Technoelast epp roofing roll technonikol. Technoelast EPP

Technoelastmost and Technoelast EPP 4.0 are made from a durable polyester base, onto which a polymer-bitumen binder, modified with SBS (styrene-butadiene-styrene) artificial rubber, is applied on both sides. The Technoelastmost material is covered with fine-grained sand on top and with an easily meltable anti-adhesive film with a pattern on the bottom. EPP 4.0 is covered with an easily meltable anti-adhesive film on both sides.

The modifier and base properties give the material properties such as:

- flexibility and elasticity: elongation of the material at break is more than 30%, elongation at break of the binder is more than 15 times, flexibility on a beam with a radius of 10 mm (“on the finger”) -25 ° C;

The heat resistance of the material is +100°C, which is 20-30°C higher than that of bitumen materials;

- excellent adhesion: to achieve cohesive (by material) separation there is no need to greatly overheat the material or base;

- light, quick installation, comfort at work.

The base must be dried, cleaned of dust and dirt, and leveled. The surface must either be cleaned of cement laitance by sandblasting).

Important: Technoelastmost “B” is glued to an unprepared surface, but the tearing occurs along the surface of the base.

Easily glued to the base. The lower surface of the material is covered with a film with a special indicator pattern: when the “snowflakes have melted” under the influence of the burner flame, the material is ready for installation.

The procedure for fusing material onto a horizontal base:

1. 5-6 rolls are unrolled on the prepared base, and the rolls are tried on one another so as to ensure an overlap: 6-10 cm along the longitudinal side, at least 15 cm at the ends of the rolls.

2. After this, the material is rolled back into rolls.

3. The material is fused “on itself” with a gas-air burner: one worker heats the material, standing with his back to the direction of gluing, the second one rolls out the material, being on the side opposite to the overlap.

4. Heating is carried out by smooth movements of the burner so that uniform heating of the surface of the material is ensured. A good practice is to move the torch in an "L" pattern, adding additional heat to the area of ​​the material that is overlapped.

5. To ensure 100% adhesion of the material to the base and the previous roll, it is necessary to achieve a small bead of polymer-bitumen binder at the point of contact of the material with the surface. A sign of good, proper heating of the material is the presence of a bead of polymer-bitumen flowing out from under the edge of the material. This roller also guarantees the tightness of the overlap. When insulating surfaces with a slope of more than 25%, it is necessary to roll the overlap with a roller to ensure its tightness.

6. On junctions (parapets, parts, etc.) of small height, you can use the “heat and stick” laying method: the material is heated, after which the burner is put aside and two or three workers glue the material onto the entire surface at once.

7. To fuse materials onto vertical surfaces, for ease of work, it is recommended to cut the rolls into panels 1.5-2 meters long. If the height of the insulated surface is significant, the roll material is applied in tiers, starting from the bottom.
To secure the waterproofing layers on each tier, it is recommended to install wooden antiseptic slats in height every 1.5-2 m, i.e. according to the height of the working grips.

8. Burning of the material is unacceptable. Its signs are:

Boiling and abundant flow of polymer-bitumen binder, its leakage;

Strong smoke, fire of polymer-bitumen;

Liquefaction of the upper surface of the material when it “sinks” under its own weight, leaving black spots of bitumen;

- “ripples” on the surface of the material, which do not smooth out after cooling: in this case, partial destruction of the polyester base occurs.

In case of burnout, the defective insulation must be replaced.

Shoe marks that may remain on the hot material (immediately after fusion, on a hot sunny day) are not dangerous, since they usually smooth out after cooling. However, you can only walk on uncooled insulation in soft shoes without heels or metal objects on the soles. It is also undesirable to bet on the material gas cylinders and other heavy objects. If necessary, weight-distributing stands with a support of at least 50x50 are used.

Technoelast from Technonikol is an affordable waterproofing and roofing material that is easy to install and resistant to the most severe operating conditions. domestic production. Today it is one of the most technologically advanced, not only in Russia, but also in the world as a whole, being widely used where others are unsuitable.

As for the prices, m2 of EPP technoelast, however, they remain average, which makes it in demand in the construction of a wide variety of buildings and structures, regardless of their purpose and technical characteristics. This is no less due to the simplicity of its design, which includes:

Base made of polyester, fiberglass or fiberglass;

Waterproofing layers made of bitumen-polymer composite;

Protective layers of polymer film and/or coarse slate coating.

Before you buy Technoelast, decide on its brand

from TechnoNIKOL also stands out for its variety of brands, which are divided into two categories:

Universal (intended for use in standard conditions);

Special (used in special conditions or having special properties).

Below we will look at the standard varieties of this material, of which four types are commercially produced:

Technoelast EPP - the base of the material is represented by a sheet of polyester, used as protective layers polymer film(for the top layer without a logo, for the bottom - with it), thickness 4.0 mm, weight 4.95 kg;

Technoelast XPP - the basis of the material is fiberglass, the protective layers are again sheets of polymer film (the top one without a logo, the bottom one with it), thickness 3.0 mm, weight 3.90 kg;

Technoelast is a material with a polyester base, its upper (front) protective layer formed by coarse-grained slate dressing, the bottom - by a polymer film, thickness 4.2 mm, weight 5.2 kg;

Technoelast TKP is a material based on fiberglass, coarse-grained slate coating is used to protect its upper side, and a polymer film with a logo is used on the lower side, thickness 4.2 mm, weight 5.2 kg.

Technoelast EPP is a leader among leaders

Among the above waterproofing materials from TechnoNIKOL Technoelast stands out for many reasons, but most of all, of course, for its price. Technoelast EPP, as mentioned above, is made on the basis of polyester, also sometimes called polyester, which today is cheaper than fiberglass, and even more so fiberglass.

The low price of Technoelast EPP, it should be noted, does not prevent it from having not only excellent tensile strength, but also quite good elongation, which is especially appreciated when installing roofing carpet in critical areas flat roofs. For comparison: the elongation of fiberglass and fiberglass is only 1.5%, while for polyester this figure reaches 30!

Photo by Technoelast:

For waterproofing needs, Technoelast is no less good. Waterproofing, by the way, can be done by him in relation to any building structures- and foundations, and walls, and floors, and roofs - as well as pipeline communications of overhead and underground laying. Including transmitting heated media, because the heat resistance of this material reaches 100 C.

Roofing carpet made of Technoelast TechnoNIKOL

Are you planning to buy Technoelast for installing a soft roof? Then you should know that the latter can be mounted from this waterproofing material only in two layers and no other. Its lower (lining) layer is made of material with the EPP index; for the upper (cover) layer, ECP is used. Attention: the layers are laid perpendicular to each other.

The price of Technoelast EKP is higher (this is due to the presence of a protective layer of coarse shale topping) than that of EPP, although not by much. As for the laying technology, in this regard they are the same, although with lining layers always more problems, because they are mounted directly on the base, which is rarely ideal.

Electronic store website: always affordable prices

Moreover, absolutely for any Technoelast - for HPP, for TKP, for EKP, for EPP, as well as for a number of special varieties of this waterproofing material. Regardless of what kind of Technoelast you need now, its price per m2 will probably not upset you and will not seem excessive or overpriced. Do you think this doesn’t happen nowadays?

In the electronic store GidroiSOL.ru this is the norm, which, importantly, applies not only to Technoelast alone. Prices of propane torches used for its fusing, and bitumen mastic, which is indispensable if you prefer not to fuse roll waterproofing, but to glue it, we calculate according to the same schemes!

Retail price: on request

Technoelast EPP is a roofing lining and waterproofing material.

Purpose of Technoelast EPP

Installation of roofing carpet for structures (lining layer); waterproofing of building structures. Particularly recommended for use in structures subject to movement. Application: industrial roofs, loaded roofs, foundations, underground garages, boilers, subway vaults, swimming pools. Combines with Technoelast EKP. Used at temperatures down to -35 0C.

Structure of Technoelast EPP

In production Technoelast EPP applying bitumen-polymer binder (SBS modified bitumen, fillers) to the polyester base. Protective on both sides polyethylene film(to protect the material from gluing during storage and transportation). Durable, strong and elastic material that reliably protects against moisture and is bioresistant. Installation is carried out by fusing using a propane torch.

As a lower quality analogue, you can use Technoelast EKP

Technical characteristics

Weight of material, kg./sq.m. 4.6

Thickness, mm. 4

Material length/width, m. 10x1

  • - in the transverse direction 400
  • - in the longitudinal direction 600

Moisture absorption within 24 hours, by weight, % 1

Mass of binder on the welded side, kg./m2 2

Modern market building materials offers many types of waterproofing manufactured by domestic and foreign manufacturers. Among them, the Russian corporation TechnoNIKOL, which produces roofing, hydro- and thermal insulation materials on bitumen and polymer based. One of the most popular types of products from this company is Technoelast - waterproofing, which became the basis for the development professional system protection of building structures, incl. buried in the ground, from the effects of both precipitation and groundwater.

The professional waterproofing system Technoelast, produced by the factories of the TechnoNIKOL corporation, includes a large number of materials that have different physical and mechanical properties, but in all cases create reliable and durable moisture-proof coatings for roofs, foundations, tunnels and other above-ground and buried building structures used in all climatic zones Russia.

One of the most common Premium class materials included in the system is Technoelast EPP waterproofing, designed to create a roofing carpet, protect foundations from the effects of groundwater and man-made water, as well as other building structures with increased requirements for the reliability of moisture protection. In the production of Technoelast EPP, non-woven polyester fiber is used (this is indicated by the letter E in the designation), onto which a bitumen-polymer binder is applied, containing a special thermoplastic and fillers. To prevent sticking when rolled into rolls, the material is protected by a polymer film applied on both sides - two letters P in the designation.

Technoelast EPP is produced in rolls 1.0 m wide and 10.0 m long, and the material thickness is 4.0 mm. Waterproofing retains its passport characteristics in the temperature range from -25 °C to +100 °C. Laying Technoelast EPP is done by melting its bottom layer using a propane torch and attaching it to the base, which makes it possible to obtain a protective layer, the entire surface of which is fixed to the base.

Laying built-up waterproofing is not a job for amateurs

Advantages of self-adhesive material Technoelast Barrier

One of the developments of the scientific and technical center of the TechnoNIKOL corporation is the self-adhesive bitumen-polymer roll waterproofing Technoelast Barrier, designed to protect building structures - foundations, walls, tunnels, etc. from the effects of precipitation, groundwater and technogenic waters in all climatic zones of Russia. Technoelast Barrier consists of non-rotting reinforced polyester fiber with a double-sided polymer-bitumen binder with high adhesive ability.

As a means of preventing sticking, the material is protected on top by a polymer film of increased thickness, and on the bottom by soft anti-adhesive fiberglass fabric. Included roofing pie Technoelast Barrier can be used as a vapor barrier, since high viscosity and adhesiveness enable the material to maintain its passport characteristics when punctured in the event of mechanical fastening roofing carpet and insulation.

Technoelast Barrier is delivered to the construction site in rolls 20.0 m long and 1.0 m wide. The material can be used at temperatures from -25 °C to +85 °C. The waterproofing is glued to the base, and maximum adhesion is observed at a temperature of the base and material not lower than +15 ° C. In other cases, the lower surface of the material is heated using an industrial hair dryer.

Before applying waterproofing, the base must be thoroughly cleaned

Why builders choose Technoelast

The high demand for materials of the Technoelast waterproofing system is explained by their good technical characteristics, in particular:

  • long service life of 25 - 30 years;
  • resistance to limited aggressive environments, which significantly expands the scope of application of the material;
  • bioresistant to bacteria, microorganisms, and rodents;
  • heat resistance, due to which the material does not slide off heated horizontal, vertical and inclined bases;
  • high flexibility and elasticity, due to which Technoelast waterproofing can be laid on pliable bases - corrugated steel sheets, board insulation, in addition, these properties allow the material to be laid on uneven bases;
  • possibility of laying welded materials at negative temperatures;
  • ease of installation of waterproofing;
  • compatibility with other bitumen-based materials, which allows it to be used for repairing old roofing felt roofs.

Waterproofing produced by TechnoNIKOL corporation enterprises is divided into 4 classes, starting with the Economy class and ending with the Premium class, which allows you to select the material depending on the requirements for protective coatings.

Despite the automation, you can’t do without supervision

The use of modern weld-on and self-adhesive waterproofing materials can significantly increase the service life between repairs protective coatings, increase labor productivity, reduce the impact human factor on the quality of work performed. The reliability and durability of waterproofing directly affect the amount of operating costs required to maintain the entire building, so the increased one-time costs required to purchase modern high-quality material will pay off fairly quickly.

Technoelast, like most built-up roofing materials, consists of:

  • base (fiberglass, fiberglass or polyester) - ensures durability roofing;
  • SBS-modified bitumen binder, increasing performance characteristics material;
  • polymer film with the logo of the manufacturer on the bottom side, protecting the canvas from mechanical damage, gluing of turns to each other, and also serving as an indicator of sufficient heating when fusing the material;
  • polymer film on the upper side (in the case of lower layers of material) or gray slate coating, designed to protect the bitumen binder from ultraviolet radiation and mechanical damage during operation.

Technoelast differs from other materials for soft roofs more sophisticated production technology and quality of materials used. Artificial rubber added to bitumen provides elasticity when low temperatures and heat resistance at elevated temperatures. The reinforced base is not subject to rotting and retains its strength characteristics throughout its service life.

The relatively high price of Technoelast waterproofing is compensated by improved technical parameters:

Characteristic

Unit change

Technoelast

Economy class waterproofing

Heat resistance

Flexibility temperature

Breaking force
no more

Lifetime

Technoelast is marked with three letters, which mean:

  • first - base type: E - polyester, X - fiberglass, T - fiberglass;
  • the second is the type of coating of the upper surface: P - polymer film, K - coarse-grained slate coating;
  • third - coating material with inside: P - polyethylene film.

Application

Technoelast is intended for waterproofing:

  • roofs;
  • interfloor ceilings;
  • foundations;
  • basement walls;
  • underground tanks;
  • swimming pools;
  • main pipelines;
  • others construction structures and designs.

To install the lower layers of the roofing pie, Technoelast is used, both sides of which are covered with film, for upper layers- material with a film on the bottom and shale chips on top.

Technoelast has the following advantages:

  • absolute waterproofness;
  • high tensile strength - Technoelast based on polyester and fiberglass is stronger than similar ones budget materials by 15%;
  • durability - the synthetic base is not subject to rotting, bitumen is not afraid of the effects of chemically active substances, mineral chips reliably protect Technoelast from ultraviolet radiation;
  • possibility of operation in any climatic zones - Technoelast can withstand temperatures up to +100 o C;
  • simple installation technology, the ability to perform work in winter;
  • affordable price - Technoelast is cheaper than most roofing materials.

It is beneficial to use Technoelast. Budget roll materials serve up to five times less than Technoelast, their price per m 2 is only 2 times less.

Technoelast from Ant-Snab company

If you decide to buy Technoelast in Moscow from the Ant-Snab company, the price will pleasantly surprise you. We work without intermediaries, we receive Technoelast directly from TechnoNIKOL factories. Discounts are provided for large quantities purchased. Payment can be made in cash or by bank transfer.

To buy Technoelast from Ant-Snab, you should:

  • choose a brand of roofing covering that meets the conditions of use;
  • calculate the need for materials using the online calculator available on the website;
  • fill out the order form;
  • agree on terms of payment and delivery;
  • If you have any questions, call our consultants.

Delivery by company transport is carried out within 1-3 days after placing an order within the Moscow region. By prior arrangement, it is possible to unload goods and lift them to the floor. To take out roofing materials independently, you should agree on the shipment date and method of payment. Come. Call. We are waiting for your orders.