How to make a flexible baseboard for floor or ceiling. An unusual solution for unusual rooms: flexible skirting boards for the floor How to make a skirting board for a round wall

Decorating any room is phased implementation certain steps using various construction and finishing materials. And if you beautifully decorate the walls, floors and ceilings in a room with a standard geometric shape- the science is clear, then with the decoration of rooms with corners irregular shape, columns, curved sections and other decorative elements - a real test for a novice master. For beautiful design At the junction between the floor and the walls, in some cases it is even necessary to use a flexible plinth.

Flexible plinth, as the name implies, due to its ability to bend well, is ideal for finishing rooms with unusual shape walls, corners - round or polygonal. It especially makes the work of builders who design columns easier - a favorite decorative or load-bearing element. Even if you connect very small pieces of ordinary dense plinth to each other, you still won’t be able to finish the joint between the floor and the walls beautifully and neatly. Only a flexible plinth, which is also called plinth tape, can achieve an ideal bend.

Bendable plinth - a variety of options

On a note! If you use high-quality connecting materials when installing a flexible plinth, you can achieve a perfect fit of the profile to the entire bending surface.

The benefits of using skirting tape are given below.

1. Installation of the profile is quite simple. At the same time, during operation the material adheres well to the surface. Preliminary preparation other than pruning is not required.
2. Light weight and small size, which makes it easier to transport and work with the material.
3. Strength and resistance to mechanical damage.
4. Easy to maintain and long service life of all types of material.
5. Resistant to moisture and fading.
6. Non-toxic, high fire safety.
7. Rich colors and lots of variations.

On a note! Among the variety of skirting strips, there are also those that make it possible to use this element for laying and masking wires along the walls. These types of flexible skirting boards have special cable channels.

The only disadvantage of a flexible baseboard is its fear low temperatures. Of course, it does not collapse under their influence, but it loses its flexibility and can break under mechanical stress. Therefore, it cannot be used outdoors.

flexible floor plinth

What materials bend? Types of skirting boards

What can a flexible plinth be made of? Not just any material is suitable for this. So, it must have elasticity, that is, it must bend quite easily without breaking.

For the manufacture of flexible skirting boards the following can be used:

• Cork tree;
• polyvinyl chloride;
• polyurethane;
• « liquid tree».

The latter type of material is rarely used, since it is very difficult to work with and its price is prohibitively high. Liquid wood hardens very quickly upon contact with air. It’s easier to use other, more familiar to modern man materials.

Flexible plastic skirting board

Plastic is a broad concept; it combines several types of polymers. And the flexible plinth is made of polyvinyl chloride. By the way, regular plastic skirting boards are also made from the same polymer.

On a note! Regular PVC skirting board also has good flexibility. But it has longitudinally located ribs necessary for its installation, as well as a dense cable channel. Both make it quite rigid and do not allow it to bend easily. However, there are ways to bend an ordinary plastic skirting board on one's own.

But not everyone’s experiments go smoothly, so most people prefer to simply purchase a special flexible baseboard. It consists of a long strip laid in a roll - hence the name “plinth strip”. The material bends easily and can take any shape.

Flexible PVC skirting board has a lot of color variations: you can buy it in white or Brown or pick it up under a tree or stone. There are other color options.

The installation of such a plinth depends on the type of element. For example, self-adhesive options are available, and there are also those that are mounted using a special base and require pre-heating in hot water(about +70 degrees). The base itself, made in the shape of the letter P, is attached to the surface using self-tapping screws.

On a note! It is best to additionally glue the first version of the plinth tape " liquid nails"- the connection will be more reliable.

The undeniable advantage of plastic flexible plinth is its price. Compared to other types, this one is the cheapest. However, it is usually used to decorate joints of surfaces with a small radius. By the way, such skirting tape can also be used to seal the gap between the wall and the bathtub (sink), between the countertop and the wall in the kitchen.

Some time ago, this type of flexible plinth came into fashion. Cork borders, externally covered thin layer valuable lamellas tree species, have an elegant appearance and look not only stylish, but also expensive. That is why they are often used to design curved areas.

The advantage of cork plinth is its environmental friendliness, because natural material is used to make the element. Cork is also very functional and easily takes any given shape, which allows it to be used to decorate even complex interior elements. Since this plinth has excellent adhesion to adhesive compositions, its installation consists only of tightly pressing the material with applied glue to the wall. It is best to use liquid nails.

By the way, before attaching the element, some of its types will have to be varnished. But the cork plinth can be given the desired color by covering it with a coloring compound before varnishing.

Attention! Cork plinth cannot be used to decorate the joints between the wall and the floor in rooms with high level humidity.

Cork plinth looks great in rooms with finishing made natural materials. It goes well with regular wooden baseboards, textured wallpaper, and cork flooring. Its disadvantage is its high price.

Soft wood plinth

Despite the complexity of use, it is impossible not to stop at a material such as liquid wood. It is interesting that such a plinth is made on the basis of the most common durable wood- ash, oak and other species. However, the manufacturing technology is quite complex. Wood raw materials are exposed to special substances, acquiring a jelly-like consistency, while the substance manages to retain its natural color characteristic of wood. This composition hardens when exposed to air. The consistency of liquid baseboard resembles rubber.

It seems that the installation of such skirting boards is quite simple: they are one by one freed from individual vacuum packaging and are simply applied to surfaces. But the whole difficulty lies precisely in the process of correctly and beautifully laying the mass. It will no longer be possible to correct errors after the baseboard has hardened - only replace it. And this is an expensive pleasure.

Prices for flexible plinth Arbiton

Flexible plinth Arbiton

Flexible polyurethane

There are types of flexible skirting boards made from polyurethane. They are also known as rubber ones. In general, this type is no different from ordinary skirting boards, but does not break when bent. This was achieved by adding rubber to the original substance during the production of products.

On a note! The polyurethane flexible plinth easily bends along a radius of 50 cm.

Polyurethane baseboards are not afraid of water, so they can be installed in the bathroom. It is also highly durable, easy to use, and non-toxic. It can be painted in any color you like and thus match the interior. For painting, it is better to use acrylic-based paints, and the process itself is carried out after installing the product. Installation of such a plinth is carried out using special glue.

Dimensions of flexible plinth

Depending on what the flexible plinth is made of, it may have different sizes and release forms.

Table. Dimensions of flexible plinth.

These dimensions are due to ease of transportation and installation. Among PVC products, the most common are skirting boards with a height of 50-60 mm and a cross-section of 20 mm. They are most convenient to use for installation in apartments.

Calculation of the required amount of plinth

Calculating the plinth is quite simple. The first step is to measure the perimeter of the room in which the baseboard will be used. In this case, all measurements should be made very accurately. The result obtained is recorded.

Advice! It is most convenient to draw a diagram of the room, taking into account all the corners, niches, columns, doorways and sign each measurement separately. This will help you evaluate correctly required amount the whole plinth and allow the formation of as few joints as possible during installation.

Next, the width of the doorways is measured, which is subtracted from the total sum of the lengths of all sides, i.e. the perimeter. Now all that remains is to divide the resulting number by the length of one baseboard strip. By the way, if the result is fractional (and in most cases this is the case), then it is always rounded up.

It is also important to take into account possible errors and waste generation. For these “needs”, about 5-10% of the result is added to the resulting number. This will be the final amount of plinth required to decorate a particular room. To calculate the baseboard for the entire apartment, all measurements and calculations should be made room by room, i.e. in each room separately.

Recommendations for choosing skirting boards and related fittings

Choosing a flexible plinth is no different from choosing a regular plinth. It is important to consider several key points.

Installation of flexible PVC skirting board

After all the necessary calculations have been made, you can go to the store for skirting boards and, when you come home, get to work.

However, purchasing a profile is not all that needs to be done, because to install a flexible skirting board you may need the following elements and tools:

• plugs, corners (external and internal) for plinths, connectors;
• stationery or simple sharp knife;
• roulette;
• pencil;
• screwdriver;
• self-tapping screws;
• brush, spatula;
• glue for baseboards.

On a note! It is not necessary to purchase all of the above items, with the possible exception of components. In general, the choice and need for purchase will be determined by the choice of installation method for the baseboard.

There are three installation methods:

• using clips, which are fixed with self-tapping screws to the wall at a distance of about 3-5 cm from each other. The plinth is simply put on them. The method is used only on smooth walls;
• using dowels when the plinth is attached in the area of ​​the cable channel, and the fasteners are later covered with an external decorative strip;
• with glue. Experts recommend additionally screwing the baseboard with self-tapping screws for reliability. At the same time, even components are stuck to the glue.

Installation of flexible PVC plinth occurs as follows.

Step 1. The plinth is applied to the wall as it will stand. A mark is made with a pencil on the surface of the wall indicating its height.

A mark is made with a pencil

Step 2. Markings are applied to the entire wall, marking the upper border of the plinth.

Step 3. A special adhesive solution is applied to the wall surface using a small spatula (no wider than the height of the baseboard).

Step 4. The adhesive solution is also applied to the back surface of the baseboard.

Step 5. The plinth is carefully glued to the wall along the previously marked upper border. During installation, the element is pressed well by hand. The joint between the wall and the floor is worked out with a metal spatula.

Step 6. Special attention worthy inner corners. The first step is to soften the baseboard using a hair dryer.

Step 8 To avoid an unsightly protrusion in the corner, a neat cut is made on the protruding part of the plinth at an angle of 45 degrees.

Step 9 The halves of the “ledge” are laid neatly on top of each other. The excess is cut off with a knife.

Step 10 The outer corner should also be designed correctly. The baseboard is heated again by the hairdryer. Next, the material is carefully folded onto another wall. The joint is worked out with a spatula.

Installation subtleties

If PVC installation or polyurethane baseboard is done using a mounting strip or clips, then the fastening elements are simply fixed with screws and dowels at the same height along the wall. The baseboard is heated in water and then simply snaps onto the fasteners. When the material cools, the baseboard will become denser. It is advisable to start all work from the corner part of the room.

If installation is carried out using glue, then you cannot save on the adhesive composition. You should choose the highest quality solution. And, by the way, it is not applied to the floor surface, especially if laminate or parquet is laid.

Advice! Some additionally fix the baseboard not with self-tapping screws, but with furniture nails that do not have heads. However, it is necessary to treat the places where they are clogged with sealant.

Interestingly, on surfaces that are not overly curved, you can also use a regular polymer skirting board. You can see how to bend it in the video below.

Video - How to bend a regular baseboard

Flexible plinth is a real salvation for apartments with an unusual layout. It will make the repair neat and complete. And all thanks to the fact that the plinth bends perfectly. Not a single (even the highest quality) polymer plinth can ever be bent on its own the way a flexible plinth can be bent. And this is the main advantage.

When conducting repair work From time to time it becomes necessary to use a floor plinth to go around a curved section of a wall, a podium, a column, or to install a profile in a bay window. For such work, a flexible plinth is used, which allows for high-quality installation. On the market building materials Flexible skirting boards made of polyurethane, polyvinyl chloride (plastic), and cork are presented. Which one should you choose?

Plastic flexible skirting board

Most popular look floor plinth- plastic. This is determined by its versatility and affordable cost.

Dimensions of plastic plinth

The length of a standard plastic profile is 2.5 meters - it can be transported in transport and is convenient to work with. The cross-section of the profiles is different, it usually varies between 15-22 mm. The height of a narrow product starts from 30 mm, a wide plinth can reach 100 and even 150 mm.

The most common size is 50-60 mm with a cross section of 20 mm. A profile of this size can be used in most standard apartments.

Important! There is a rule according to which products with a height of up to 70 mm are recommended for use in rooms with a ceiling height of up to 2.5-2.6 m. For ceilings with a height of 3 meters, the profile should be in the range of 70-90 mm. A plinth with a height of 100 millimeters or more is optimal for very high rooms with ceilings higher than 3 meters. This rule is considered quite universal, but it is necessary to take into account the interior design of the room and the size of the decorative elements already used.

What is the difference between a flexible plastic skirting board?

Peculiarities:

• Flexibility of the planks, ease of installation and low weight. This profile can be pressed tightly against the surface of almost any wall.
• Enough high strength and durability.
• Moisture resistance.
• Resistance to ultraviolet radiation - plastic plinth does not lose its color in sunlight.
• Flexible plastic profile retains its properties at relatively low and high temperatures, but it cannot be used outside the home.
• Very important feature- it is non-toxic and fireproof.
• Flexible plastic skirting board is ready for use without pre-treatment.
• Variety of surface patterns and color solutions. Plastic products can imitate cork, natural wood, ceramics, metal.

• A flexible plastic profile with a cable channel makes it possible to covertly lay any number of wires and cables, and subsequently provide simple and convenient access to them during operation.
• Flexible plinth does not require special care.

Flexible profile design with cable duct

In the main part of the product there is a cable channel into which the wires are laid. There is enough space even for thick antenna cables. Before laying the wires, this part is attached to the wall, and after laying it is covered with a decorative panel. You can replace or remove unnecessary wires very simply - remove the top panel, replace, then install decorative panel into place and click into place.

Advice. Consult with specialists about the size of the cable channel you will need. You need to choose a model with a cable channel of sufficient size.

Installation of flexible plastic skirting board

The flexible profile can be installed using self-tapping screws, hidden mounting clips or glue. Installation with self-tapping screws and clips is usually used.

Accessories (components) for installation

Before installation, you must purchase the required number of elements that will be required during installation. These are external and internal corners, right and left side caps (they are always sold in pairs) and connecting elements for joining two planks. Make calculations of internal and external corners in the room, the number of plugs (they are installed in places where the baseboard fits the doorway and elements that would make direct installation impossible. Connecting elements are also easy to count. Buy these elements in the color of the product and with a small margin.

Remember that the profile in the corners is cut flush with the wall and inserted into the corners.

To work you need to prepare:

• A hacksaw or knife.
• Screwdriver or screwdriver.
• Hammer.
• Tape measure and pencil.

Important! Before installing the profile, check the color of each strip, and install strips of a darker shade opposite the window. So sunlight will make the difference in shades unnoticeable.

Installation methods:

• To install on hidden clips, first, clips are mounted along the walls in increments of 300-500 mm, fixing them to the walls with self-tapping screws. Avoid distortions during installation! The flexible plinth is placed on the mounted clips with light finger pressure until it clicks. This method is used for smooth walls, because the curvature of the surface will make installation very difficult.

• The easiest way to install a flexible plastic skirting board. Installation begins from the corner of the room, markings are made for dowels in increments of 300-500 mm and drilled in these places through holes in the main part of the profile (directly in the cable channel). Plastic dowels are installed in the wall and the profile is fixed with self-tapping screws. They will be covered with a decorative panel.

• You can attach a flexible plinth with a cable duct using glue, but experts recommend using the fastening method with self-tapping screws for reliability. When removing the decorative panel to access the wires, it is easy to damage the reliability of the adhesive connection. It is better to glue the connecting elements, because when cleaning the room they can be knocked off with a vacuum cleaner or mop.

Floor flexible plinth made of polyurethane

Flexible polyurethane profile (Flex) - decorative element to complete the registration flooring, allowing you to hide uneven areas where walls and floors meet, and also to lay wires unnoticed. Flexible products made from polyurethane repeat the line of standard products in size and shape, and differ from them in the composition of the material - for their production, rubber is added to polyurethane, which allows the product to bend along a radius of 0.5 m.

Flexible profile dimensions

The standard length of a flexible polyurethane profile is 2 m, but there are products on the market up to 2.5 m long. The cross-section is usually 20-25 mm, the height can reach up to 150 mm. A number of companies offer profiles with a height of 250 mm.

Properties

The characteristics of polyurethane depend on the polymers it contains. However, a profile made from this material is distinguished by:

Relatively light weight.

Product flexibility and ease of installation.

High strength.

No restrictions on installation in children's rooms and bedrooms.

Easy to care for.

Possibility of painting in any desired color.

Advice. For painting it is recommended to use acrylic paints in aerosol cans. Painting is carried out no earlier than 24 hours after installation of the profile. When painting, the junctions with the walls and flooring are sealed with masking tape.

Installation Features

Work begins from the corner of the room. In the corners, the profiles are cut at 45°, for which a miter box is used. Before installation, be sure to check the accuracy of the joining of the cut pieces of plinth.

Other tools you will need are a square, a tape measure, a fine-tooth hacksaw, a caulking gun and a pencil. You can sometimes use self-tapping screws to fix the flexible profile, then these places will need to be treated with sealant.

Installation will be facilitated by the flexibility of the plinth, which will fit snugly even on uneven walls. The wires are laid in special grooves of a flexible profile (cable channels).

You need to choose high-quality glue. Many manufacturers of flexible polyurethane skirting boards also produce adhesive putty for it, which is packaged in cartridges. It will be optimal solution. Liquid nails, synthetic adhesives such as “Titanium”, and styrofoam glue are also suitable.

Glue is applied using a gun to back side flexible plinth in two or three continuous strips so that when pressed the glue fills the entire back side of the profile. When the profile is installed, glue is also applied to the joint on one side.

The product is pressed against the wall surface, removed and the glue is allowed to dry a little. Then they press it again with force and hold it in this position for some time, following the manufacturer’s instructions. Excess glue must be removed immediately with a rag or sponge. If necessary, glue is added until it begins to protrude when pressed.

Advice. Additionally, you can secure it using furniture nails. They do not have a cap, but these places should still be treated with sealant.

It should be remembered that the flexible profile must be glued only to the wall surface. Under no circumstances should you glue the baseboard to the laminate.

Conclusion

A flexible polyurethane plinth for the floor allows you to design radial and curved junctions of the floor covering to the walls, as well as solve many other important practical problems. Right choice This is not as easy to do as it first seems - you need to choose a profile that is suitable in size, texture, shape, color, and even with a cable channel of the appropriate size. But installing it won’t be particularly difficult if you follow simple rules.

More modern renovation departs from standards. Simple urban style is being replaced by more elegant and flexible ones. design solutions. Straight lines are replaced by curvilinear, smooth, rounded shapes, so there is a need for new technologies for interior decoration.

Facing materials can be very different, but it is difficult to imagine a renovated space without skirting boards; this finishing element is, without a doubt, indispensable in any interior. In the article we will tell you what a flexible floor and ceiling plinth is, and how to bend a plinth from different materials with your own hands.

Flexible ceiling plinth allows you to trim complex rounded shapes

Possibilities

It should be noted that the finishing materials market quickly responds to the needs of modern renovation. Now on sale different models bendable skirting boards, and if polystyrene strips are very fragile and almost do not bend, then the polyurethane profile with the addition of rubber is very flexible and ductile.

The best solution for finishing a complex curved area with many curves is soft, flexible skirting boards. This is usually vinyl or flexible polyurethane baseboard with a high percentage of rubber. The profile is very elastic and is sold in rolls; it is easy for them to go around both external and internal radius corners.

For example, flexible floor plinths are used in rooms with complex shapes, for arches, columns, rounded podiums, etc., and flexible ceiling plinths are used for finishing curved plasterboard structures or tension systems.

In addition to flexible models, a wide range of curved radius plinths with different diameters and from different materials are available for sale. As a rule, these are wooden and polyurethane segments on round corner or a column.

Flexible, semicircular self-adhesive vinyl plinth, easy to cut and bend to any radius

How to bend a plinth with your own hands

Despite the huge selection of soft, flexible and radius profiles, it is not always advisable to use them. As a rule, sometimes it is easier to bend a regular bendable baseboard. Plastic, cork, MDF and wooden skirting boards can be easily bent into smooth semicircular bends.

But in order to bend them along the radius of a small circle, you need to know the secrets of technology. Because physicochemical characteristics materials vary significantly, hence the approach to the process of how to round a plinth is very different.

Flexible polyurethane floor plinth allows you to easily bend around semicircular surfaces with a flat radius

Thus, a flexible floor plinth made of composite plastic can be easily bent into a semicircle using a household hair dryer with a power of 1 kW or more. It is enough to heat the profile in the right place and carefully round it to the shape of a semicircular wall. Note that a plastic bendable composite plinth with wood chip filling is difficult to distinguish from a veneered profile, so it is ideal for interiors with wood floors. natural wood.

To bend a plastic plinth with a cable channel onto a flat semicircular surface, you will need to cut off all the stiffeners, leaving only the decorative layer intact. Next, to make the molding flexible, it is heated construction hairdryer, and carefully bends at the installation site; during the process, grab the whip so that it “remembers” the required round shape.

Cork flexible floor plinth can be easily bent, but for small round shapes will have to go around with steam

If the profile is not flexible enough and you need to go around semicircular shapes with plinths made of wood, foam plastic, MDF, and some polyurethane models, then in this case it is necessary to format the fillet. To do this, transverse cuts are made from the wrong side, almost in profile depth, leaving only front layer 3-5 mm. It is better to make the slits with a hacksaw for metal with a thick blade, every 5-7 mm.

Formatting flexible PVC profile

When formatting the profile does not help, in order to go around the surface, you will have to use radical way. The non-flexible plinth is cut into small pieces, and each piece is individually adjusted to fit a round wall. But this method of manufacturing a semicircular shape requires serious skills, so it is very difficult to install such a rounded segment yourself.

As a rule, joining several individual parts is used if the interior includes a wide polystyrene ceiling plinth for a round wall. After finishing, the bent area is carefully puttied, and the plinth is painted in several layers, so the joints become invisible.

The photo shows how to finish a rounded surface with a non-flexible whip

How to make a bent wood segment

Solid wood baseboards are usually bent using steam. It is necessary to measure the round area and cut it out right size profile with a margin of 50-75 mm on each side. Next, a large pan of water is placed on the stove, brought to a boil, when the steam becomes intense, the cut baseboard is placed on top.

Depending on the type of wood, pine, for example, is more flexible, you need to steam the profile for 30-60 minutes, saying the words: “I’m twisting and turning, I want to bend the profile!” When the profile is well saturated with steam, it is applied to the place of fixation and bent along the required radius. In order for the tree to take the desired shape, it should be fixed in several places. But this method can easily lead to deformation of the baseboard after drying.

Bent wooden profile in the interior

In order to correctly bend a wooden whip in a semicircle, professionals make a special pattern, then make a template using it. They fix the steamed whip on it with clamps, metal point and tape, so the bent semicircular shape turns out to be more even and accurate. Before making the plinth into a semicircle, it is recommended to soak the underside with PVA glue so that after drying the bent segment will better retain its semicircular shape.

We have also prepared a video for you on how to bend a plastic plinth with your own hands in a semicircle. We hope our tips will help you with your repairs, remember, the deposit beautiful interior- neatness and creativity to the process.

Modern renovations are increasingly moving away from standards. Simple urban style is being replaced by more elegant and flexible design solutions. Straight lines are replaced by curvilinear, smooth, rounded shapes, so there is a need for new technologies for interior decoration.

Facing materials can be very different, but it is difficult to imagine a renovated space without skirting boards; this finishing element is, without a doubt, indispensable in any interior. In the article we will tell you what flexible and is, and how to bend a plinth from different materials with your own hands.

Flexible ceiling plinth allows you to trim complex rounded shapes

Possibilities

It should be noted that the finishing materials market quickly responds to the needs of modern renovation. Now there are different models of bendable skirting boards on sale, and if polystyrene strips are very fragile and almost do not bend, then with the addition of rubber they are very flexible and ductile.

The best solution for finishing a complex curved area with many curves is soft, flexible skirting boards. This is usually vinyl or flexible polyurethane baseboard with a high percentage of rubber. The profile is very elastic and is sold in rolls; it is easy for them to go around both external and internal radius corners.

For example, flexible ones are used in rooms with complex shapes, for arches, columns, rounded podiums, etc., and flexible ceiling plinths are used for finishing curved structures made of plasterboard or tension systems.

In addition to flexible models, a wide range of curved radius plinths with different diameters and from different materials are available for sale. As a rule, these are polyurethane segments for a round corner or column.

Flexible, semicircular self-adhesive vinyl plinth, easy to cut and bend to any radius

How to bend a plinth with your own hands

Despite the huge selection of soft, flexible and radius profiles, it is not always advisable to use them. As a rule, sometimes it is easier to bend a regular bendable baseboard. , cork, MDF and wooden skirting boards can be easily bent into smooth semicircular bends.

But in order to bend them along the radius of a small circle, you need to know the secrets of technology. Since the physicochemical properties of materials vary significantly, hence the approach to the process of how to round a plinth is very different.

Flexible polyurethane floor plinth allows you to easily bend around semicircular surfaces with a flat radius

Thus, a flexible floor plinth made of composite plastic can be easily bent into a semicircle using a household hair dryer with a power of 1 kW or more. It is enough to heat the profile in the right place and carefully round it to the shape of a semicircular wall. Note that a plastic bendable composite plinth with wood chip filling is difficult to distinguish from a veneer profile, so it is ideal for interiors with natural wood floors.

To bend plastic onto a flat semicircular surface, you will need to cut off all the stiffeners, leaving only the decorative layer intact. Next, to make the molding flexible, it is heated with a hair dryer and carefully bent at the installation site; during the process, grab a whip so that it “remembers” the required round shape.

Cork flexible floor plinth can be easily bent, but small round shapes will have to be bent using steam

If the profile is not flexible enough and you need to go around semicircular shapes with plinths made of wood, foam plastic, MDF, and some polyurethane models, then in this case it is necessary to format the fillet. To do this, transverse cuts are made on the reverse side, almost to the depth of the profile, leaving only the front layer of 3-5 mm untouched. It is better to make the slits with a hacksaw for metal with a thick blade, every 5-7 mm.

Formatting flexible PVC profile

When formatting the profile does not help, in order to bend the surface, you will have to use a radical method. The non-flexible plinth is cut into small pieces, and each piece is individually adjusted to fit a round wall. But this method of manufacturing a semicircular shape requires serious skills, so it is very difficult to install such a rounded segment yourself.

As a rule, joining several separate parts is used if the interior provides a wide polystyrene plinth for a round wall. After finishing, the bent area is carefully puttied, and the plinth is painted in several layers, so the joints become invisible.

The photo shows how to finish a rounded surface with a non-flexible whip

How to make a bent wood segment

Solid wood is usually bent using steam. It is necessary to measure the round area and cut out the required profile size with a margin of 50-75 mm on each side. Next, place a large pan of water on the stove, bring it to a boil, when the steam becomes intense, place the cut baseboard on top.

Depending on the type of wood, pine, for example, is more flexible, you need to steam the profile for 30-60 minutes, saying the words: “I’m twisting and turning, I want to bend the profile!” When the profile is well saturated with steam, it is applied to the place of fixation and bent along the required radius. In order for the tree to take the desired shape, it should be fixed in several places. But this method can easily lead to deformation of the baseboard after drying.

Bent wooden profile in the interior

In order to correctly bend a wooden whip in a semicircle, professionals make a special pattern, then make a template using it. They fix the steamed whip on it with clamps, metal point and tape, so the bent semicircular shape turns out to be more even and accurate. Before making the plinth into a semicircle, it is recommended to soak the underside with PVA glue so that after drying the bent segment will better retain its semicircular shape.

We have also prepared a video for you on how to bend it with your own hands in a semicircle. We hope our tips will help you with your renovation; remember, the key to a beautiful interior is accuracy and a creative approach to the process.

Modern renovations are increasingly moving away from standards. Simple urban style is being replaced by more elegant and flexible design solutions. Straight lines are replaced by curvilinear, smooth, rounded shapes, so there is a need for new technologies for interior decoration.

Facing materials can be very different, but it is difficult to imagine a renovated space without skirting boards; this finishing element is, without a doubt, indispensable in any interior. In the article we will tell you what flexible and, and how to bend a plinth from different materials with your own hands.

Flexible ceiling plinth allows you to trim complex rounded shapes

Possibilities

• We heat up the molding so that the bridges remaining in the cuts become flexible. We carry out heating carefully, with reverse side molding. We carefully ensure that outer side did not deform from high temperature.
• When the baguette warms up well and becomes flexible, it must be carefully but quickly bent. The plastic cools down quite quickly, so you shouldn’t hesitate at this stage.

Bendable baseboard. This effect is achieved by heating the plastic

Making semicircular wooden baguettes

But here everything is more complicated. You cannot make cuts, but the method we propose to use will allow you to bend the profile quite a bit. However, if you only need to adjust the baseboard to an uneven wall, then this option is quite suitable.

First we prepare spacers for the wooden profile. To do this, take a board and draw a semicircle of the future bend on it. Now on both sides of the line we screw or nail the spacers themselves. For example, long nails can serve as them. You can also come up with your own version. The spacers repeat the future semicircle of the profile, and are arranged in a checkerboard pattern, as in the diagram below.

Spacers required to make the baseboard semicircular

Now we need to steam the baguette to make the plinth for the ceiling or floor flexible and give it a semicircular shape. The easiest way is to boil a pot of water on the stove and hold the profile over it. How long it takes for the molding to become flexible depends on the type of wood. This moment can be determined by touch; when you try to bend the profile, it will begin to give in.

After the wood has steamed and become flexible, we remove it from the steam and place it in the semicircle of spacers that we prepared earlier. Here the profile should remain until the wood dries completely. Ideally, we steam the planks in the evening and leave them bent in a semicircle until the morning. After drying, the bent profile can be installed in the intended place.

We make from wooden profile ceiling plinth, flexible

Buying ready-made moldings

On sale you can find ready-made flexible skirting boards for floors and ceilings. They are made from different materials:

• , flexible.
• Soft molding and PVC plinth tape.
• Flexible floor plinth made of cork, semicircular, bent.

Flexible polyurethane plinth has optimal combination price – quality, used quite often. Skirting tape is relatively inexpensive, but it is difficult to install and not every type of adhesive is suitable for it. It is most often used for the bathroom. Flexible floor plinth made of cork is the most expensive of these three types, but its advantage is the naturalness of the material and excellent appearance.

Flexible plinth, floor, cork

The radius bent plinth is made from natural wood. It is almost impossible to buy such moldings ready-made, since they are made according to the radius of a certain bend of a wall or column. Therefore, this decor is purchased, as a rule, to order, and it cannot be classified as cheap. However, bent semicircular moldings made of wood undoubtedly outperform plastic in appearance, so all the time and financial costs will be justified.