Decorating the attic with wood in Japanese style. Finishing the attic floor - possible options and execution technology

Thanks to its non-standard geometry, there are many more design possibilities in the attic room than in any other room. Roof slopes can serve as a ceiling attic floor, and at the same time be its walls.
An exclusive interior can be created thanks to windows on the ceiling, or well located load-bearing beams. The functional purpose of the attic is also of great importance - interior decoration must correspond to him.

As a rule, the attic is located in a house with a pitched roof. It could be one steep and the other a gentle slope, or both gentle.
If two slopes are steep and their overhangs reach the ceiling, then it’s just an attic:

• To be able to turn it into an attic, the attic must be raised in height, due to a small wall around the perimeter of the house. A person should be able to walk around the attic without bending their head.

• There was a time when attics were unheated and were intended to house servants, poor students and poor intellectuals. Today, the view of this room has changed - it has become a full-fledged living space, subject to its high-quality insulation.
• Many of the materials used to produce interiors make it possible to install thermal insulation during their installation. Particular attention is paid to the roof slopes, because they take on precipitation, wind loads and the effects of low or high temperatures, depending on the season.
• In progress roofing works, thermal insulation of the roof is mandatory. In any case, if you plan to make a residential attic.
  Regardless of this, the same list of work on insulating the roof slopes must be performed inside. A double layer of thermal insulation guarantees the room protection from freezing and drafts.

As for the walls and gables (see), if they were insulated during the exterior finishing of the house, then there is no need to do this work inside. We will not go into details of the thermal insulation device; there are similar articles on our website.
In addition to them, watch the video. Let's just say that many materials used in the interior decoration of the attic themselves have thermal insulation properties- for example: plasterboard, fiberboard, cement-bonded and magnesite boards.

Attic floor installation

When installing a kitchen or bathroom under the roof of the house, the interior decoration of the attic floor must be appropriate. Since the attic room is quite spacious and has windows that allow it to be regularly ventilated, high level there will be no moisture in it.
So:

• The main attention when preparing for finishing should be directed to the floor, so that in the event of an emergency with water pipes, the ceiling of the room located on the floor below will not be damaged.

• Therefore, you need to try to create a sealed structure on the floor, and doing it yourself is not at all difficult. Consider the option of a brick or stone house, with reinforced concrete slab ceilings
  In this case, the implementation of waterproofing can be the same as in apartments.

• First, the concrete surface is treated with a penetrating waterproofing mixture, covering the wall to a height of fifteen centimeters. First of all, the joints of the floor and walls are coated, gluing a special insulating tape on top.

• When all corners and joints are sealed, the primer is applied to the rest of the floor surface. After the mastic has dried, you can make a self-leveling floor using a dry self-leveling mixture diluted with water.
  The result is a perfectly flat and airtight base for laying porcelain stoneware, tile or mosaic tiles.
• In principle, the floor can be made in exactly the same way in cases where it is planned to make a regular one in the attic. living room, only you can do without tape and replace the waterproofing mastic with a regular primer.
• But there are other options for flooring. It all depends on which decorative coating preference and whether the floor level needs to be raised higher.
  If necessary, then on top of the waterproofing layer, which can also serve as an ordinary roofing material covered with an overlap, they are mounted wooden joists.
• If the space between them is left empty and, for example, a plank floor is made over them, each step on the floor will produce a booming sound. Therefore, the resulting cells are filled with any bulk insulation: granulated penoizol, expanded clay or polystyrene chips.

• Thus, you can kill two birds with one stone: you will get not only insulation, but also good sound insulation of the floor. So: liquid cement mortar is poured into the cells with insulation - you will get an absolutely sealed foam concrete base, and its price will be minimal.

In order to lay tiles or laminate on such a base, you will need to embed the reinforcing mesh in the uncured mortar, and then apply a leveling screed. If a plank floor is installed, then the mesh will not be needed.
Work on installing the subfloor must be carried out after plastering the walls, if any.

Decorative finishing of the attic

If the external decoration of the walls was carried out without insulation or not at all, the walls and gables must be insulated from the inside. In this state of affairs, the most convenient option would be to interior decorate the attic with clapboards, MDF panels, plasterboard (see) or other material that requires installation of sheathing.
It is very convenient to install insulation into its internal space.
So:

• Most often, owners give preference to natural materials, and lining boards are number one on this list. And it is not at all necessary to sheathe absolutely the entire room - you can get by with just a plank ceiling or just wall sheathing.

• As for interior design, you need to use your imagination so that the room does not look dull and monotonous. And there are many decoration options.
  These are doors, baseboards and cornices in contrasting colors; beautiful carved railings on the stairs leading to the attic.
• This includes painting the plank surface in original colors, hiding the texture of the wood. Moreover, the painting is not monochromatic, but alternating light colors with darker ones, as in the photo below.

• It would seem: lining boards are the most affordable material known to everyone. How can you use it to do it in the attic? exclusive interior?
  It turns out it is possible! As proof, we give an example of designer finishing of such a room with a board.

• Let's see what techniques the designer used. First: the room is divided into zones by using boards with different sections - “block house” and “standard”.
  The boundaries of the zones are also determined by the roof rafters, which provide a contrast in color to the walls. To paint the board, a stain of a very pleasant shade was selected.
• Wall decorations are frames with canvas stretched over them. Or perhaps it is silk wallpaper glued to a plywood base, or directly to the wall, and framed with decorative molding.
• The window sill space is also decorated. The interior is completed with antique lamps and furniture - just look at one chest standing in the corner.
  And there seems to be nothing supernatural in the decoration, but the picture just attracts the eye.
• In order to “dilute” wood in the interior of a room, you can use a variety of finishing materials. In our next example, two of them serve this purpose: decorative rock, with which part of the wall is lined, and glass in the suspended ceiling.
  The contrasting decoration here is provided by beautiful twisted pillars and railing balusters.

• Sheathing the walls of the attic, with the same success, can be done with MDF panels. As in the case of lining, to achieve harmony in such an interior, it is important to avoid monotony.
  In this case, the lower part of the walls is decorated with panels with cork covering, used wooden skirting boards and slats of a darker color.

• Drywall is also successfully used in finishing the attic space. It is used to insulate and level walls, create suspended ceiling structures and wall partitions.
  And in this case, the design of the attic space will not be inferior to any other. Fortunately, the surface of gypsum board can be painted, covered with wallpaper, decorated with tiles or three-dimensional panels.

• If there is no need to insulate the attic walls, they can be leveled with regular or decorative plaster. Brick and cinder concrete walls are treated with a universal primer, then, after it dries, a starting layer of plaster is applied.
  After letting it set, the surface is primed again.
• The final layer of plaster can also be structural. The relief in this case is created by adding stone chips or other fillers to the solution.
  To achieve this goal, masters use and various instruments, with the help of which a relief is applied to the wall.

• Plastered walls can be simply painted, covered with floral wallpaper, or used in decoration for more expensive types wall coverings with veneer made of cork, bamboo, or stone.

• In the example above, the walls of the room are finished with one of these coatings. The highlight of the interior is small wall, lined with 3D panels with three-dimensional relief.
  The attic is also very decorated with beams mounted along the perimeter of the ceiling and roof slopes, which contrast with the decorative coating.

As you can see, there are many ways to perfectly decorate an attic floor, and we really hope that our little instructions helped you with this. Use your imagination, dare and delight yourself and your loved ones with a beautiful interior!

Almost every owner of a private home has attic room. Sometimes it is used as a warehouse for various things, sometimes it sits completely empty. But when the issue of expanding living space arises, many people think about the attic. After all, there is no need to add anything to the house - it is enough to insulate and equip the attic floor, and carry out the interior decoration of the room.

In this article we will demonstrate the most common options for finishing the attic floor, and also introduce you to the complete technology for performing the work.

To avoid unpleasant consequences, insulation and finishing of the penthouse is best thought through at the stage of designing the house. This will help you organize the execution sequence correctly. preparatory work. Unlike the construction and insulation of the attic floor, which must be carried out by specialists, it is quite possible to finish the attic with your own hands.

How to finish the attic inside: preparatory work

Before finishing the attic with your own hands, you should insulate the end walls of the attic space, as well as heat and vapor barrier the roof slopes.

Advice: The comfort of this room in the future depends on the quality of insulation and insulation. If a mistake is made at this stage, it can negate the entire cladding of the attic.

Selection of finishing materials

When the attic floor is reliably insulated, the question arises: how to decorate the attic from the inside? There are many materials for covering a room on the construction market - let's look at the most popular ones.

Lining

Plastic lining is one of the most inexpensive and popular materials for interior cladding of buildings. It can also be used to decorate the attic. The material gives ample opportunities in the implementation of room design, in the choice of color and pattern. Sheathing with plastic lamellas is done very quickly and does not require special installation skills. To the disadvantages plastic lining Its fragility should be taken into account - the material can crack from an impact.

Cladding the attic with clapboard (plastic)

On a note: If you want to give the attic floor special energy and comfort, use wooden lining to decorate it.

Advantages of lining from natural wood: unique colors, natural texture, environmental friendliness. Decorating the attic walls with wood allows you to create a beautiful and “warm” room that is pleasant to be in.

Among the disadvantages of wood: poor resistance to moisture and temperature changes. Therefore, use wooden lining for cladding the attic only if you are sure that the room is reliably insulated and insulated.

Beautiful attic decoration with clapboard: photo example

Recommendation: When working with any cladding material, strictly adhere to its installation technology. The better the work is done, the longer the finish will last.

Blockhouse

A good idea is to cover the house with a block house. Such a mansion will resemble a fairy-tale mansion, because the material creates an imitation of timber. Externally, the cladding of a house with a blockhouse looks like a real one log house. But this material has one advantage over natural wood - cracks do not form on such cladding over time. Blockhouse finishing is not afraid of moisture, and it does not require regular cosmetic repairs. The sloping shape of the blocks is already a decoration in itself, and the panels are tightly adjacent to each other.

The only drawback of a blockhouse is that such cladding “steals” several centimeters of attic space.

Elegant attic decoration with a blockhouse, photo

Plywood

If the question is how to sheathe the inside of the attic cheaply, then plywood is quite suitable for these purposes. As a rule, this material is used to level surfaces for finishing, but it can well serve as self-cladding. Among the advantages of plywood are lightness, ease of installation, cost-effectiveness, and strength.

Attention: plywood can be used to finish an attic space only if the humidity level and temperature meet the standards established for residential buildings.

Covering walls and ceilings with plywood is an excellent basis for wallpaper and textile finishing. And if plywood is used as an independent finishing material, then in order to protect it and enhance the decorative effect, you can coat the material with varnish or paint.

Varnishing plywood sheathing will highlight the texture of the material

Drywall

Many owners of private houses use finishing the attic floor with plasterboard. Among the advantages of covering with this material: its lightness, non-flammability, low cost. Using sheets of plasterboard, you can quickly level any surface, be it walls or ceilings. But, since in the attic there may be high humidity, then it is better to use moisture-resistant material for its finishing.

An example of what multi-level structures can be built - finishing the attic with plasterboard, photo

Advice: wires and various communications are often hidden behind plasterboard sheathing. But if the attic is located in a country house where you rarely visit, then it is better to lay the wires in special boxes. This way you can always get to them, and they won’t be damaged by rodents.

Plasterboard sheathing can be covered with wallpaper, putty, or decorated with ordinary or decorative plaster.

The illusion of floating in the clouds will be created by beautiful photo wallpapers - an option for finishing an attic, photo

Ideas for arranging different types of attics

To make the attic space original and different from hundreds of similar projects, you should use various decorative techniques in its decoration. Using simple design techniques, possible disadvantages attic structure turn into advantages.

Features of finishing the attic floor of a wooden house

Attic in wooden house requires a more careful approach to its finishing. But if you properly prepare the ceiling and wall surfaces, you can use almost any material for cladding. Photos from our gallery will demonstrate more clearly how the interior decoration of an attic can be done in an original way.

The interior of an attic in a wooden house can be designed not only in country or Provence style. You can also use bold decisions, for example, decorating an attic in a loft style. But how to cover the attic from the inside?

As for finishing the attic wooden house or a dacha, it either consists entirely of wood or includes wooden elements.

A combination of several materials for covering a room looks impressive.

Since the room under the roof contains a certain amount of romanticism, fabrics will look appropriate in its design. These can be draperies with motifs that repeat the pattern upholstered furniture, or a canopy over the bed in the attic bedroom.

Textiles in finishing attic rooms, photo

Ceiling design methods

Depending on the design mansard roof, the ceiling in the attic may have different shapes, slope, sometimes may be completely absent. Therefore, it is difficult to select materials for its cladding. They may be the same as for wall decoration, or they may differ.

Add volume and beautiful view in the attic room you can use stretch ceiling. Sheathing with plasterboard allows you to create a multi-level structure that diversifies the interior of the room.

Using a stretch ceiling you can create the effect of a starry sky

You can make the attic at your dacha unusual by painting wood paneling ceiling and walls in different colors. They can be plain or with ornaments.

Painting a room in which no more than three colors are used looks harmonious.

Attic cladding: cost of the issue

When asked what is the best way to decorate an attic to make the room look luxurious, there is only one answer - natural wood. And plywood and lining will help you save money on covering the attic floor.

Finishing the attic with plasterboard: step-by-step instructions

You can finish the attic floor yourself. In this section we will describe how to cover an attic with plasterboard.

Since the attic space is located directly under the roof, it is often exposed to atmospheric influences: rain, wind, snow, scorching sun. Therefore, before finishing the attic inside, you need to take care reliable vapor barrier and insulation of the structure, paying attention Special attention roof thermal insulation.

1. To cover the attic with plasterboard sheets, you need to build a frame. For this purpose they are used wooden blocks or metal profiles. They are installed in increments of 40-60 cm.

The first profile is fixed level

1. After the horizontal profiles are installed, begin marking and fixing the vertical ones.

CD profiles are attached in increments of 40 cm

On a note: in a small attic space, finishing the attic with plasterboard can be done without installing a supporting frame.

1. If there is a horizontal roof, they first start covering the walls and gables, and finally the ceiling. If the roof is sloping, the slopes are sheathed first. To do this, screw the sheets of drywall to the frame with self-tapping screws, which are screwed in at a distance of approximately 25 cm from each other.

Important: during the finishing process, gaps of approximately 0.5 cm are left between the sheets of drywall. This is necessary so that they can withstand minor vibrations of the attic during strong winds and snow.

To securely fasten the cladding material, each self-tapping screw must enter the slab at least 1 cm

1. After all surfaces are sheathed, the gaps between the sheets of drywall are puttied.

An additional reinforcing mesh can be applied to the joints between the plates, and the joints with other materials are treated with acrylic putty

After covering the attic with plasterboard, they begin to finishing. This can be puttying and painting, wallpapering.

More details about finishing the attic with plasterboard - video:

Bottom line

The space under the roof can become additional living space in the house. There are many options for its use - as an office, a bedroom, a nursery... Depending on the purpose for which the floor is intended to be used, the interior lining of the attic is selected, which will give the room a complete aesthetic appearance, making it cozy and comfortable for living.

An attic is essentially an attic space. It differs from an ordinary attic in that it is located in a building with pitched roof, consisting of: one flat and the second steep part. They give home additional area, which can be used for living space.
This roof design was developed by an architect from France named Mansart, from which the word “attic” was derived.
In those days, these premises were the abode of students, poor creative intelligentsia, and servants. And all because the attics were not insulated and were poorly protected from moisture.
But the situation has long changed: thanks to the development of the construction industry and the latest design developments, the attic space has become a full-fledged addition to a residential building. Now you can arrange almost any room in the attic space, even a kitchen and a bathroom.
Naturally, the methods of finishing attics and the choice of materials will depend on this. But before finishing the attic from the inside, you need to consistently perform several preparatory works, which we will tell you about now.

A well-made roof of a building does not guarantee that the attic will be warm and dry. To achieve this, all its surfaces need to be insulated.
The technology for this work will depend on whether external thermal insulation of the roof was performed during the construction of the house:

• If yes, then it will be easier to additionally insulate the slopes: you can simply hem them with fiberboard, clapboard or plasterboard, laying them under the sheathing thin layer polyethylene foam or isolon. It is better to use foil options, they prevent the formation of condensation.

• Well, if the roof slopes were not insulated, you will need to do this work from the inside. Then insulation and finishing of the attic will require the sequential laying of several layers, the first of which will be a waterproofing membrane.

• The waterproofing film is fixed with counter slats directly to wooden sheathing roofs. Only after this will it be possible to lay the thermal insulation.
  To insulate roof slopes, it is better to choose soft, and as thick as possible, roll insulation.
• Slab materials are not very suitable for this, especially if the roof is hipped or has another complex configuration. They are best used for wall insulation.

• The method of attaching the thermal insulation layer depends on the roof structure. If there is a small step between the rafters, you can choose a material whose width is slightly larger than this distance.
  Then the insulation fits tightly between the rafters and does not require additional fastening.

• When the distance between the rafters is large, bars with a small cross-section are used to attach the insulation. In this case, first a wire is pulled between the rafters, fixed with self-tapping screws, and insulation is already laid on it.
  The best way is to watch a video on this topic.
• If you use regular mineral wool, then you will need to stick a vapor barrier film on top of it, and only then secure this entire structure with bars. It is much easier to use a material with a ready-made vapor barrier layer.

• When insulating attic walls, you can do without a waterproofing layer, but only if you use polyurethane foam materials as insulation.
• Mineral wool tends to get wet and rot. It is better not to use polystyrene foam for this, because it is highly flammable and quite toxic when burned.
• It is very good if there is a gap between the waterproofing and the insulation to ensure ventilation of the insulation. When doing the work with your own hands, do not forget that all wooden structural elements must be treated with an antiseptic composition.
• If your house has external thermal insulation of the walls, then the attic gables will not need to be insulated. But it’s still better to insulate the floor, especially if there is a sleeping area in the attic.
• For floor insulation it is better to use bulk insulation: Expanded clay or expanded polystyrene crumbs are very convenient, and the penny price of the material allows you to significantly save your budget.
• The floor is covered plastic film, install wooden logs, and pour insulation into the resulting cells. It is filled with liquid on top cement mortar, in which the reinforcing mesh is embedded.
  You can find more on the Internet detailed instructions on the construction of such a floor.

When the solution has set, it will be possible to make a screed, and the floor will be ready for further finishing.
This method of floor insulation creates excellent sound insulation, as well as reliable waterproofing of the room. You can even install a bathroom or kitchen in the attic without fear that water will leak down.
An example of finishing an attic floor for a bathroom in the photo above.

Decorative finishing of the attic

Naturally, the interior decoration and insulation of the attic depend on how you will use this room. Most often, a living room is arranged in the attic space: a bedroom or a children's room, although there are exceptions.

Wood in attics

Reflecting on the question: “What is the best way to decorate the attic?” - you start going through everything possible options. And the first thing that comes to mind is a tree.
Most likely, this association occurs because bearing structures the roofs are made of this material.

• In addition, finishing the attic with wood creates additional thermal insulation, as well as a unique microclimate filled with woody aroma. No other type of finishing material can compete with the remarkable properties of natural wood - that’s a fact.

• Clapboard, which is most often used for finishing works, It is the most simple option sheathing.
  There are five types of profiles of this board, and several standard sizes. Its installation can be done in various ways.
• The location of the board on the surface can be horizontal or vertical, diagonally, in a circle, or herringbone. This creates a specific pattern and breaks the monotony of the surface.

• Using lining as a finishing material, you can zone the attic by painting each zone in its own color. The picture above is a very good example of such an interior solution.
  Columns with beautiful decoration also play a significant role in this.

• Finishing the attic with wood can be done in another way - using wooden panels. They can be made either from solid wood or in the form of stacked slatted panels from the same lining.
• It can be MDF options covered with wood or bamboo veneer. How a budget option, laminated and veneered fiberboard panels are used.
  Wooden panels are good both for wall decoration and for installing suspended ceilings.
• The attic is finished with MDF panels if this room is used as an office or sports room. It is not customary to do such cladding in bedrooms - the interior will be associated with some kind of office.
  Therefore, they are combined with other types of finishing, such as wallpaper, decorative plaster and painting.

Few people know that a new finishing material has appeared on the construction markets - wooden wallpaper. They are a set of panels made of profiled wooden elements, glued to the base.
For the production of this wallpaper, mainly coniferous wood is used. Their thickness does not exceed two centimeters, with a width of 1.2 meters and a length varying from two to six meters.
Such panels are glued to the wall, like regular wallpaper, and allow you to quickly and beautifully decorate a room with wood.

Ceiling beams

The main decoration of the attic interior can be ceiling beams. Depending on the roof structure, these beams may be load-bearing, rather than hollow false beams that are used in ground floor rooms.

So:

• Rafters can also play this role - just decorate them carefully. The examples we have given of finishing the attic floor, using ceiling beams, clearly show how beautiful and original it is.

Wherein decorative finishing walls can be the simplest - all attention is attracted to beam structures, which always have a contrasting color in relation to other surfaces. Original ceiling lamps, in harmony with the beams, also play a big role in such an interior.

Plasterboard structures

As we have already said, there is nothing in the attic space that could interfere with the implementation of any structure: partitions, columns, arches, suspended ceilings. The main thing is that it is spacious.
You can divide the room into zones using any of these elements.

So:

• The final finishing of attics lined with plasterboard can be a surface painted with acrylic paint and covered with wallpaper. Often the attic has good height- this is what most apartments in multi-storey buildings lack.
• Sometimes it even needs to be hidden, so dropped ceilings made of plasterboard can have several levels and deviate from the base surface not by 10-12 cm, but much more.

• In design projects, there are even suspended ceilings in the attic. In the top photo, walls are made of plasterboard and tension glossy ceiling milky color, create wonderful interior living room.
  This is facilitated by good natural lighting in the attic.
• Not all attic spaces have sufficient quantity windows If there are no windows in the roof slopes, but only small windows on the gable walls, in terms of lighting you have to rely more on lighting fixtures.

That is why the finishing of the attic is clean, done mainly in light colors. Only some interior elements can be dark.
The example above shows a very popular technique for finishing a wall as an extension of the ceiling. It looks like this: along the head of the bed, which faces the wall, a strip of wallpaper with a thick pattern is pasted.
The pattern usually contrasts with a light surface and visually elongates the room in height.

Other types of finishing

Designers constantly come up with ideas that may seem unusual. But that’s what’s different designer finishing.
And often, for interior design attics, use those materials that are intended for external decoration of facades.

So:

• This includes materials such as vinyl and aluminum siding, various types of composite panels, and HPL plastic panels. Some manufacturers even offer complete options designed specifically for finishing the attic.
• Such kits are made for a specific object, according to preliminary measurements - this is called individual design. In this case, fine finishing The attic is an assembly of a certain structure, which is carried out quickly and without unnecessary dirt.

• Attic walls lined with HPL panels look especially good. These are anti-vandal façade panels made from plastic high pressure, have extraordinary strength, dielectric and thermal insulation properties, and practically do not absorb moisture.

• The production of this material is carried out simultaneously with the pressing of the top decorative layer. As a result of this technology, compact, non-porous, hygienic panels with a strict geometric shape are obtained.

There are options with double-sided finishing, and different ones. So the surface design can be created by simply turning the panel one way or the other.
We told you about the most interesting options finishing attic space, but the choice, of course, is entirely yours.

Over almost 200 years of existence, these premises have undergone tremendous metamorphoses: from semi-attic housing for the poor to luxury apartments in high-rise buildings. Large and small, in the city, in a country cottage, in the country, modern, decorated with trendy materials, and traditional, lined with wood.

If you plan to decorate the attic with your own hands, the unusual geometry and broken shapes of the space are perplexing, but at the same time they attract, force you to include creative thinking and all your creative potential. Finishing the attic floor is a fascinating process; a tribute to tradition and the desire to purchase modern housing are intertwined in it. In the article we will talk about how to decorate the attic inside, what materials are preferable for this, and how to use finishing to turn the specifics and shortcomings in the attic floor project into advantages.

How to decorate the attic from the inside

The living environment dictates its conditions in the decoration of the attic; in the city, the interior is subordinated to the lifestyle of the metropolis, this is more and more ordinary apartments under the roof, finished with plasterboard, plaster, wallpaper and others modern materials. But in a country house or dacha, wood is traditionally used to decorate the attic floor. Design of the attic floor, which is based on natural materials, this is not even a tribute to fashion, but a way to get closer to nature, to emphasize the originality and colorfulness of your own home.

Interior decoration of the attic, photo of a combination of cladding with imitation timber and lining

Tree - warm material, it breathes, the beautiful texture is a decoration in itself. Today you can choose from different breeds wood, if more expensive, with a pronounced texture, then ash, oak, larch, simpler - linden, pine and other conifers. The woodworking industry is keeping up with modern trends in construction and repair, so the market is flooded with all kinds of offers: plywood, corrugated wall panels, imitation timber, blockhouse, lining.

Please note that all wood requires additional processing before cladding. So that the attic finishing with wood lasts for a long time, has not become infected with fungi, and has not become deformed from exposure to the specific microclimate in the attic, impregnate it with antiseptic and fire-resistant compounds, and then on the back side, and especially the ends, with 2 layers of PVA putty.

Important: All materials have a length from 2 to 6 m, which allows you to choose the board size for finishing that suits the size of your room, so that there is as little waste as possible.

Finishing the attic with a blockhouse, covering the cladding in light tone allows you to use solid materials even in small attics

Lining

Lining is the most popular material for finishing the attic, a comfortable, shaped strip with a polished surface. For interior cladding, two types of lining are used: strip, which is mounted end-to-end, and eurolining - tongue-and-groove strip, 1.25 cm thick, 9.6 cm wide with a lock, tongue-and-groove lock. Along the back wall, along the length of the board, there are two recesses for condensate drainage. Suitable for finishing both large and small attic spaces. The light weight of the lining eliminates significant loads on the attic rafter system, therefore it allows even the ceiling to be sheathed.

Block house

A blockhouse is a modern imitation of a log, a segment with a convex upper part, 2.2 - 4.2 cm thick, the greater thickness is due to the arched shape of the material. The width of the blockhouse is 9.0 - 19.5 cm, wide beams are used for finishing large attics, while narrow beams are suitable for cladding small attic rooms. Equipped with a tongue-and-groove lock, usually mounted horizontally. Blockhouse cladding gives the feeling that the room is built of logs.

Finishing of attic rooms, photo traditional technologies cladding and competent addition of color

Imitation of timber

Imitation timber is such a large lining, like Gulliver in the land of Lilliput. Premises decorated with this material acquire a monumental appearance and solidity. The boards are equipped with a tongue-and-groove lock, up to 19.5 cm wide and 2.0 – 3.5 cm thick. Relevant for finishing attics large area, or in combination with lining and blockhouse. Due to the relatively large weight, imitation timber is rarely used for cladding the attic ceiling.

Separately about drywall

Remember the slogan: The people and the party are united! This is how drywall and repairs are inseparable; it is an almost universal material that can be used to quickly repair and level surfaces. In addition, the specific characteristics of the material make it possible to make a structure of any shape from it, so plasterboard is indispensable both in simple repairs and in the implementation of complex design solutions: arches, niches, elaborate volumetric figures.

For finishing attic rooms you should use moisture resistant drywall. Drywall needs finishing, which on the one hand adds costs, but on the other hand, opens up endless possibilities for attic design. Surfaces finished with plasterboard can be covered with wallpaper, decorative plaster, stone, cork, bamboo, or painted with textured paints.

How to cover the attic from the inside is a matter of aesthetic perception and wallet. We'll share practical advice, how to cover an attic with plasterboard, blockhouse, imitation timber, clapboard, and we will suggest some interesting and useful ideas like using a combination ordinary materials and different cladding techniques to transform a dull, standard finish into an exclusive and original interior.

An important digression from the topic

Not a single finish will last you more than a season without preparatory measures. Whatever the attic floor is built from, it is imperative to carry out thorough waterproofing, then lay a layer of thermal insulation, which should be covered with a vapor barrier membrane.

Particular attention should be paid to insulating the attic, if this is a summer house in the country, it is recommended to put at least a layer of polystyrene foam, warm rooms require integrated approach to the construction of a thermal insulation cake. It is difficult to overestimate the role of the roof in the arrangement of the attic - it is the main element of the entire structure, so be sure to inspect the vaults for leaks and once again check the quality of the roofing material.

Work order

Finishing the attic always starts from the bottom up. First the bottom wall, then bevels to the desired height. Next stage– finishing of front walls. Next is finishing the floor, and finally – the attic ceiling, if provided.

Lathing

Cladding the attic with imitation timber and a wide blockhouse does not require lathing. The materials are rigid and can be nailed onto the joists. As a rule, they are mounted parallel to the floor.

But before you line the inside of the attic with clapboard or plasterboard, you will have to make a sheathing around the perimeter for convenient and reliable fastening of materials.

For sheathing with plasterboard, the sheathing is made from metal profile. The racks are first installed vertically, nailed onto dowels, the distance between sections is 50-100 cm. Then the transverse bars are mounted for rigidity.

Finishing the attic with plasterboard, photo of the sheathing, the sequence of the sheathing is also visible: bottom to top

For clapboard cladding, the sheathing is made of wooden blocks with a cross section of 20*40, 40*40 mm. The bars are installed vertically at a distance of 40-100 cm from each other, for horizontal paneling, and parallel to the floor if the paneling will be mounted vertically. For additional heat and sound insulation, as well as for ease of installation of the slats, if a figured installation is planned, it is better to cover the sheathing with plywood or OSB, MDF, chipboard.

Be sure to nail the bars around the perimeter of the windows, doors, floors, at the joints of the slopes, in the corners, and at the highest point to which the finishing will reach.

Lathing made of timber and the sequence of horizontal cladding with clapboard

Clapboard finishing, a few ideas

In this article we will not teach you how to properly nail the lining; if you have taken up the cladding yourself, then you probably know how to hammer nails and screw in self-tapping screws. But we will dwell in detail on the question: how to decorate an attic with your own hands. Be sure to watch the video, where the finishing of the attic with clapboard is discussed in detail; the photos will illustrate the main stages of the cladding.

The simplest option is horizontal cladding of the attic with clapboard, starting from the bottom, joining the tongue and groove, increasing the height of the rail by rail. Either vertical cladding, starting from far corner, having straightened the first rail in level, the correct geometry of the entire lining depends on this. The lining can be attached to nails, which are driven into the tenon at an angle, or it can be clamped with clamps, but this will require additional expenses. All lining joints are covered with special overlays, in the corners - with corner strips. By covering the attic in this way, you will get a simple, quite traditional wood finish.

Lining is “plasticine” in the hands of creative and creative people. The options for finishing the attic, the photos demonstrate this well, are limitless. If you gravitate toward beauty and originality, you will have to work hard, but the result will be much more impressive. For example, the lower part of the walls can be sheathed vertically, this way you will visually raise the height of the attic, and the upper slopes – horizontally. Graphics will appear in the interior of the attic room.

Non-standard decoration of attic walls, figured lining with clapboard allows you to create an interesting interior using simple materials

You can also divide the length of the walls into odd parts so that you start and end the cladding in one direction. Decorate one section vertically, the other horizontally. If your attic is elongated, then long wall can be divided into three zones, the two outer ones sheathed vertically, the middle one horizontally, this design technique will not only straighten the geometry, but also help to correctly zone the space. Examples beautiful finishes and the design of the attic with clapboard, see the photo gallery.

How to properly sheathe an attic with plasterboard

Most quick way sew up the surfaces - finishing the attic with plasterboard, video tips will help you understand the intricacies of such cladding.

The sheathing should begin from the bottom, from the side walls, then the slopes, then the front walls. The process of installing drywall is simple and comes down to three steps. Cut off stationery knife sheet of the required size, install it close to the frame, and screw it with self-tapping screws every 20 cm.

Next, all joints should be sealed with putty, reinforcing tape should be applied along the seams, which is covered with another layer of putty. The surfaces are primed with an adhesive compound to increase the adhesion of the materials. After drying, you can begin finishing and arranging the attic.

Some lyrics

Whether it is finishing the attic floor of a wooden house, or a room made of brick and concrete, the combination of different materials and textures in the cladding always looks more advantageous compared to uniform wall cladding. In the article, we tried to figure out step by step what materials to use and how to cover the attic with plasterboard and clapboard. This is the basis on which all cladding principles are built.

There are countless options for finishing the attic floor; combine clapboard finishing with stone, blockhouse, or imitation timber. On one wall, make a semicircular niche from plasterboard, paste wallpaper with a landscape inside, cover the arch with blockhouse, as a result you will get an accent spot that will set the tone for the rest of the interior of the bedroom or living room in the attic.

Using plywood and plasterboard, you can create a semicircular frame; it will radically change the appearance of the attic; to enhance the effect of the arc, you can line it with clapboard

Beautiful and practical attic decoration can turn it into a cozy living room. This could be a bedroom, a study, a recreation room with billiards, a home cinema room, or even a children's room. Materials for finishing the attic can be either traditional: lining, blockhouse, imitation timber and other finishing options made of natural wood, or modern and non-standard: drywall, siding, plywood, decorative plaster and cork panels. Today we will present to your attention the most successful attic finishing projects, tell you in detail how to decorate an attic with your own hands, offer more than a dozen visual images of a beautiful one, and also show an educational video describing the finishing work process.

Interior decoration of the attic with clapboard: photo examples

Wooden lining - This is perhaps the most favorite and popular option for finishing the attic. Natural wood has a unique flavor, natural beauty and unique colors. Wooden paneling makes the room cozy and “warm”, giving it a unique touch of provincial romance. In addition to the fact that finishing the attic walls with clapboard looks beautiful and rich, it is also a very practical cladding option, since it is easy to care for. We invite you to take a look at the most original finish attic rooms, the photo below will demonstrate options using both lining and other finishing materials.

Natural wood is very elastic. This is another reason why lining is chosen as finishing for attic spaces. Under the influence of wind, the upper part of the house often moves. This process is invisible to the eye, but if the interior decoration of the attic roof were made of brittle and inelastic material, and without compensation gaps, this could lead to cracks.

Advice Strictly follow the installation technology of the selected finishing material so that the interior decoration of the attic holds up well and lasts a long time.

Finishing the attic floor of a wooden house and cottage

In addition to lining, there are other options for finishing the attic floor. In fact, if the surface of the walls, ceiling and floor is properly prepared, you can decorate such a room with any finishing materials and maintain it in any style. You have already seen how unusual and varied the interior decoration of an attic can be; photos from our gallery clearly demonstrate this. And if you want to learn in more detail about the choice of design and furnishings, be sure to have the correct layout. Such a room does not necessarily have to be maintained in rustic style. Even strict high-tech may be appropriate here.

Combined finishing of the attic floor in Hi-Tech style: plaster, wooden panels and wallpaper.

The interior decoration of the attic of a wooden house or cottage, as a rule, is carried out either entirely on the basis of wood, or with the inclusion of appropriate elements. But no one forces you to follow this cliché. Trust your taste and let your imagination run wild. Let the decoration of the attic in your home not be similar to hundreds of others that are most often offered in this case.

Idea Decorate the walls of the attic with inserts made of fabric that repeats the pattern of the furniture upholstery, and drape the ceilings with a monochromatic material that matches the color. The impression of softness can be enhanced by constructing an airy canopy over the bed.

Insulation and finishing of the attic with plasterboard

Before you start thinking about how to decorate the attic from the inside, you should think about reliable insulation and vapor barrier of walls. The room, located directly under the roof, is constantly exposed to cold wind and precipitation, and in the summer it becomes very hot under the scorching rays of the sun. Detailed material about the installation of insulation and vapor barrier film is waiting for you here - "".

And now we suggest you move on to finishing the attic ceiling. This part of the room may have a different shape and slope, and sometimes be completely absent. But if there is a ceiling in the room, the question arises: how can you decorate it beautifully? It is not necessary to use the same materials that you used to decorate the walls. You may be surprised, but you can even make a suspended ceiling in the attic!

Idea With the help of a stretch ceiling, you can visually lift an attic space, which usually suffers from a lack of space. Design, for example, a blue sky above your head, and complement the effect with stylish lighting.

Great option - finishing the attic floor with plasterboard. This material has a number of advantages: it is inexpensive, easy to use, relatively lightweight, and non-flammable. Using drywall, you can quickly level the walls and ceiling, and also create a universal base for any type of attic finish.

Many craftsmen also recommend using plasterboard sheets to disguise utility lines, in particular electrical wiring. Indeed, it is easy to hide all the wires behind such casing. But we are talking about a country house or dacha, where, unfortunately, rodents often live.

Important Lay wiring in a wooden house or country house open method, that is, in special boxes to ensure access to it. If wires hidden behind drywall are chewed by mice, you will have to disturb the finish to get to the problem.

If you want to know how to finish an attic with plasterboard, the video below will help you understand this issue in detail.

How to decorate the attic inside with wood, plywood, siding

Lining- This is not the only type of cladding using natural wood. The design of the walls in the form of imitation timber or blockhouse looks very nice. Blockhouse is wooden blocks convex shape. The wall covered with them looks as if it was made of rounded logs.

How to decorate an attic in a country house so that the interior looks unusual and original? Try painting the wood paneling on the walls and ceiling in different colors, or come up with an interesting pattern. By the way, designers recommend using no more than two or three primary colors to decorate any interior, otherwise there will be a cacophony.

Plywood and siding- These are the most economical options for finishing the attic. But if you are more interested not in the question of saving money, but in how beautiful and rich the room will look, there can only be one answer to the question “what is the best way to decorate the attic” - natural wood.