Planting flowers in a tire at the dacha. Do-it-yourself flowerbeds from tires (37 photos): how to make them from tires, paint them, a flower slide from wheels, how to cut the product

To make flower beds you will need:

  • chalk or marker to mark the drawing;
  • a sharp knife with a thick blade;
  • electric jigsaw;
  • extension;
  • set of files;
  • any, including used, machine oil.

Preparing for work

Using worn-out tires, you can make an original flowerbed without much expense.

First of all, carefully examine lateral surface tires. Special attention pay attention to the fine print. You need to look for the word "steel" or make sure it isn't there.

The presence of this word indicates that the tire is reinforced with steel wire, so you will need a fine-tooth metal file.

If there is no inscription, the tire is reinforced with nylon, and to work with it you need to insert a large-tooth file into the jigsaw. soft wood. It is easier to saw rubber with a large-toothed saw, because you have to put in less effort.

Most often, steel wire is used to reinforce tires. trucks, but you still need to check the tire so as not to dull the file.

If you have not only a tire, but also a disk for it, you can make two types of flower beds - low and high.

The cutting technology is the same, the difference is in some nuances of marking and the method of “turning out” the tire. Moreover, it is necessary to determine what kind of flower bed you will make before you start applying the markings.

How to plant and care for club begonia is described in.

Marking

When applying markings, try to draw even, symmetrical lines and do not make the widest part of the flowerbed petals narrower than 7 centimeters. Less wide petals are much more difficult to cut because the rubber is not stiff enough to handle normal pressure with a jigsaw and file.

Regardless of whether you want to make a low flowerbed, low or high, the marking must be divided into three stages:

  • marking a small (inner) circle;
  • marking the large (outer circle);
  • marking the teeth (petals).

A small circle is marked 3–5 cm from the edge rim, if it is not there, then 5–7 cm from the side ring (place to install the disk). This is necessary to avoid damage to the file on the disc and to remove thin and overly flexible sections of the tire.

To draw an even circle, take a large piece of chalk and index finger, press your little finger against the rim (if you are marking a tire without a rim, then wrap your little finger around the bead ring of the wheel) and move a chalk or marker along the wheel. This will allow you to use the disk or ring as a guide so you can draw a neat and even inner circle.

We mark the tire like this

If the size of the petals is less than 7 cm, then the large circle is marked as described above. For taller petals, mark as above, but hold the top of the tire with your little finger, or use a tape measure to mark the perimeter of the outer circle. The distance between the marks is 5–15 cm. After making the marks, draw a circle along them.

Petals can be marked either by eye or using a tape measure. The shape of the petals is limited only by your imagination. These could be triangles, waves, sine waves, oblique teeth, squares, slits, or anything else you can think of.

Tire cutting

Before you start cutting, think again about what kind of flower bed you want to have. After you cut the tire, make changes to the design and appearance flower beds will not work.

Using a sharp knife, cut along the side of the wheel along any line. Then insert the required file into the jigsaw and lubricate it machine oil. Connect the jigsaw through the extension cord to an outlet, then insert the saw into the slot in the tire. Turn on the jigsaw and start cutting the wheel.

Follow safety rules when cutting tires

Please note that cutting a tire is a difficult and time-consuming task that requires compliance with safety rules:

  1. Try not to hold the tire with your hand on the cutting line close to the jigsaw. If the file breaks or pops out of the slot, you will injure your hand. While cutting, press the jigsaw forward firmly, but smoothly, without sudden jerks.
  2. If you have enough strength, then instead of a jigsaw you can cut tires with a sharp knife with a thick (at least 4 mm) blade. But this cutting method is not applicable for steel-reinforced tires.
  3. Start each cut only after you have lowered the knife into the tire to a depth of 2-3 cm and cut only by moving the knife down. This will help you avoid cuts and more serious injuries.

Turning the tire out

After cutting both sides of the wheel, you need to turn the tire out. This operation requires enough great strength and dexterity, so it may not work the first time.

If it doesn’t work, don’t despair, try again after a while or ask someone stronger to turn it inside out.

It is better to ask someone strong enough to turn the tire out

When turning the tire, do not be afraid of damaging it. Tire even from passenger car designed for loads that cannot be created by hand.

As a result, we should end up with something like this:

An inverted tire is an almost finished flowerbed.

Find out, .

We grow, plant and care for sedum.

Painting flower beds

If you have a spray gun, it is advisable to paint the inside out tire before installation. After all, with the help of a spray gun you will not only paint the new flowerbed, but also touch the adjacent soil.

If you only have brushes, then it makes no difference whether you paint before or after installation.

For painting, use nitro enamels or alkyd paints.

Wipe the surface of the turned-out tire with a dry, clean cloth to remove dust and remaining rubber shavings. Then degrease with white spirit, solvent “646” or acetone. When the liquid is dry, paint with a brush or spray gun.

If desired, the flower beds can not only be covered with paint of the same color, but also pictures or drawings can be painted.

The appearance of the flower bed can be anything, it all depends on your imagination and the design of the site

For ideas for decorating a flowerbed made of tires, see the photo in the gallery:

The easiest way is to set old tire onto the plot, throw soil there and plant seedlings. This is, of course, simple, but it doesn’t look like an exclusive decoration. Well, let's try to improve the situation. Take bright acrylic or oil paints, we will select several of them that are most compatible in color and paint several tires. Then we’ll install them on top of each other and get a wonderful multi-level flower bed.

An original do-it-yourself vertical flowerbed of tires is created from several tires of different diameters, stacked on top of each other like a pyramid. You can put a flower pot on top if you don’t have a small tire on the farm. After painting and filling the inside of the tires with soil, you can grow them in the resulting flowerbed. hanging plants, for example, petunia or strawberries.

Flower beds made from tires can also be hanging. Attach a strong metal chain (thick cord, rope, etc.) to the tire and hang it on a tree. In order to be able to pour soil into the flowerbed, the bottom of the tire must be covered. For example, fix inside a flowerpot with a diameter slightly larger than the inner circumference of the tire. Or put a thick piece of rubber inside - think for yourself, there will probably be a material suitable for covering on the farm.

A snow-white hanging flowerbed made from a car tire is a spectacular “highlight” of modern style

And if you get a little creative, you can make a composition out of tires on the theme of... well, for example, homemade tea party. Several tires will perfectly play the role of a teapot and a cup - just complement them with simple details - cutting a pipe and bent pieces of metal tape.

Turtle flowerbed - fun creative

From a tire and tread, cut into equal 4 parts, you can make a flower bed in the shape of a turtle. We make cuts in the sides of the tire and insert tread scraps there - these will be the turtle's paws. We secure them with wire staples. We cut out the tail from a piece of rubber and also secure it with staples. For the neck of the turtle, take a piece plastic pipe, on which we secure a head made of crumpled newspapers with tape. You can put a straw or plastic panama hat on your head.

This do-it-yourself bed of tires must be painted according to all the “turtle” rules, otherwise it will not be clear what you wanted to depict. Draw eyes, a mouth on the head, paint the torso and paws in a bright color.

Flowerbed made from an inverted tire

Flowerbeds made from inverted tires resemble pot-bellied round flowerpots, to create which you will need:

1. Cut out a design of flowerbed petals on the top of the tire

Petals can be rectangular, triangular, round and even wavy. To begin with, they should be drawn with chalk or soap, and then cut out using a sharp knife, hacksaw or jigsaw. If you decide to use a knife, we recommend that you moisten it with soapy water while working - this will make it easier to overcome the resistance of the dense rubber.

Carefully cut out the petals using any sharp cutting tool

2. Turn the tire inside out

Many people are interested in how to turn a flowerbed tire inside out, because this is not an easy task and requires considerable effort. To do this, you need to turn the tire upside down with the side on which we did not cut anything, grab the cuts from the bottom with your hands and, pressing on the tread, carefully turn it out. Once you've done about half of the tire, flatten it into an oval and easily turn the rest out.

3. Paint the flowerbed in a spectacular color

We paint the resulting flowerbed in any color that will be in harmony with the rest of the landscape objects on your site. You can settle on a single color, but multi-colored ones, for example, in the form of stripes or a bright pattern, will look more impressive.

Vases on a leg - a more complicated option

Let's look at how to make a flower bed out of a wheel. This means that to create a flower bed we will use a tire with a metal disk in the middle. To do this, place the wheel on a flat surface and cut out the pattern of the petals, reaching with a knife (or other cutting tool) to the tread.

Then we turn out both the upper and lower parts of the tire without removing the disk. As a result, you will get a kind of flowerpot in the form of a flower on a leg, into which soil is poured and plants are planted.

After this, you need to take care of how to paint the flowerbed from the wheel. The upper part can be painted in a bright “floral” shade, and the lower part in green. Then a huge rubber flower with living plants in the middle will bloom on your site.

Master level - flowerbed in the shape of a swan?

A swan flowerbed is made similarly to a flowerpot made from a tire, the only difference is in a more complex cut out design. If for a flowerpot it was necessary to form the same type of petals, then here - the wings, tail, neck and head of a swan. We transfer the diagram to the surface of the tire and begin to cut out the figure of a swan. The head and neck are cut out along the black contours, the tail along the red ones, and the wings along the blue ones. After this, the tire is turned out in the same way as in the two previous cases.

We make a beak from a piece of rubber (wood, plastic or other material) and paint it with red paint. We put the two halves of the head together, insert the beak between them and secure all parts of the head together with self-tapping screws. We screw in self-tapping screws on both sides of the head in the places where our swan's future eyes will be. Then, so that the screws are not visible, they are covered with two circles cut out of black electrical tape - these will be the eyes. Raise your head straight and up, slightly pressing it into the tire. This creates a fold, which also needs to be fixed with self-tapping screws.

On last stage At work, the swan is painted - here you can show your imagination and come up with any color for the bird’s plumage.

The problem of recycling used tires has been of concern to environmentalists since the late 70s of the last century. This is especially true for our country, where there is no sufficient quantity enterprises capable of using them as recyclable materials. As they say, in such a situation, everyone saves themselves as best they can, so we can only welcome those craftsmen who are trying to free landfills from this non-degradable waste and, for example, make flowerbeds from tires with their own hands. They can be very different, from simply worn tires dug into the ground in which flowers are planted, to complex flowerpots in the shape of swans with a bright pattern. If you are interested in this idea and want the area in front of your house to be decorated with a beautiful tire, you can read below how to make one with your own hands.

Which ones to use

If you have the opportunity to choose, then a complex flower bed made of tires, made with your own hands, the production of which involves cutting out figures, will look better if you use foreign-made products, since they have thinner and more pliable rubber. In addition, it makes sense to give preference to winter tires, since they are more textured, and worn-out tires. The fact is that a worn proctor is softer, so the process of turning it inside out is easier and does not require much effort.

"Flower"

To make original ones with your own hands, just take 4 any tires, preferably the same size. You will need to remove the rubber from the metal rim and cut it so that you get two identical halves. You need to do this with three tires, and leave the rubber casing of one untouched, since it will be used as the core of the flower. Then the halves and the whole tire must be painted in various colors and dig 5-6 cm into the ground, laying out a flower with 6 petals with a round center. The composition will look more interesting if the core is planted with flowers of one type, and the petals with another.

Flowerbed-pyramid

This one is very simple and nice option Do-it-yourself flower beds made from tires are suitable for plots or yards with a small area. To implement it, you will need 6 tires, which need to be painted in bright colors and laid in 3 rows, in which there will be 3, 2 and 1 tire. If the dacha plot is quite spacious, then you can make the design more complicated by placing a flower of 5-6 tires in the bottom row, 3 in the second row and crowning it with one. Such a pyramid will look especially impressive if you choose a plant with large leaves for the top “pot”.

DIY flower beds made from car tires in the form of a vase

There is also a more complex option, the implementation of which will require a lot of patience. However, the result is usually simply excellent.

So to create original flower beds from tires with your own hands in the form of large vases reminiscent of open flowers, you need:

  • Place the tire on a flat surface and use chalk to draw petals of the desired shape around the entire circumference. In this case, the size of each petal should not exceed 12 cm.
  • Cut the workpiece with a sharp knife or jigsaw along the marked contour. To make this task easier, you can apply a little liquid soap to the knife from time to time.
  • Make longitudinal cuts along the tread grooves at a distance of about 10 cm.
  • Using a grinder, make several cuts along outside and smoothly cut the rubber with an indentation of 15 cm. If everything is done correctly and the grinder touches the metal cord, white smoke should be released.
  • Turn the tire inside out so that you get a kind of flower on a stem.
  • Decorate using enamel, oil or nitro paints.

To make a flower bed made of tires with your own hands even more beautiful, you can apply an ornament or stick various decorative elements on top of the base layer of paint using a stencil.

Pyramid slide

If you have 3 tires of different sizes, or at least two and one plastic bucket with a capacity of 0.5 liters, then you can make a pyramid according to the principle of a well-known children's toy. To create it, tires need to be laid on top of each other in descending order of diameter, filling each one with earth. You need to place a bucket on top and plant climbing plants in it and in the tires from the lower layers, so that as they grow, they hang down from the hill, covering it all.

Flowerbed "cup"

A flower bed made of tires, made with your own hands in the shape of a cup, will also look original. Moreover, if space allows, then you can even install a whole tea set on your site.

For such a craft, first of all you need to make a lower part that will represent a saucer. You will need a tire from a truck, with which you need to cut the sidewall with a jigsaw (to make the work easier, it is recommended to cool the jigsaw blade from time to time soapy solution). Having finished this work, take an R13 tire and cut off the sidewall with a well-sharpened, or even better, shoe knife, lubricating the blade liquid soap. After this, the tire is turned inside out so that the tread is inside, and you get a bowl without a bottom. Next stage— making the upper part of the mug, for which you will need a tire of a slightly larger diameter, for example, from a UAZ. Both sides are cut off. In this case, on the one hand, this should be done so that the resulting hole is not the same size. larger diameter"bowls". In addition, a strip for the handle is cut from scraps of the largest tire.

When all the details are ready, you should start painting and assembling the flower bed. To do this, the “saucer” and handle are painted one color, and the parts of the mug are painted another. Next, at the place where they are going to install the flowerbed, lay a piece of cellophane and place a “saucer” on top, and first install a “bowl” in its hole, and then the upper part of the mug. Next, use self-tapping screws to secure the handle and use a stencil to apply the mug to the mug in the color of the “saucer.” All! Now you know how to make a flower bed from a tire in the shape of a cup with your own hands. All that remains is to fill it with soil and plant flowers.

"Piglet" and "Ladybug"

If you are wondering how to make it with your own hands in a simpler way, but so that it looks original, you can use your imagination. To do this, you can simply remove the “elastic” from the rim, turn it inside out and paint it accordingly. For example, if you want a ladybug, you can paint the tire red, apply black dots using a stencil and depict a muzzle with eyes. You can also make a funny pig by painting an inverted tire bright pink and attaching a spiral tail cut from a plastic bottle. After the soil is filled into such a flowerbed and the plants are planted, you need to cut out a head with ears and a snout from a piece of rubber from another tire and insert it inside the tire circle, between the flowers.

Flowerbed "frog"

A flower bed made from tires, made with your own hands, can be the most different shapes, for example, resemble a frog. For this craft you will need:

  • three used car tires;
  • two lids from one-kilogram buckets of ice cream or ghee;
  • PF enamel green, yellow or red;
  • self-adhesive colored paper;
  • hose;
  • awl;
  • sponge;
  • wire.

How to make a flowerbed "frog"

The manufacturing process is very simple: the tires need to be painted in green color and, if desired, apply yellow rims on top. Then install two tires in the chosen place, and a third one on top, between them. From a hose, also painted green, you need to cut two sections about 1 m long, and from another tire - 4 legs and lay two in front of the lower tires, and two between them, having previously attached “hoses” to them. When the frog's body is ready, you need to move on to designing its head. To do this, you need to paint eyes on the lids of the ice cream buckets, and a mouth with red paint on the top tire. After that, all that remains is to fill the soil and plant the flowers. If you wish, you can turn the frog into an enchanted princess by making her a crown from a plastic bottle painted with yellow paint.

"Sun"

Many summer residents are interested in making their own hands in the form of the sun. For this craft you will need one tire, bright yellow paint and several plastic bottles. The tire must be removed from the metal wheel and buried in the ground so that only a semicircle remains above the surface.

Then you need to make holes on the tire with a diameter equal to the size of the necks of plastic bottles, and, after lubricating them with glue, screw them into the tires. After this, the entire structure needs to be painted yellow and plant flowers.

Flowerbed-pool for aquatic plants

Water lilies can be an excellent decoration summer cottage. However, what to do if it is not possible to equip at least a small pond or swimming pool? In such cases, it is enough to make a “water” flower bed from a tire. To do this, you need to cut off the top part of the tire and dig it halfway into the ground. Then you need to lay on top a round piece of a special waterproofing film, which is intended for arranging swimming pools, with a diameter 1 m larger than the diameter of the tire. The edges of the film protruding above the side of the tire must be folded outwards, secured and covered with small round stones or broken brick. All that remains is to place at the bottom of the reservoir a small mesh basket with soil in which the roots of the water lily are planted.

Modern landscape design characterized by original and bold decisions. These include original flower beds made with your own hands from tires, which look very attractive and do not take up much space. The desire to decorate your site, create interesting flower arrangements, quite naturally, and the unique installation is also a source of pride for the creator.

Flower beds made from tires - simple and tasteful

You don't have to be a professional to create flower beds from tires. upper class. First, they decide on the location of the future composition and make a sketch of the structure. On small area It is appropriate to arrange a single form in the form of a cute frog, a graceful swan, a fairy-tale carriage or a bright parrot, as in the photographs of flower beds below.

A spacious lawn requires larger installations. For example, multi-tiered flower beds made of car tires or vertical volumetric structures as in the following photos.

Flowerbeds can come in a variety of shapes:

  • Low and high.
  • Round and oval.
  • Multi-tiered.
  • In the form of animal figures, objects and flowers.

After the location and shape have been decided, materials and tools are prepared. For work, in addition to tires, a sharp knife and paint, the following may be useful:

  • Stones different sizes.
  • Metal grid.
  • Technical marble.
  • Remains of building materials.
  • Decorative stone for aquarium, etc.

When everything is ready, you can start working.

Making flower beds from tires

The simplest is the flower shape. The higher the tire, the larger it will be. Before you make a flower bed out of a tire, you need to choose a tire. It is better to take a used imported product with softer and thinner “winter” tires. It's easier to work with her. The tire is first cleaned, washed and dried. Then the lines of the future petals are drawn in a contrasting color, the upper part is cut out and removed, as in the photo of the flower beds below.

For further decoration, enamel, oil or nitro paint is used. On a clean and dry rubber surface they are distributed evenly and last a long time. You can also use tires to paint flower beds. car paint or aerosol can. It's better to choose the color light shades so that the roots of future plants do not overheat. The design of pure white tires looks very elegant.

Or a multi-tiered flowerbed of tires decorated with light stones of different sizes.

The combination of different colors looks interesting.

Or, conversely, a monochromatic composition.

When painting tires, you need to slightly capture the upper part of the surface from the inside to give a more aesthetic appearance.

Before painting, you need to carefully consider how the tires with blossoming plants will look. If the flowers are supposed to be bright and contrasting, then the tire should be monochromatic and modest. And, conversely, with an intricately shaped flower bed, the flowers are planted small and low.

A flowerpot will look interesting when the color of the plants echoes the shades of the container. If desired, you can glue glass aquarium pebbles to the flowerbed in the shape of a flower. oval shape– they will create the illusion of dew.

Multi-tiered flower bed

This installation will require several tires of different or the same diameter. The middle is cut out of them to make rings and the structure is assembled:

  • Install the largest tire first.
  • The bottom is lined with sand and crushed stone. Fertile soil is poured on top.
  • A smaller tire with the same filling is centered on top.
  • The number of tiers depends on the size of the elements.
  • Flowers or useful plants(strawberries) are planted in the gaps formed between the rings.

Flowerbed - tire swan

An ordinary tire, painted in White color, can become a real masterpiece. For a swan figurine from it inner part is not cut out so that its weight can hold its shape.

30-40 mm are retreated from the edge of the tread and two rounded cuts are made parallel to the circle on opposite sides on two-thirds of the entire surface. The narrow middle part will make the neck, and the wide side parts will make the wings. The middle part is cut off on one side and a head is formed at its end. Then the tire is turned out and the wings appear. They are finished with cuts of varying lengths that imitate feathers. The wings can be bent in any way - the angle of inclination can be any. All that remains is to paint the bird white, let it dry and you can plant flowers, for example, forget-me-nots.

Video on how to properly cut a tire for a flower bed



Every owner country house seeks to decorate the territory of the adjacent area. Buying industrial flowerpots made of concrete or plastic modules quickly solves this problem, but is accompanied by serious costs. To save money, you can use step by step guide to create such simple product like a flower bed made from tires with your own hands: photo of a flower bed made from wheel tires And practical recommendations will help you navigate this issue.


The feasibility of making a flowerbed from tires with your own hands

Creating a flower bed on a site is one of the most effective ways improve the landscape. The original and bright design of the product will become the object of everyone's attention. Flower beds are often made from scrap materials, such as car tires. This point is due to the fact that the rubber from which the wheels are made can easily be various types processing. It has a flexible and elastic structure that allows you to give products the required shape.


By using tires to make flower beds, you are also taking care of the environment. Most motorists throw their used tires into a landfill, where they occupy usable area and pollute environment. If you don't have the material on hand, you can ask your neighbors who don't need old tires for it.


Car tires can be painted. To improve decorative characteristics, many owners summer cottages complement their appearance with other materials, while creating flower beds with a unique appearance.


Advantages and disadvantages of tire products

Numerous photos of a flowerbed made from a tire with your own hands, which you can come across on the Internet, indicate that the main advantage of a rubber product is its originality.

There are other advantages:

  • simple and clear technology manufacturing;
  • the ability to achieve interesting shapes due to the characteristics of the material;

  • the ability to color finished products;
  • external attractiveness;
  • low costs (subject to the availability of used tires).

There are practically no disadvantages to this method of creating flower beds. The only downside is that not all owners of summer cottages consider this material option as a car tire attractive. Some of them are inclined towards more elegant or simple flower beds that do not require time and effort to create.


Types and photos of flowerbeds made from tires with your own hands

To create an original flower garden from wheel tires you do not need to have any special skills or knowledge. You just need to familiarize yourself with the basic information, have instructions and the appropriate tools at hand.

According to the type of construction they distinguish the following types flower beds:

  • low;
  • round;
  • tall;
  • single-tier;

  • curly;
  • multi-tiered;
  • hanging.

A round flowerbed in its original form is the simplest and most laconic design option. All you have to do is paint the tire the color you like, fill it with soil and plant the plants.


Multi-level structures are created based on tires with different diameters. They are placed on top of each other (in descending order of size) and filled with soil. Conventional tires of the same size can also be stacked using the pyramid principle. Only in this case a certain number of wheels are placed at the base of the structure and with each tier this number decreases.

Flowerbeds hanging type attached to a pipe or tree branch with chains or a rope, having previously covered the bottom with some material. This type of flower garden is created according to the principle of a flowerpot.


To begin work, you should decide on the design and its dimensions based on the available materials and the size of the site where the flowerbed will be installed. It must be taken into account that large areas It is recommended to install large and massive products. Multi-tiered flower beds or compositions of large quantity small flower beds.

Take advantage useful tips, to create with your own hands a flower bed from tires, the photo of which you liked.


Rules for creating a successful flower bed:

  • rubber intended for use in conditions winter roads, is more flexible and much more convenient to use than the summer one. It does not require much effort when cutting;
  • When choosing tires, it is better to choose those that are worn out as much as possible. The rubber on such wheels has become thinner and softer, which makes handling easier;

  • tires with worn tread are much easier to turn out;
  • At the initial stage of creating a flower bed, the material is always prepared for work. To do this, the tire is thoroughly cleaned of traces of dirt and foreign objects;
  • if you plan to cut out shaped elements, you need to apply preliminary markings to make cutting the material easier and make the result accurate and neat. For these purposes, it is best to use markers and chalk.

How to paint a flowerbed made of tires: photo, instructions

It is not recommended to leave the flowerbed in its original form after work on its shape is completed. A black product looks unsightly. Before starting work, you should stock up on paint and materials for decorative decoration flower garden Think about your future design in advance. Bright colors will diversify the appearance of the flower bed. They can be combined.


Allowed use:

  • patterns;
  • drawings;
  • geometric images.

Rubber is a specific material that requires special handling. For coloring a product from car tire The following types of paints can be used:

  • automobile;
  • oil;
  • nitro paint;
  • enamel.

To increase the adhesive properties of the oil-based paint composition, it is recommended to pre-treat the rubber surface with a primer. This preparatory procedure will allow you to get rid of roughness and unevenness that may be on the tire. The optimal primer in this case will be GF-021. It will reduce paint consumption. To enhance the strength of the coating, a small amount can be added to the primer adhesive composition PVA.


The flowerbed must be painted not only from the outside, but also from inside. Since the black edges will still show through the green spaces. The primer is applied to the surface of the product using a brush. The painting process can only begin after it is completely dry.


Do-it-yourself flowerbed from tires: photo of a flowerbed from wheel tires and creation technology

At first glance, it may seem that the worn rubber of a car tire is not the best best material to create a flower bed. The rounded shape of the tire itself looks quite simple and boring. But this does not mean that the design of the flower bed is from of this material strictly limited to its original form.

Flexible rubber allows your imagination to run wild and come up with many design options that are suitable for creating a flower garden on your site. Most of Such products do not even evoke the idea that the material for their production was old car tires.


Conventionally, the most popular design options can be divided into several categories:

  • objects (pot, tea set items, for example, cup, teapot);
  • birds (flamingos, swans, cockerels, parrots, penguins);
  • flowers;
  • animals (turtles, frogs, pigs);
  • figured objects (pots and flower beds with original slots and curved shapes).

Each type of design has its own manufacturing characteristics. Using guidelines for creating beautiful flower beds from car tires, you can easily fill your site with original products.

Features of creating flower beds from wheel tires with your own hands: photos and tips for making flower beds in the form of objects

Flowerbeds in the form of voluminous flowerpots can most often be seen in suburban areas. Such designs are simple to implement and have an impressive appearance. To begin with, you should take care of the availability necessary tools, materials and related devices:


  • tires;
  • coloring composition;
  • primers;
  • chalk (soap, marker) for marking;
  • metal mesh;
  • tassels.

The simplest flowerbed in the shape of a turtle will require two identical tires, an old rubber ball and springs. One tire is laid on the ground and remains intact (it will be the body), the second is cut so that in the end there are four pieces of the same size. The cut parts are fixed to the structure. These will be the paws. Using a spring (neck), a ball-shaped head is installed on the body.


The finished product is painted. The necessary details are completed: eyes, nostrils, mouth. According to this principle, you can create figures of other animals.

Making a flowerbed from a tire in the form of a flowerpot: instructions

The manufacturing technology of this product involves turning the tire inside out. This is why it is so important to choose tires with soft and thin rubber.

Main stages of work:

  • Cutting out petals.
  • Turning the tire inside out.
  • Coloring and decorative finishing finished product.

    • The shape of the petals can be absolutely any:

    • triangular;
    • rectangular;
    • wavy;
    • round;
    • in the form of leaves;
    • abstract, etc.

    These petals will subsequently be located along the edge line of the flowerpot.

    Markings using chalk or soap are applied to the top of the tire (on one side). Using a cutting tool (scissors or jigsaw), make cuts along the marked lines.


    Turning the tire inside out will require some skill and effort. To achieve the desired result, you need to turn the tire over with its whole side up, grab the product with your hands by the edge line of the cuts you just made located at the bottom, and, pressing on the tread, carefully turn it out. About halfway through the work, the tire should be flattened into an oval. After this, turning it inside out will become even easier.


    The last step will be painting the finished product in the chosen color. It is better if the shade is in harmony with general view plot. Solid colors look attractive, but a variety of colors will make the flower bed more impressive.


    Step-by-step instructions for creating and photos of flowerbeds from tires in the form of a flowerpot on a leg

    The easiest way to make a standing flower bed is to attach 3-4 legs to the previously described version of the product. To create them, you can use semicircular tire scraps (the area near the rim), bent pipes or fittings.


    To create a more stable flower bed, you can use a tire equipped with a metal disk. The technology of implementation is almost the same as in the previous case: the wheel is laid on a flat surface, markings are applied in the form of petals and cuts are made all the way to the tread. Both parts of the tire are turned outward.


    The elements are stacked on top of each other to create a large flowerpot on a leg. It needs to be painted before planting. Decorative design can be very diverse:

    • coloring the product to look like a flower (colored top, green bottom);
    • imitation of a concrete or metal flowerpot (depending on the color of the paint);
    • applying beautiful patterns or designs;
    • decoration using pebbles, glass, shells and other elements.

    Technology for creating a tea set from tires

    A tea set in the form of a cup and teapot is quite easy to create. For a kettle you will need three tires with different diameters. The largest tire is placed underneath. It will serve as the bottom. Two other tires are laid on top of it. Moreover, the smaller of them should be in the middle of the structure, and the one that is larger (but smaller than the bottom) is placed on top of it.


    To form the spout and handle you will need pipes. The spout is made from a drain with a curved shape. For the handle, a regular pipe with a diameter of 3 cm is suitable. It needs to be shaped like a hook. Having made these elements, they should be attached to the structure at the fastening points and mark the cut lines where they will subsequently be inserted and secured.


    The cup is made from three tires of different sizes. Take a pair of tires from a passenger car. You will also need a large truck tire. It will serve as the basis for creating a saucer. To do this, the top is cut off from the product. Both edges (outside and inside the wheel) are processed so that a flat part remains, resembling a saucer. It is slightly buried in the soil, and tires from a passenger car are installed on top (one on top of the other).

    The resulting tea set items are filled with soil into which flowers are planted.


    Making a flowerbed from tires with your own hands: video and recommendations for choosing flowers

    The flowerbeds, which resemble animals, are partly made from whole and cut tires. A flower garden in the shape of a swan is considered one of the most complex options making flower beds. It involves a method of turning the tire out. But at the same time, complex markings are made.


    Slicing with electric jigsaw must be precise and accurate. To make the bird's neck curved and fix it in this position, you should use a wire. The decor is done in such a way that the flowerbed looks like a swan. The beak is made separately.


    The following flowers are suitable for creating compositions with a combined height:

    • petunias;
    • marigold;
    • pansies.

    IN central part you can place dahlias, phloxes, plants with unusual shape and foliage. They will attract the eye and concentrate attention at the required point.

    Having tried simple ways making flower beds from old tires, you can move on to more complex structures. The tires are suitable for flower beds in the form of snails, frogs, parrots, zebras, bears, and turtles.