. Then the holes from the bottom need to be countersunk.

We glue the A/B post to the J strut, then reinforce it with screws. In the sides of the rack, through the holes made in the base, we drill guide auxiliary holes. We secure the stand to the base with self-tapping screws. Using clamps, we press the front part of the post C against the sides A, which fit into the folds, marking the bevel angle at its lower end, after which we remove the clamps and file the bevel according to the markings. We reattach the workpiece in place, press its lower bevel to the base and transfer the markings from the sides to mark the final length. We file down the nearby plank and attach it to the sides of the post.

Installing the holder

Mark the shape of the hinge plate L and the place where the central hole will be located. We cut out the workpiece according to the mark and sand it along the contour.

Having turned the holder D/E over, we place it on the table for carpentry and between the side parts D we insert an intermediate piece, the cross-section of which is 6x6 mm. We place the hinge plate on it, aligning the hole markings made on it with the central hole of the sidewalls. Using clamps, attach the supporting trim to the side that is located further. Insert a drill into the hole on the side that is closer, then drill a hole through the entire plate. We take it out, sand it, secure it between the sides of the holder using 25 mm furniture ties (2 pcs.).

We insert the assembled D/E/L holder between the sides of post A and secure it with a 50 mm furniture tie. We install the end of the holder horizontally, and then fix it with a long piece.

We press 6 mm thick cuttings against the hinge plate L on both sides with clamps and drill one hole. Raise the end of the holder D/E/L by 130 mm and drill a second hole through the plates L. We drill the last hole after the structure has been raised another 130 mm.

Making the M head:

on a piece of 13 mm thick cutting we mark a circle (the diameter should be 25 mm);
drill a 6 mm hole in the middle of the circle;
We cut the workpiece around the circumference and sand it with 220 grit sandpaper.

From a 6 mm steel rod we cut a piece 76 mm long. We apply glue to it and insert it into the head M (the tip of the rod should protrude 6 mm). After the glue has dried, insert a locking rod into the holes in plate L and the sides of pillar A.

Adding a lampshade

The lampshade for the lamp being manufactured can be anything. You can buy it in a store or look among old things. The product will look more original if you show your imagination and make a lampshade for the floor lamp with your own hands. In addition, the frame for the floor lamp is quite simple to make.

To make the components of the holder - strip N and plate O - we cut a blank from a material 20 mm thick, the size of which is 6x305 mm. Stepping back from the two ends of the workpiece by 5 mm, we make a groove, as indicated in the drawing. We saw off one strip N from each end and fasten them using Double-sided tape. We drill holes d5.5, and make roundings on the parts while they are not yet separated.

In the remaining part of the workpiece, divide the width by half and drill a hole d10 in the middle, retreating 16 mm from one of the ends. We saw off a piece 32 mm long (a hole should be drilled on it). We glue the resulting fastening plate O to the strips N and fix it using clamps.

We remove all the fittings, carefully sand everything and apply a finishing coat.

How to make a lampshade with your own hands from a basket. Video instruction.

Assembling the product

We assemble all parts of the product except the N/O fastening. We pass the network cable through F-K base And A-C pillar, passing it around the hinge plate L and through the holder D/E. We leave an end approximately 90 cm long, on which we put:

bushing with internal thread;
nut;
N/O mount;
decorative sleeve;
part of the tube having an external thread.

We fix everything on the mounting plate O using a sleeve with internal thread.

In the lampshade, insert the tip of the wire into the mounting hole and add two nuts. By tightening one of them, we secure the lampshade, leaving the second one slightly movable. We thread a wire into the socket of the socket for two light bulbs, and fix the socket itself with a sleeve with an internal thread (the fixation is carried out on a tube with an external thread).

Click to enlarge

We tie the ends of the wires into a special knot and connect them to the cartridge wires. We pull back the excess part of the wire and close the structure with a lid.

We attach the N/O holder to the sides of holder D using 38 mm furniture ties. After this, we pull part of the wire through the stand of the product and install the power plug.

The product will not work unless a lamp is inserted into it. In our case, we will need two light bulbs. We screw them into the product and check its functionality by inserting the plug into the network.

List of materials and parts

Examples of floor lamps

Making a floor lamp with your own hands is not at all difficult if you apply a little imagination and creativity. This task will certainly take some time, special tools and materials, but the end result will definitely please its owner. A lamp made independently will have individual features and features, since no one else will have something like it. This creative process allows you to create floor lamps of any required size and the style that best suits the space. Often found on sale suitable option It’s hard, and it won’t be cheap, but in order to make a floor lamp with your own hands, you can use any available materials. Some difficulty may lie in installing wiring for lighting, but even the fairer sex can do this. So, let’s consider step by step all the processes of making a lamp at home, as well as Various types lampshade design.

DIY floor lamp: preparatory process

Before you start work, you need to draw up a sketch of the proposed lamp, decide on the desired height, shape of the lampshade and its design, and take appropriate measurements. Standard set Tools you may need include: drill, pliers, knife, scissors, screwdriver, special glue, pencil and tape measure.

We say “basic” because, depending on a particular model, additional accessories may be needed. The individual elements from which the floor lamp will be assembled with your own hands are: wooden or aluminum tube for the frame, fasteners, electrical system, including a cord with a plug, switch, socket and light bulb, wooden boards for decorating the stand, body (mesh, openwork plastic bucket, etc.), material for decorating the lampshade and decorative elements.

A beautiful stylish lampshade can be built using a wide variety of materials, for example, colored wire, fabric, paper, waste plastic bottles, wallpaper, etc. A do-it-yourself floor lamp (the photos in the article demonstrate this) can be done perfectly original design, if you use decorative clay in the manufacture of a lampshade, which is a fairly plastic material, dries quickly and lends itself perfectly to decoration.

For decoration, beads, beads, shells, rhinestones, appliqués made of fabric or paper are often used, while the decoration is carried out taking into account stylistic direction the room in which the floor lamp will be located. The simplest approach when creating a new lighting interior item is to reconstruct the old one.

How to update a lampshade for a floor lamp with your own hands

No matter how beautiful this or that piece of furniture is, and, in our case, a floor lamp, over time it may lose its aesthetic qualities, or may no longer correspond to a new renovation carried out using a different style. In this case, it is not necessary to resort to purchasing a new model - it will be quite enough to redesign the lampshade for the floor lamp with your own hands, and there are many types of implementation for this.

The simplest of them is to cover the lampshade with wallpaper. All you need for this is wallpaper and a special glue for it, which can be purchased at any hardware store. When choosing wallpaper, you should illuminate it with a light bulb in order to immediately understand what kind of light the floor lamp will produce when it is turned on. Having previously measured the circumference of the lampshade, we cut off a suitable piece of wallpaper. The lampshade must be removed from the floor lamp leg and wiped with a degreasing compound. After such preparation, wallpaper glue is applied to the lampshade, then the wallpaper is applied and fixed on the surface of the lampshade. You should not press them too hard, as unwanted bumps may form, which are difficult to eliminate, and the aesthetic appearance of the lampshade will be lost. When the structure dries thoroughly, it is returned to the leg. The updated do-it-yourself floor lamp is ready.

An excellent way to decorate a lampshade, as well as its partial restoration, is the use of decoupage technique. For such work, it is recommended to take napkins with a solid pattern, having shades that match the interior of the room (for example, for the kitchen you can prepare napkins with images of fruits, for the nursery - cartoon characters, etc.).

The lamp shade is initially primed with white matte paint. This is necessary to ensure better adhesion to the napkin. After drying (about 1 hour), we begin, in fact, the gluing process itself.

It is worth noting that in the case where the napkins are multi-layered, it is necessary to carefully separate only the layers with the pattern. Glue (PVA or wallpaper) is gradually applied to the prepared surface of the lampshade and napkins are glued. You need to act as carefully as possible, since it is quite difficult to correct an incorrectly fixed napkin without damaging it. When the lampshade is completely processed and the design is created, it is left to dry, and then treated again with glue and left to dry for a day.

At the final stage, you can cover the lampshade for the floor lamp, decorated with your own hands, acrylic varnish to give the finish strength and moisture resistance. Such a floor lamp can be decorated with beads by gluing them with a glue gun.

There are actually quite a lot of techniques for decorating a lampshade. Some craftsmen braid it with satin ribbons in a checkerboard pattern and decorate it with bows, use appliqués and embroideries. One of the extraordinary and original solutions how to update a floor lamp with your own hands, and, in particular, a boring white lampshade - cover it with used photographic film (the lampshade should have a cylindrical shape). Refracting through the frames, the light will cast bizarre patterns into the interior.

DIY floor lamp

Independent production of this floor lamp involves three main stages: constructing a leg with a base and electrical wiring, designing a frame with a lampshade and, in fact, assembling the entire structure together.

When starting to build a floor lamp with your own hands, the first thing you need is a stand. It can be made from gypsum, the amount of dry mixture of which is about 3 - 5 kg, depending on the size of the lampshade. You will need an aluminum pipe as a leg. Some savvy craftsmen use a fragment of an old tubular metal cornice as it.

For the frame you will have to purchase a mesh, the width of which will be equal to the height of the desired lampshade. The mesh is bent in a circle until required diameter, the excess part is cut off, and the edges are fixed by bending the wire. For structural strength, you can run aluminum tape along the entire circumference. Thus, the basis for the lampshade was obtained.

Now it's all about fantasy. Treat the frame of a floor lamp with your own hands from metal mesh possible in a variety of ways. For example, tie it with fluffy threads using the macrame technique, and tie flowers on top.

In the middle of the last century, things made using the macrame knitting method were very popular, and, as they say, everything new is well forgotten old. If the floor lamp is made for a room in a modern high-tech style, the best solution will braid its frame with black wire, leaving gaps, and then paint it with black spray paint.

DIY floor lamp made of fabric

You can also make a floor lamp with your own hands from fabric. In this case, the frame will be a structure made of thick wire. Any material can be used as a fabric, but preferably opaque (so that the frame is not visible), such as cotton, taffeta, dark silk, etc. The most matching colors turn blue, yellow, orange, green or red - they will give warm light. If you choose a fabric with a floral print and decorate the lampshade with elegant ruffles and bows, you can get a wonderful floor lamp for a room in a country or Provence style.

DIY wooden floor lamp

If the interior of the room is decorated in the Scandinavian or eco-style that is quite popular these days, you can make a floor lamp from wood with your own hands, or rather, from tree branches, which can be found in any park or forest. A massive, tripod-shaped branch will serve good reason for a floor lamp, and top part- a place for a lampshade attached to a rope. Or, on the contrary, the trunk can be mounted in a plaster stand, and several lampshades can be fixed on the diverging branches. The trunk can be decorated with multi-colored threads and lace. Please note that wood is a flammable material, therefore, for safety reasons, such floor lamps are equipped with LED or energy-saving light bulbs.

In conclusion, I would like to say that anyone can make a floor lamp with their own hands from scrap materials. Using the tips posted in this article, you can completely decorate your home with a new stylish lamp without investing any special financial costs. See photo below beautiful options decorating a floor lamp with your own hands.

DIY floor lamp: 30 photos of beautiful options for making a floor lamp updated: September 27, 2017 by: Kyiv Irina

Do you want to create a romantic atmosphere? Or cozy and warm? Or maybe fun and festive? This floor lamp will definitely help you.
Its advantages:
- Soft light that does not hurt the eyes.
- Low power consumption.
- You can turn the lamp on and off, control color and brightness from the remote control.
- Modern style, which will fit anywhere.
- In addition to control and brightness, there is a smooth color changing mode and a dynamic switching mode, fast and slow.

In general, not a lamp, but a find!
The heart of the lamp is a Chinese garland with a controller and remote control remote control. Plus the power supply that comes with the kit.
Quite inexpensive, bought it here -

If you have big problems with a budget, then you can take a simple white one LED strip and power it from the power supply.

Other materials:
The rest of the materials that I used to make the lamp are not in short supply and are available at any hardware store.
1. Wooden corners 4 pieces - anyone who has trimmed with clapboard will understand what we are talking about, if not, ask the seller.
2. Wood slats 4 pieces – there shouldn’t be any questions here.
3. Two types of fabric: 1) transparent with a pattern, for effect. The type of organza that curtains are made from. 2) Denser, for dispersion, fabric such as chintz. I’ll admit right away – I’m a complete zero in fabrics and sewing. I just went to a sewing store and chose what I wanted to look like... I don’t remember exactly what it was called.
Of course, you can limit yourself to one dense one, but I just decided to stand out.
4. Plastic corners 3 pieces - any construction material.
5. Small nails.

Making a lamp

We collect all the materials and move on. I ordered an LED strip from China and while it was on its way, I started making the frame of the lamp and cutting fabrics around the frame.

The first thing you need to do is decide on the size. I took it to a height of one and a half meters. Taking this into account, I’m sawing off 4 wooden corners. The main load-bearing parts of the lamp are ready.

Now we decide on the width - I took 30 cm. We begin to nail together with small nails. We do everything carefully so that nothing cracks. If it suddenly cracks, take PVA glue and glue it together.

One side is ready. We stuff corners onto it, sawn to the width minus the thickness of the sides.

Everything needs to be done proportionally. Everything must first be marked with a simple pencil. Don't forget about the legs of the lamp.
We assemble the frame - everything is ready. The biggest job is done. This is what ended up happening.

Now take the LED strip and glue it to the corners.

The height of the lamp is 1.5 meters. I took the tape 3 meters, that is, it goes along one corner and diagonally in another. If you want more brightness, take enough tape to cover all 4 corners.
LED strip adheres very well to wood.

Now we alternately wrap it in layers of fabric. First one, then the second. For fixation we use furniture stapler. We cut off all protruding parts. All this is done very simply and quickly.

Next we take plastic corners. Choose the color you like - there is a wide choice now. I thought a dark corner would harmonize well with the white color of the lamp and took it.

We cut the corners and glue the top and bottom first. Then we cut the corner lengthwise and glue the sides with strips.