What glue to use to glue rubber boots. How to repair rubber boots at home

A person feels extremely uncomfortable in shoes with holes, even if the puncture is not visible from the outside. This, of course, is an excellent reason to buy new boots, but this opportunity is not always available. But even if there is one, don’t rush to throw away the spoiled pair. It is very possible that she will still serve. How to seal boots? Read about it in our article.

What kind of shoes were torn?

It's no secret that repairing rubber boots differs from repairing leather boots, but it has some similarities with sealing shoes made of PVC or waterproof material called “EVA”. Leather shoes can sometimes be sewn up, and this is better than putting a patch on glue, but with rubber shoes you can’t do anything like that - glue, just glue, and no unnecessary punctures!

The repair method may also depend on which part of the boot the hole is found in:

in the sole;
the upper has peeled off from the sole;
on the smooth part of the top;
on the boot;
in the seams.

Are there any prospects?

The first option is the hardest. The sole rubs and experiences serious mechanical stress, so the connection must be strong. Most often, a hole appears because a person stepped on a nail or something similar.

Important! It is possible to seal the hole, but it is unlikely that it will be possible to do it in such a way that the boots will last for several more seasons. At worst, they will last a month.

A peeling top is also a bad option. There is less friction and mechanical loads too, but they are enough that after a couple of times the recently repaired shoes will fall apart again. It’s better if there is even the slightest opportunity to sew the top to the sole at least in this place.

Lung damage

A hole in the smooth part of the upper and boot is usually repaired quite easily and the patch takes a long time. In this case, it is very important to choose the right glue. This is especially true if the hole is at the bottom, which is exposed to water and dirt.
A hole in the boot appears if you bump into rebar sticking out of the ground or run into a nail that has come out of the wall. In this case, there are almost no mechanical loads on the gluing site, so you can also think about aesthetics - make a patch that will not be very noticeable (or vice versa - turn it into a decorative element).
A ripped seam can also be repaired quite simply. This defect is naturally characteristic of leather shoes or leatherette boots. The seam will hold up better than gluing.

We repair leather boots

It is better to take expensive dress shoes to a workshop. True, repairs are sometimes more expensive than a new pair, so each case must be approached individually. But applying a patch to the upper part can also be considered minor repairs, so it will be relatively inexpensive.

Choosing glue

The first thought that comes to mind when you need to glue a small, but important detail- use superglue. In this case, it is better to discard this idea immediately. The glue, of course, will dry quickly, but it has a bad effect on the structure of the leather or leatherette and the gluing area becomes fragile.

Important! If you try to walk in boots repaired in this way, the hole will simply grow larger and its edges will become brittle.

Professional adhesives are suitable for you:

“Dismakol”;
“Nairit.”

These are the compounds used by professional shoemakers. They are not always on sale, and the best place to look for them is in stores that sell leather scraps and other arts and crafts supplies. If there is no such specialized store nearby, “Moment Marathon” or another elastic composition will help you out.

Important! Before starting work, be sure to read the instructions and act strictly in accordance with them.

If the seam on the boot comes apart

In this case, you won't need glue at all. You need:

thick nylon threads;
needle;
awl;
tablet;
blade.

Important! An awl and a board are needed just in case the needle does not fit into the existing holes.

Sew up:

There is no need to make additional holes; they reduce the strength of the product.
Use a blade to carefully support the lining.
Thread the thread through the needle, fold it in half and make a knot at the end.
Insert the needle from the wrong side into the outer hole.
Pull the thread to the right side.
Insert the needle into the outermost hole on the opposite side of the seam.
Stretch the thread so that the stitch on the outside becomes flat, but do not pull too hard - the nylon thread can tear the leather.
Insert the needle from the wrong side into the second hole on the side from which you started sewing.
Make a second stitch - into the second hole on the opposite side.
Having finished the seam, bring the thread to the wrong side and secure with any in a convenient way(you can even melt it).

Gluing the seam

Many modern models They look like they are sewn, but in fact the seams on them are purely decorative, and the strength is ensured by gluing. In this case, stitching the hole is useless. It's better to do this:

Cut 2 strips of leather 1 cm longer than the hole.
Glue them to each side of the seam, leaving a 0.5 cm seam allowance.
Glue the allowances together or sew them with nylon threads.

The top tore in a smooth place

The most unpleasant option is that any patch glued to the outside will be perfectly visible. There are two options:

stick the patch on the inside;
stick on the outside, making an applique,

Important! In the second case, you will have to repair the other boot, even if it is completely intact. Therefore, you need twice as much leather for a patch.

Option 1

A piece of leather, pasted over from the inside, comes into contact with the leg and may begin to rub. Therefore, the patch should be made of thin leather or even waterproof fabric:

raincoats;
bologna;
avisenta.

But the size of the flap can be anything. To seal your boots, proceed as follows:

If possible, turn the boot inside out.
Cut the patch so that it completely covers the puncture and there is still allowance on all sides.
Apply glue around the hole at a distance of 3-5 mm from the edge.
Attach the patch from the wrong side.
Butt the edges of the hole together and press.
Turn the boot right side out.
Carefully coat the edges that are not glued with glue (you can use a cotton swab).
Press the edges well.
Remove excess glue immediately.

Option 2

It is much simpler than the previous one, because all work is done on the front side:

Cut out 2 identical leather parts - matching or contrasting.
Lubricate them with glue.
Cover the hole with one piece, and symmetrically glue the other to the second boot.

Torn out sole

In this case, you won't get away with a tube of glue and a small piece of leather. You will also need:

skin;
acetone or white spirit;
wire or elastic bandage.

Before you seal your boots at home, get them in order. Shoes must be clean and dry.

Clean the tear area of any old glue.
Go over it with fine sandpaper.
Degrease surfaces with white spirit or acetone.
Apply glue according to instructions.
Press the parts tightly together - they can be tied with wire or bandaged with an elastic bandage.
Wait for the glue to set - this usually takes a day.

Hole in the sole

If you step on a thick nail, your shoes will also have to be sealed. You will need:

epoxy resin;
patch material;
scissors or sharp knife.

It is best to fill the break area. Epoxy is suitable for both leather and plastic soles:

We apply the composition according to the instructions on the package.
Fill the hole.
Let it harden.
Cover the puncture site with a patch or insole on top.

How to care for leather boots?

No one is immune from some damage - anyone, even the most careful person, can run into a piece of reinforcement or a nail. But sometimes boots crack and tear simply from improper care:

After you come in from the street, put your shoes in order - clean them from dirt and dry them.
Clean leather boots regularly with cream.
Lubricate your shoes with castor oil periodically.

Important! If you need to place boots or shoes on long-term storage, do not forget to stuff them with napkins or newsprint. Napkins will also help you out when drying - by filling the toes of your boots with them, you can be sure that the shoes will not lose their shape.

How to fix rubber boots?

Many people think that repairing rubber boots with their own hands is impossible; it is better to immediately throw them away and buy new ones. This is not entirely true. Your shoes will last you a very long time if you carefully seal them, and before you get down to business, follow a few simple steps:

Wash your boots thoroughly.
Dry them well.

What to make the patch from?

A needlewoman will always have a scrap of leather in her house, but where can she get a piece of rubber? Nothing complicated. They will help you out:

old bicycle tire;
old rubber boots;
hammer;
a piece of rubberized fabric.

You also need rubber glue (you can also use universal shoe glue if you can get it), as well as fine sandpaper or a file.

Important! Rubber gloves or old rubber toys will not work for you: the former are too thin, and the latter are made of a different grade that delaminates.

Let's start the renovation

The rubber patch can be easily cut sharp scissors. She must be more hole, but not by much. Unlike leather shoes, which sometimes come apart simply because the threads have rotted, a hole in rubber boots most often appears from mechanical damage. Therefore, you can easily encounter a situation where a piece is simply torn out and the edges cannot be aligned.

It is better to glue on the front side, proceeding in this way:

Cut out the patch.
Treat the underside of the workpiece with sandpaper or a file - this is necessary so that the surface becomes rough, then it will hold better.
Wipe the surfaces to be glued with acetone or white spirit.
Lubricate both surfaces with glue according to the instructions.
Press the patch firmly against the boot.
Tap the gluing area with a hammer.
When everything is dry, go over the seams sandpaper to make the gluing area uniform and mask the patch.

How to seal PVC boots at home?

In everyday life, all boots made of waterproof materials are usually called rubber. However, this is not the case. To make such shoes, PVC, polyurethane, and EVA are used.

The repair technology in all cases will be the same as when working with rubber, but a different glue is needed. It should indicate what material it is intended for. And, of course, when buying boots, it is very useful to remember what they are made of - there may not be markings on such products, but there is usually one on the price tag in the store.

Repair without patch

Waterproof shoes can be repaired without a patch:

Turn the edges of the hole outward.
Lubricate them well with glue.
Press the edges together so that there is no gap between them.

We use a repair kit

If you have rubber boots in which you go hunting or fishing, buy a regular bicycle repair kit, with its help you can repair your shoes in field conditions. The kit contains ready-made patches on special protective films. In addition, there you will find glue (designed specifically for this material) and a piece of sandpaper the desired faction. The boot is sealed in the same way as with a self-cut piece of rubber, but there is no need to degrease the patch, because it has a protective film on it that needs to be removed.

Important! The hole in the sole is repaired in the same way as in the boot.

Women's rubber boots

Rubber boots are not only worn by hunters and fishermen. They can also be seen on the capital's fashionistas. However, stylish boots tear no less often than those worn by lovers of extreme recreation.

But in this case, it is important that the gluing area is not noticeable, and that the boots retain their attractive appearance. Silicone sealant will help you out:

Degrease the gluing area with acetone or another compound.
Apply sealant to the edges of the hole.
Press them tightly together.

Curing

Most reliable way repair of rubber shoes. But it requires determination, certain skills and special equipment - a vulcanizer:

Before gluing the flap, you need to soak it in gasoline for a little while.
Apply a patch to the hole.
Press the entire structure with a press.
Turn on the vulcanizer and let it run for about half an hour.
Turn off the vulcanizer.
Let it cool completely.
Remove the press.

Two words about leaving

Rubber boots are an unpretentious product. However, it also needs care:

After you take off your boots, wash and dry them well.
Please pay Special attention on the lining - if it is not dried well enough, it will begin to rot and quickly tear.
From time to time, wipe rubber products with a cloth soaked in glycerin.

In this article we told you about all the ways to repair boots from the most different materials. Now, we hope that in any situation you can find correct solution and repair your shoes using improvised means.

A small shard of glass, a nail or an ordinary push pin lying under the table is enough to render rubber boots completely unusable. The unpleasant surprise is aggravated by the fact that shoe repair shops Rubber boots are not accepted. Don't buy new boots. Let's try to figure out how to seal rubber boots with our own hands.

It is worth noting that rubber boots, like EVA boots, are not so easy to seal. Regular shoe glue won't take them, but superglue will ruin them.. You need special glue.

Angler's method

You can look for special rubber glue in hunting and fishing stores. Quantity unsuccessful attempts will be reduced to a minimum if you know what your rubber boots are made of. To repair products made from PVC, polyurethane or EVA, completely different adhesives are required. Ask the seller for the glue you need and follow the instructions on the package. As a rule, the technology is the same: sand, degrease, glue a patch.

How to seal boots made of EVA, because they are porous? If you purchased special glue for EVA, then you won’t even need a patch. Carefully turn out the edges of the hole and apply glue to the porous structure until it is absorbed. Then line up the edges and press. After repair, even the boot will look quite aesthetically pleasing.

Cyclist's way

A proven way to reliably seal rubber boots is a bicycle repair kit. It usually contains several patches on protective films, special glue and sandpaper. Rub the area where the patch is glued with sandpaper, an area slightly larger than the size of the patch. Then degrease it with acetone.

Remove the film from the patch and apply glue to the exposed surface, also cover the glued area on the boot with glue. After 5-10 minutes, when the glue has dried, press the patch firmly.

You can use repaired boots almost immediately, they will be completely sealed. One problem is that bicycle patches do not look very aesthetically pleasing, so they are only suitable for rubber country boots.

Motorist method

What to do if smart women's rubber boots need repair? Like EVA boots, they are best sealed without a patch. You can fill the hole in colored and transparent rubber boots with elastic adhesive sealant.

The adhesive sealant has proven itself well " crazy hands» brand "Done Deal". You can buy one in stores for car enthusiasts. For everything to work out as it should, do not neglect preparatory stages. After washing, dry the shoes thoroughly and degrease the hole with acetone. The quality of gluing depends on this.

Again, seal leather boots and rubber boots are needed different glue— keep in mind that all of the listed materials are not suitable for leather.

When the snow melts and the ground turns to mud, the dull autumn rains come and there are puddles everywhere, there are no better shoes than rubber boots. There are only times when you step on a piece of glass or get caught on a wire, and that’s all - a puncture or cut. They seem to be good boots, but they let water through. But we are not in a hurry to throw the thing away, we will try to repair it.

To repair rubber boots you will need: rubber glue (preferably Red sun or Moment), a grater or abrasive paper, scissors, raw rubber, some gasoline. First you need to find the puncture or cut site. If the damage is not visible, then you should tighten the boot top so that the air in it is compressed under pressure. Place the boot in a basin of water, and where the bubbles are, there will be a cut or puncture site. You can insert a pointed match into the puncture so that the place is not lost.

Boot repair can be done in two ways - hot and cold. Each of them has both its advantages and disadvantages. Let's look at both. For hot repairs you will need a vulcanizer. Repairing a boot using a vulcanizer requires some experience with it. You need to soak the raw rubber in gasoline (about 10 minutes), then put it on the hole and press it with a vulcanizing press. Turn on the vulcanizer for 25-35 minutes, then turn it off to allow it to cool to normal temperature, and then remove the press. In the end you will get high-quality repairs defect. Cold way more simple. Before repairing, thoroughly wash and dry your boots. This method requires the item to be clean. The damaged area must be thoroughly cleaned with abrasive paper. If the boot is torn, you can tighten the edges of the tear by stitching with thread, then proceed to the next step. You can make the patch yourself from rubber. You need to clean it evenly from the inside, and from the outside - the edges should be thinner. You can use ready-made patches from a wheel repair kit, and you can get glue from there.

Apply glue to the damaged area of the boot and to the patch. Let it dry for about ten minutes and apply the compound again, let it dry again for about twenty minutes and carefully, without touching the glue, apply the patch. Afterwards we put the boot with the patch under the press for two hours. You can press it with a table leg. When the patch is securely stuck, it needs to be treated with fine abrasive paper.

Rubber boots are footwear necessary not only for the country house, but also for the city. They protect from bad weather and dirt. But it has one drawback - any nail or piece of glass is enough to render the shoes unusable. It’s impossible to give such boots to a workshop, but it’s a shame to throw them away. Therefore, many people prefer to repair their favorite shoes themselves.

How to care for boots

Rubber shoes must be properly cared for. And then you won’t have to resort to them frequent repairs. After all, even high quality, which is guaranteed by the manufacturer, does not always mean the safety of the shoes.

Rubber boots need to be cleaned properly. They are best washed with a solution of glycerin and water. In this case, boots should be wiped with a soft cloth and dried often to prevent fungus from appearing. Wet rubber boots cannot be dried with a hair dryer or radiator. It is necessary that the shoes dry naturally.

In order for the repair of boots to be successful, and for the shoes to last for a very long time, you need to know the following:

Before repairing, rubber shoes must be very thoroughly cleaned, washed and dried.
The patch can be cut from a tire or old rubber boots.
It is better to carefully process the patch from the reverse side with sandpaper or a file to make the surface rough for better adhesion of the glue.
It is best to degrease the surface of shoes with acetone and solvent.
You need to choose a special glue, which must indicate, for example, “shoe” or “rubber”.
Before repairing rubber boots, be sure to read the instructions from the glue manufacturer in order to do everything correctly.
It is best to smear the patch and the gluing area special glue several times, after waiting until the first layer dries a little.
When gluing the surfaces, you need to press them very hard against each other or tap the gluing area with a hammer.
A patch on a boot can be easily masked using sandpaper.

Method 1. You can seal your boots with special glue. It can be purchased in stores for hunters and fishermen. But in order to acquire the right glue, you need to know what exactly the shoes are made of. The fact is that shoes made of EVA or polyurethane require different adhesive compounds.

Help purchase necessary glue the seller can give advice. Then everything is simple - you need to sand and degrease part of the boot and stick on a patch. If the shoes are made of porous material, then they can be glued without using a patch. The edges at the cut site just need to be turned out, generously coated with glue and pressed together.

Method 2. For this method you will need a regular bicycle repair kit. It contains patches on special protective films, sandpaper and, of course, glue. Clean the desired area on the shoe with sandpaper and thoroughly degrease. Next, after first removing the film from the patch, you need to apply glue to it and press the patch to the hole. You can use the shoes almost immediately, but it is better to wait at least 12 hours. The only drawback of this method is the unaesthetic appearance of the shoes after repair.

If the hole appears not on the boot, but on the sole, the gluing technology does not change. You just need to make the surface smooth and even, because usually the sole on such shoes is quite textured. This is possible using sharpening machine. And only then glue the patch to this place.

But it is important to know that such a patch will not last long, especially if the sole of the boots comes into contact with a rough and hard surface very often. Therefore, it is better to wear such boots, for example, when fishing. Well, if the sole breaks again, the gluing procedure will need to be repeated.

Method 3. In order to seal women's boots without using patches, etc., you need to purchase an adhesive sealant. This can be done at any car enthusiast store. First you need to degrease the gluing area, and then apply glue to the torn edges and press them together. If you do everything carefully, the boots will look like new.

Method 4. This method of repairing rubber shoes is also called the “hot” method. It is not complicated, but it requires certain skills and, most importantly, a vulcanizer. Rubber pre-soaked in gasoline is used as a patch. It is placed on the hole in the boot and clamped with a vulcanizer. The device needs to be turned on for 20–30 minutes, then turned off and cooled. Only after it has cooled can you remove the press.

Don't despair if your favorite rubber boots suddenly break. It is enough to put in a little effort and the repaired boots will be no different from new shoes. You can use taped boots a day after the patch was applied. But if you don’t have time to wait, then you can wear them in an hour.

Video: how to seal rubber boots with your own hands

Rubber shoes are incredibly popular in the off-season. And in gardens it is much more convenient to water and weed the beds, because no dirt or moisture is scary. At proper care and choosing the manufacturer, such shoes will last you more than one year.

How and with what to seal rubber boots?

However, no one is immune from damage to even thick rubber. We offer two simple and available methods, how to seal rubber boots.

Caring for rubber boots

So that such a nuisance does not take you by surprise, you should properly care for your rubber shoes. After all, even very good producers They will not be able to guarantee the safety of your boots if they are not properly cared for.

First of all, let's learn how to clean properly. To wash rubber shoes, just take warm water, soft cloth and just a little glycerin. Then appearance the product will last for a long time. Don't forget to ventilate your boots well to avoid the development of fungus.

After cleaning or use in very rainy weather, never place shoes on a radiator, dryer or use a hair dryer. Dry only in a warm, dry place or in a warm wind. If you purchased a model with a light or white sole, a regular school eraser will help make it look brand new again.

How to seal rubber boots - the classic method

Even if you take very good care of your rubber shoes, sooner or later they may deteriorate. In such a situation, the question quite logically arises: is it possible to seal the rubber boots, or will you have to go to the store for a new pair?

There is no need to panic, because it is quite possible to seal such a product. You don't even have to seek help for repairs. From the materials and tools used, you will need glue, solvent, and a patch (it is usually cut from old inner tubes from bicycles or strollers).

Shoes should be thoroughly washed and dried, as discussed in the rules for caring for rubber boots.
Cut the patch to size. In addition to bicycle tubes, old rubber boots are quite suitable.
Next, using a solvent, thoroughly degrease the surface of the shoe and the patch itself. Make sure that no pieces of cotton wool or threads from rags remain on the treated area.
To fix the patch we use Super Moment type rubber glue for rubber. If you wish, you can simply go to any nearest shoe repair shop and ask the master to sell you some special glue for a nominal fee.
First we apply glue to the shoes and the patch, let it sit for a while, then fix it. The exposure time is usually indicated on the tube.
To keep the patch as tight as possible, it is usually tapped a little with a hammer or something similar.

How to seal rubber boots - an alternative option

Sometimes the patch method is disappointing and you have to look for something else to seal your rubber boots with. If after a while you see that it was not possible to fill the hole, go to a sporting goods store. Many bicycle owners claim that a more reliable way to fix their rubber boots if they are torn is to use a bicycle tire repair kit.

Whatever method you choose, it is better to put on your boots after a day, when the glue has completely dried and set well.

How to wash sneakers in a washing machine?

No hand wash can compare with the quality of an automatic machine, and sneakers washed in a machine will surprise you with their perfect cleanliness. We will tell you in this article how to properly wash sneakers so as not to spoil your shoes.

How to disinfect shoes from fungus?

Foot fungus is a difficult to treat disease; it is much easier to prevent it, including disinfecting shoes. We will tell you how to do this correctly and what means to use in the article.

How to break in new shoes?

Sometimes it happens that, having brought home a pair of shoes from the store, we find that walking in them is quite difficult and uncomfortable. In this article we will tell you how you can break in your shoes in this case.

How to clean nubuck shoes?

Nubuck is a reliable, waterproof, but at the same time very difficult to care for material. We will tell you in this article how to properly clean nubuck shoes so that they do not lose their properties.

EVA stands for ethylene vinyl acetate and is an environmentally friendly, durable, lightweight, resilient and elastic material. It does not absorb moisture and odors, is easy to clean, in most cases it is used in the production of shoes and has the disadvantage that it is not resistant to sharp tools; such shoes will be punctured or even cut by a knot if the step is unsuccessful.

Therefore, repair is enough actual question for EVA products. Universal adhesives won't fit.

How to seal PVC or EVA rubber boots at home

Boots made from EVA can only be sealed with specialized material.

Characteristics of the adhesive composition

Sneakers, boots or winter fishing boots made of EVA material will be properly sealed only with the same material, i.e. EVA glue.

Properties:

waterproof;
does not spread;
is able to tightly connect gaps formed at the bend, as well as side and corner ones;
the repaired area remains almost invisible;
means for a long time adheres to the shoe, thanks to which the damaged area is protected from repeated damage;
the composition is consumed sparingly, since the manufacturer recommends applying it thin layer(otherwise the polymerization process becomes more difficult);
inexpensive, a 15 ml tube costs about 100-120 rubles;
Shelf life is 24 months (2 years).

How to use correctly

The method of working with EVA is practically no different from the usual one, you just need to take into account that it is impossible to glue PVC products with the product.

Instructions for use:

Clean the areas to be joined and degrease with acetone. You can do without degreasing, but in any case, the areas to be glued must be clean and dry.
Expand or compress the damaged area so that the porous surface of the ethylene vinyl acetate (usually inner side product) ended up outside. This is important because the glossy outer surface does not adhere.
Apply adhesive material to the porous area of the cut (tear) and leave for three to four minutes.
After this, bring the edges of the gap together and press them firmly together.
The final hardening of the product occurs after a day (24 hours).

In a similar way, you can repair, for example, Toptygin winter fishing boots. The manufacturer indicates how to use the glue correctly on the packaging of the composition. Follow the instructions and the cut will literally disappear from your shoes.