Make a hot stand from polyamide thread. Hot stand

A great idea for gifts is an impressive hot stand made by yourself. Ahead new year holidays, I have a lot of colleagues and acquaintances, but I don’t want to spend too much money. A solution has been found - make something yourself. Usually the raw materials for crafts cost pennies. This hot pad is made from a cork mouse pad and faux pebbles. But it is quite appropriate to use coffee beans, unnecessary coins, even corn, etc. instead of pebbles.

So, to make such a hot stand you will need:

cork mouse pad;
smooth black pebbles;
hot or epoxy glue.

Step 1. Take the first pebble you like, put a drop of glue on it and glue it to the center of the rug. Press firmly. It's okay if the glue comes out from under a pebble, it will be covered by the next pebbles.

Step 3. We continue to glue our kaleidoscope, varying the stones different sizes. You can allow yourself to glue a few pebbles onto an edge, or suddenly wedge in a pebble of a different color. In general, have fun with your health.

Step 4: As you approach the edge of the mouse pad, try to predict which stones will fit to complete the mouse pad. If the stones stick out beyond the mat, over time they may fall off, breaking the edge of the cork.

Step 5. Wait for it to dry completely and proceed to making the next hot pad.
If you want to use coffee beans instead of pebbles, the stand will make a noise when it comes into contact with a hot kettle. pleasant aroma everyone's favorite drink. Use your imagination and make stylish things with your own hands.

Such hot pads can be seen in large quantities in Crimean souvenir stalls. They are made from juniper and they sell very quickly. In conditions middle zone Of course, you won’t find juniper, but such a stand is very easy to make with your own hands from tree branches with a beautiful pattern on the cut. These are acacia, apple, plum, apricot, oak and ash.

You can make several of these stands in an hour. First, we need to select branches 3-6 cm thick. You can combine cuts from branches different thicknesses, it will be beautiful.

It is most convenient to cut a branch into cuts 4-5mm thick with a miter saw:

But you can cut the cuts with a hacksaw. It is advisable to sand each cut from the front side with sandpaper.

The bark can be scraped off with a knife, but this is not necessary, especially if the bark is tightly adjacent.

Now we combine a stand from saw cuts of different diameters (in my case). Front side facing inward:

However, it should be borne in mind that the fewer links, the easier it will be to glue the stand together. It is desirable that the round pieces of wood adjoin each other at several points. We glue the links of the stand together, placing saw cuts on top of several circles. To do this, coat the junction areas with PVA glue:

After making sure that all the links are interlocked, we send the stand to dry under pressure. I took a linen bag of sand, placed it on a stand and placed another bucket of water on top. The stand is glued together in 4-5 hours.

There is another manufacturing option wooden stand under hot. We cut out a circle from matting and glue cut branches onto it on both sides. It turns out very stylish and beautiful. Plus it's easier to do:

Please rate this post:

Hot stand

Life itself tells us DIY gift ideas. Life in the city takes place in a special rhythm, which forces you to do several things at the same time. So, many people have a snack while working at the computer. However hot dishes may damage the table surface. To prevent this from happening, you should purchase a stand for a hot cup or... you can make a stand for a hot cup with your own hands.

In addition, such a thing can be presented as a gift to a loved one or friend. A stand made by yourself will not only fulfill its immediate purpose, but will also become another reminder of warm feelings.

For a DIY stand you will need:

two old disks;
textile;
thin foam rubber or other material that can be used as a lining;
a bag of beads;
scissors;
a small piece of satin ribbon;
needle and thread.

Step 1

Fold the fabric in half with the right side facing inward. We place the disk on the surface, retreat two centimeters from its outer edge and draw a circle. There are two ways to do this. Firstly, using a compass, and secondly, using a ruler.

Step 2

Carefully cut out a circle along the resulting line. Since the fabric is folded in two layers, you need to make sure that these layers do not move (otherwise the edges will turn out uneven). It is advisable not to lift the lower blade of the scissors from the table surface; this technique will help to obtain the most even cut.

Step 3

From foam rubber or other soft material(for example, you can use an old knitted sweater) you need to cut out two circles, the diameter of which will be equal to the diameter of the disks.

Step 4

The resulting blanks must be folded as follows: we place a smaller circle in the center of the larger diameter circle, and place a disk on it.

Step 5

The edge of a circle cut from fabric is sewn with regular stitches, which are located at a short distance from each other. Then the edges of the fabric are pulled together using thread. You need to tighten it so that the fabric tightly fits the disc and the lining. Similar steps need to be taken to obtain the second half of the future stand.

Step 6

Cut a piece of about five centimeters long from the satin ribbon. We fold it in half, and sew the edges of the resulting loop to one of the blanks.

Step 7

The resulting blanks are folded together so that the side on which the disk is visible is on the inside. After this, the halves are carefully sewn together. To make the seam invisible, you need to choose threads that match the color of the fabric, and also try to make small stitches.

Step 8

The seam can be disguised using beads. To do this, you will need a special needle to work with the specified material. It has a small eye that can fit through the narrow hole of the bead. So, we fasten the thread, string six beads onto the needle, and fasten the thread again. We continue to sew the seam according to the indicated pattern until we complete the circle.

The work is completed. Now you can safely place a cup of the hottest coffee on your desktop without fear of ruining its surface.

If you are a fan of needlework and creativity, then you will be interested to know how to make a hot stand with your own hands. It is easy to make from materials available in the house. Even a beginner can master the technology. So, get acquainted with the options and choose the ones you like.

DIY hot stand: interesting ideas

If you decide to make such a souvenir, first of all decide which method is best for you. This will depend on your personal preferences and skills. Stands can be:

made of wood;
sewn from fabric using patchwork technique;
crocheted;
made of felt;
made from computer disks, buttons;
made using decoupage technique on ceramic tiles or wooden blanks.

Any of the ideas can be easily modified and has many options and interpretations. Choose, complement, create.

Use trunk and branch cuts

A very beautiful do-it-yourself hot stand made of wood, made from round pieces of the same or different diameters. It’s not difficult to prepare them, just regular saw And suitable tree. Apple and cherry tree cuts look good, as they have an original structure. But you can choose any option you like.

The operating technology is as follows:

Prepare cuts of branches with a diameter of 5-6 cm. If the bark fits tightly to the wood, it does not need to be removed. Be sure to sand the face of the rounds until smooth.
Make a composition from saw cuts. How less details, the stronger the product will be. In any case, the parts must touch each other in several places.
Connect the joints with glue.
For greater strength, the stand can be made of two layers. Accordingly, the planes of the cuts are also connected using glue.
Leave the workpiece under a load for several hours until the product is completely dry.

All is ready! If desired, varnish the surface, although the natural texture is no less beautiful.

Another way is to use one large cut, which can be decorated with burning, carving, contour drawing, watercolor ornament, followed by varnishing. If you don’t know how to draw, use decoupage (the technology will be described below). As you can see, one material can be used in different ways.

We sew a souvenir

You can also sew a do-it-yourself hot stand from fabric different ways. There are a lot of ideas. First, decide on the size and shape of the product. This can be a souvenir of a corresponding diameter, as well as a full-fledged rug or napkin. Both options are performed in the form:

vegetables;
fruit;
berries;
colors;
animals;
fairy-tale characters;
abstract patterns using patchwork technique.

If you've ever made potholders, the technology is similar. The product is made of two layers of thin fabric with dense material between them.

Felt is of particular interest. It is easy to work with, as it does not require overlaying the edges, because this material does not crumble. In addition, it is quite dense, and when using several layers of felt, stacked on top of one another for decorative purposes, no additional layer is required. Stands in the form of slices of oranges and lemons, animal faces, hearts and any other subjects are made from felt. This material is presented in rich color scheme bright colors, so there is a large field for imagination.

Beauty from old CDs

When making a stand, you need to take into account that it must be dense, durable and resistant to temperature. If you are going to use thin fabric on the right sides, a thick backing is a must.

You can very simply make a hot stand with your own hands from computer disks, which will act as a blank. The operating technology is as follows:

Take two disks and cut out circles from the fabric that are a couple of centimeters larger in diameter.
Place the disk on the fabric blank with the wrong side facing the disk (you can also lay it with a layer of padding polyester).
Sew stitches along the perimeter of the circle at a short distance from the edge (1 cm), and then pull the threads together. The disk will be “sewn” inside. Do the same with the second workpiece.
Take a strap of a length that is equal to the perimeter of the disc. Cover the part with braid or tape.
Connect all three elements by sewing two “covers” onto the strap.

The product is ready. Fast, simple and beautiful.

Knitted fantasies

Spectacular and original stand under hot water with your own hands can be done using this technique. As a rule, all products are knitted in the round according to the napkin principle.

To make such a souvenir, you just need to find the appropriate pattern, yarn and hook. If you are good at this technique, you can knit any product even without a pattern. Some people like to tie existing blanks, for example, the same computer disk, caps, stoppers, beads. Flowers and fancy geometric shapes are assembled from small parts.

Decoupage

This technique is suitable for those who are vaguely familiar with needlework or have little experience, but want to immediately get a masterpiece.

The point of the work is that on a dense base from a cut of wood or, for example, ceramic tiles(previously cleaned and degreased) a napkin (special or single-layer table napkin) with a decorative pattern is glued. After drying, the surface is covered with several layers of glue or varnish. back side ceramic tiles are covered with a layer of glued felt or fleece.

So, you have seen how to make a hot stand with your own hands. Choose what is closer and more interesting to you. Create table decorations or just Original gifts from scrap materials.

To make the kitchen more comfortable, craftswomen can make a hot stand with their own hands. This is not only a beautiful interior detail, but also a very necessary thing. Any materials will be used.

Tree

The advantage of using this material is that it is more durable than, for example, fabric. To make a wooden hot stand, made with your own hands, you will need:

Wooden blanks (sold in craft stores. You choose the shape at your discretion).
A simple pencil.
Washing gum.
Acrylic lacquer.
Paints, watercolors are better suited.
Brush.
A device for burning.

Let's get started:

To begin, draw on paper what a hot stand you make yourself should look like. It could be flowers, berries, an ornament or an inscription. The border around the edges, which serves as a frame, looks beautiful. Once you do this, it will be easier for you in the future. Now transfer the image with a simple pencil onto a wooden blank.
Take the burning device and wait until it heats up. When everything is ready to continue working, burn out the design.
If a simple pencil is visible in some places, be sure to wipe it off with an eraser, otherwise the work will look sloppy.
You can leave the design of the stand as is, just cover it with acrylic varnish, or you can continue to decorate it.
To do this, take paints and start decorating. Do this very carefully, because it will be difficult to get rid of errors. If you work with acrylic, then pay attention to the fact that in some places you will have to apply several layers to add saturation. Also, these paints can leak.
The stand must dry, and then it must be varnished and allowed to stand for several hours to dry completely.

Made with your own hands!

Felt

It’s even easier to make hot coasters from felt with your own hands. They give more room for imagination than wood. You can choose the color and design based on the style of your kitchen.

To create “citrus” coasters you need to take:

Different colored felt (orange for orange, yellow for lemon, green for lime, etc.)
Scissors.
Threads in colors matching the fabric or white.
A needle.
Pins.

What do we have to do:

Create blanks. For one fruit you need two large circles of colored felt (the size of a future stand), a slightly smaller white circle and eight colored slices.
Arrange the pieces in this order: large circle, medium circle and slices. Pin it with a pin.
Sew the slices around the perimeter through both layers.
To hide the seams, you need to sew a second large circle to the bottom one.

Everything is very simple! Create a few more of these “fruits” so that there is enough for all guests.

Idea

To create a stand for hot food, which you can easily make yourself, you can use scraps of felt. For this you only need one big piece, which will be the base, and several strips 5 millimeters wide. Length doesn't matter.

Take 3 different colors and place them on top of each other with a ladder, the indentations should be up to 10 millimeters. The beginning needs to be glued, now begin to tightly twist the strips with a snail, add glue if necessary. To complete the flagellum, make the inner strip 2 centimeters shorter than the outer one and secure it with glue, do the same with the middle one, only make it shorter by only 5 millimeters. Make as many snails as necessary to cover the entire base. Attach the workpieces to it using a heat gun.

Textile

To create such coasters with your own hands from fabric, you will need small scraps. You don't even have to go to the store to buy new materials; you probably have them lying around somewhere at home. So, for work you will need:

Fabric in eight different colors.
Sewing machine (if not, you can try to sew it carefully by hand).
Hexagon pattern.
Scissors.