How to paint doors covered with film. How to paint a laminated interior door so that it becomes new and lasts a long time
Reviews from site visitors:
I'll tell you about my own experience painting chipboard And film facades in furniture production.
Painting chipboard
Chipboard was painted, but rarely when the project indicated that, for example, the outer side wall of the kitchen or the details of the portal had to be the same as the painted or patinated facades.
In this case, grinding was carried out chipboard surfaces paper of P220 grit or coarser to break up the top protective layer laminate on chipboard to a matte surface. Next, paint was applied, but more often they worked according to the scheme - sanding, one layer of primer, sanding, finishing. No adhesives were used.
Problems arose if the edge was poorly glued and after finishing the paint fell into places where the edge did not fit well, worse if it peeled off, but again this was due to poor performance of the gluing equipment, a violation of the gluing technology.
Painting facades covered with PVC film
We had to resort to the technology of painting film facades in order to simplify the technology of painting facades with complex internal milling.
What were the difficulties: the main ones were the labor intensity of grinding complex milled profiles and the risks of damaging the profile itself, which already required alteration of the facades.
In addition, it was necessary to apply sealing primer, sand it, apply base primer, sand, apply primer again, and sand again. In the case of film, the surface and profile of the MDF facade in PVC film were simply pre-grinded and finishing layers were applied.
It turns out that the technology was reduced to a minimum, well, sometimes they could apply primer to the film before painting, but sanding the primer in this case was much easier than sanding unlined MDF.
Important point Another thing in all this is how well the film is pasted on MDF facades. If the film peels off from the edge, if there are inclusions under the film, glue sagging, poor-quality milling, poor preparation of the facade surface before pressing, then we will get not the advantages, but the disadvantages of this technology.
Therefore, the technology of pressing facades into membrane vacuum press must be at a high level.
In addition, the film itself must be selected for the facades. Firstly, it should be white, and secondly, it will be better if it is intended just for painting, that is, without a protective top coating.
Film suppliers called this film primer. In principle, you can use just white film, but a trial application and an adhesion test are necessary.
Interestingly, no adhesive primers were applied to the film facades; it was enough to matt the film by sanding. But, in any case, experiments are always needed, and then mass application of the technology, otherwise primer may be needed to improve the adhesion of paint to film or chipboard. For such primers, contact your suppliers, they will help you select the necessary paints and varnishes.
03.09.2016 112157
Every theater begins with a hanger, and the interior of any room begins with a door, which sets the mood and makes a significant contribution to the atmosphere of the interior and is important element room zoning.
Many people underestimate the need for updating, focusing on the choice of wallpaper, flooring and furniture. As a result, an unpleasant contrast is created between a “brand new” room and one that has lost its appearance, old door. But this can be avoided if you paint it yourself. Given that correct selection paint and adherence to dyeing technology, the result will be excellent, which will allow you to create a holistic harmonious interior and save significant money at the same time.
Which paint to choose?
There is such a paint for interior doors:
- alkyd enamels;
- acrylic enamels;
- nitro paint.
The ideal choice for painting would be acrylic enamel, which dries quickly and does not emit unpleasant odor. After painting, it may be necessary to apply an additional layer of varnish to protect the canvas from moisture and to create a pleasant glossy effect.
Nitro paint creates a great, even finish and dries within minutes, but it also releases toxic substances into the air. Therefore, when using it, children, pregnant women and allergy sufferers are removed from the room where the painted interiors are located.
In addition, such paint is not suitable for painting a veneered door, since under its influence the veneer becomes covered with stains that are difficult to remove.
As for the shade of paint, you should choose it depending on color scheme interior and your own taste preferences. You can choose the color of interior doors in accordance with the shade of wallpaper, individual elements of room decor or flooring. A neutral and discreet option would be white. Light beige, brown of various shades, wood-like color are considered classics. Extravagant colors - red, green, blue and other sharp tones create an effect of tension and visually disturb the peace of the home.
Selection of paint depending on the material
When choosing paint, you should consider what material the door is made of.
Painting wood or chipboard can be done with any paint.
If the door is made of, painting it is somewhat more difficult, since it is difficult to maintain the structure of the veneer. Therefore, it is advisable to use a varnish of a suitable shade or paint with paints that contain varnish, although ordinary acrylic water-based paint is also suitable.
It's easy to renew a laminated surface. It creates excellent adhesion to any coloring composition.
Preparing for coloring
Before starting staining, remove. In the event that you only need to slightly update the paint layer, this is not necessary.
Painting doors in an apartment begins with preparing the workplace. The door removed from its hinges is laid horizontally on suitable supports at a height of at least 50 cm from the floor. Ordinary stools are successfully used as supports, on which boards the width of door leaf. The supports must be covered with a non-slip, lint-free thick fabric. The door is processed first on one side, then turned over to the other.
The first stage of work is removing the layer old paint. For convenience, all fittings (handles, hinges, etc.) are first removed, and a small amount of cotton wool or rags is placed in the holes.
To remove a layer of old paint, use a solvent, hard wire brush or sandpaper.
After removing the paint, level the surface of the interior door, fill the cracks with putty, and polish the surface grinder or fine-grained sandpaper and apply a layer of primer. The primer is prepared from the same paint that will later be used to paint the main background. To prepare it, the finished paint is diluted with a solvent in a ratio of 1:3. The resulting composition is used to prime the canvas in 1 layer. If necessary, after priming, it is putty again, partially or completely.
All of the above applies to interior doors made of wood. When preparing to paint doors made from other materials, there are some important points to keep in mind:
- from a veneer door it is enough to remove upper layer varnish If you only need to slightly update the gloss, then the paint is applied over the previous coating;
- Only the top layer of waxy dirt-repellent impregnation is removed from the laminate canvas;
- doors made of MDF and chipboard are prepared for painting in the same way as wooden doors.
Painting
When the remnants of the old paint have been removed from the door and its surface is prepared for the application of new paint, begin painting.
To paint wooden door in an apartment, it is most convenient to use a roller, and to work on small details and protrusions - a small brush. It is convenient to use a special spray gun to apply paint. This is especially true in the case of painting a door made of MDF.
Before applying the paint, it is recommended to carefully filter it: this will make the coating more dense and uniform.
Important! The door leaf is painted only in one direction! You cannot put layers of paint towards each other. During work, avoid direct contact with the door leaf. sun rays. The room must be protected from dust and midges, which, sticking to fresh paint, will ruin the job.
If you want to varnish the surface, be sure to wait until the paint layer has completely dried. This process takes a day for acrylic paints and two to three days for alkyd enamels.
Coloring ideas
You can limit yourself to a color that matches the interior of the room, but why not show your imagination and turn the interior door into interesting detail interior?
To give the door a more decorative look, it is recommended to use several techniques:
- using a stencil. In this case, the door is covered with a background layer of paint, after which, after drying, an even, neat pattern is applied using a stencil,
- use of several colors. In this case, you can create interesting patterns in the form of stripes, squares or rectangles. To create an even pattern, you will need a special masking tape, with the help of which areas of the required shape are highlighted on a dried layer of background paint.
- artistic painting. Such option will do only for those who have certain drawing skills. To create the painting, artistic acrylic paints and thin synthetic brushes are used. At the same time, fairy-tale scenes are suitable for the door to the nursery, and floral ornaments are suitable for the bedroom or living room,
- creating a textured surface. To add interest to doors decorative look It is recommended to use a special hard roller or brush, which is used to work through the layer of recently applied paint. In addition, special paints are sold that, after drying, create a textured surface.
With diligence, you will receive a real work of art.
As you can see, painting interior doors with your own hands is not that difficult. To achieve an excellent result, you need to be patient, take your time while working and use high-quality materials.
The apartment is a one-room apartment in KOPE '96. It’s tempting, of course, to increase the area of the bathroom, but just in case, I want to consult with experienced people. What problems might arise if the plumbing cabin is removed?
false mirror
Good afternoon. My problem is a crooked mirror in the bathroom. I noticed this point a long time ago, but I’m not at all ready to give up the mirror, because... it goes with the only cabinet that fits in my small bathroom. Interested in the reasons - why does it distort? and how to solve this issue? Here are the versions that I heard over the phone in St. Petersburg companies that deal with mirrors: 1. It is necessary to change the mirror itself. There are 2 options: they make a mirror for me, I glue it to the base (issue price is 1000) and they make a mirror for me and replace it on the base (3200). 2. Everything needs to be changed - I heard a version that any mirror will be distorted if it is glued to an uneven base. An uneven base is very plausible in my case, because... the entire set of furniture is Chinese for Russia (. I won’t change it - it’s simply unrealistic to find a cabinet for 55 that is not shabby. To change a mirror with a base - pick up or order something in a light color wooden frame- the issue price is from 1000 to infinity)... What to do? Has anyone encountered such a "problem"? For information - I have 2 identical curved mirrors - ...
hotel redevelopment
Dear tenants, I ask for help in resolving the following issue. This apartment it is supposed to be converted into a hotel for tourists (2-3 people, possibly with children), respectively, to be rented out as a hotel room. Therefore, the question is: is it possible to redevelop this apartment so that “everyone would be comfortable with the least amount of effort”? I wouldn’t really like to destroy the walls between the room and the entrance, although (according to preliminary forecasts) they are not load-bearing inside. Is it possible to do without moving the door? The apartment has a separate entrance, the door is basically removable. Thank you!
Please help me with the design of a living room in a two-room apartment
The room is 3m wide and 5.7m long. One wall is 5.7 load-bearing, the second is 3 m with a window not located in the middle. On one side 1m to the wall, on the other 0.5m (to the load-bearing). The two remaining walls are made of plasterboard. The doors are located along the length of the plasterboard wall at a distance of 1 m from the second plasterboard wall. Standard 800mm doors open into the room. In principle, they planned to put corner sofa with a long side without a roller for a 3m wall. There they hung wallpaper in a pattern (with rotation to fit the size of the sofa). They planned to put a 40" TV under the window in the corner where the walls are 1m thick. Wardrobes didn't plan here. I want something, but it seems like I can’t do it without expert advice. All I come across is a TV on the wall or on a nightstand on a long wall, but that doesn’t suit us. I would also like the color scheme of the furniture. The wallpaper is already hung, light beige. To suit the size of the sofa, the corner is covered with wallpaper with a pattern, complete with the main ones. Doors are light oak. The beige sofa is a tone darker than the wallpaper. Thank you in advance for your qualified advice.
03.09.2016 87477
Modern inexpensive ones mean comfort in the home. They fully support good noise and heat insulation, since they are solid, produced by pressing various waste lumber. Coloring gives them the proper look. Choosing paint and doing the work is more difficult than with solid wood. This is what we will talk about.
How to choose a coating for MDF canvas
The abbreviation MDF stands for finely dispersed fraction. That is, the canvas consists of shavings and wood fibers, pressed or glued together. There is no need to talk about environmental qualities - the chemical composition is present in large quantities, but the shortcoming is covered by good performance and price. However, painting is difficult precisely because of the fraction - colored and transparent coatings are strongly absorbed. The composition is selected according to the following criteria:
- No pungent odor. There are no completely neutral compositions. Subtle smells are still present. They can affect the master’s well-being. Water-based ones are the safest, unlike alkyd or nitro enamels.
- Quick drying. Water-based and acrylic paints have this property.
- Gloss required. The surface of the door is similar to a sponge and matte colour not too pretty on her. To do this, you will need MDF, which is poured into a container before application to release air bubbles.
- High adhesion. This parameter is written on the paint container.
- Small expense - for standard door– 200*80 mm, a kilogram can of paint and the same amount of primer should be enough.
The color is chosen according to the designer’s vision, but in no case should the door distract attention to itself in the future.
Preparing to paint an MDF door
Painting an MDF door yourself is not difficult if you follow the working rules. You will need tools: a spatula, rags, sandpaper, wood glue. First of all, it is important to prepare the canvas. For this:
- Remove the door from its hinges and remove the fittings. By the way, the handles on the new ones will also play a positive role in the interior, along with the chosen door color.
- Lay the canvas on a horizontal surface - this will prevent visible drips when painting.
- They remove old MDF from the old coating using two methods - heating or dissolving the previous layers. It is better to use the first method to prevent the MDF layer, which is already porous, from softening.
- The canvas is sanded. Old newspapers are laid on the floor to collect fine wood dust - it will come in handy later. You will have to do it manually - the MDF layers are too soft for mechanical action and in the absence of experience, the structure can be seriously damaged.
- Collect wood waste and prepare putty from them by adding wood glue to the dry mass. With such raw materials you can hide all defects without disturbing the structure of the door itself. After puttying, the areas are cleaned with fine sandpaper - this way, all chips and cracks will be hidden by natural material.
Particular importance is attached to the places where locks and handles are inserted - from constant activity they split the fibers of the door. They are impregnated with wood glue and cleaned.
To MDF painting has become of high quality, it is important to choose the right tools: brushes, rollers, sponges.
For a blank surface, rollers are suitable, and paint consumption will be reduced. It is better to paint inserts with brushes.
In addition to the above qualities, the paint must give the coating strength. This is what distinguishes glezal to a large extent:
- Does not change color. It can be added to the coating composition or used as an independent composition.
- Gives rigidity to the fibers. Painted MDF doors will become durable.
- Allows you to create textured surfaces. Aging, Venetian coating, bark beetle imitation and other decorations are made with a sponge or brush strokes. Gauze, rags, and film are placed on the glaze. By removing, an unusual structural surface is obtained.
The composition is mixed with the main coating or primer. Painting proceeds as follows:
- First, the canvas is primed with a large amount of drying oil. In addition to the varnishing effect, it will clog small pores and the surface will become uniform. It will take 2-3 coats so that the coating composition is no longer absorbed.
- After drying the canvas, MDF - acrylic or oil. You need to act quickly so that the strokes are uniform, without gaps. Two to three layers will ensure color and texture stability.
The finishing touch will be a layer of varnish. Actually, this is the whole process. Painting MDF is no more difficult than painting any other surface.
Requirements for coating layers
- Complete natural drying. If you decide to paint MDF at home in one tone, without any effects, then the color is best preserved by leaving each layer for at least two days. Proper drying time will allow the coating to become durable - adhesion will be fully demonstrated.
- Apply paint in one layer, without going over the same area twice. This one will do it without gaps. If you decide to restore the doors to an antique state, then they do the opposite - on the layer that has not yet dried, applying contrasting strokes with the end of a dry brush.
- Interior and entrance doors First they paint on both sides, then start on the ends. So, there are fewer drips on a flat area. Ends mdf doors must be protected from moisture penetration to a greater extent than the canvas - they are impregnated with water-repellent compounds before painting.
- If the old doors satisfy their appearance after cleaning, then natural style leave it - it is always appropriate. Use only varnish.
Requirements for tools and materials
- Rollers and brushes for painting are first soaked in a vinegar solution to make them soft. Hard brushes are suitable for creating complex effects - aging, for example. A fur roller, when interacting with caustic paints, will leave fluff on the surface, so only sponge rollers are used.
- Using paper tape will make the job neat. This is true for canvases with glass inserts or if you decide to paint the paneled parts a different color.
- Sloppy traces of paint for MDF, as well as drips, must be eliminated immediately. An ordinary sponge will be useful for this. You cannot rub the layer, just blot it once.
- The primer will reduce paint consumption, and the surface will become glossy and disappear. small cracks and other defects. Drying oil is an inexpensive and reliable option.
- Solvents will help remove mistakes on built-in locks. Cotton wool, soaked and placed inside, will not allow the mechanism to jam in the future. After work, it is recommended to lubricate them machine oil for good functionality.
Not difficultMDF, if you prepare for the process in advance - choose a style, coating material, and carry out the preparation. The result depends on the efforts made. Independent work will give savings family budget and will allow you to get an exclusive model of home interior.
The interior doors are laminated and stains cannot be removed (the paint is erased from the film). Can they be painted? And with what?
Paint a laminated door Can.
High-quality water-based paint paints the door quite well.
You still have to prepare the door.
I would recommend making the door surface matte and rough.
Then, using a special high-quality primer, prime the surface of the doors, and then paint with water-based emulsion. Don't waste money on quality paint if you want to achieve the desired result.
possible, but not advisable so how to achieve good result few people succeed. This is a complex process.
But nothing is impossible, if you are determined to paint the door, then first before painting it would be good to prime the door tightly and well, and then no problems will arise when painting the door.
Of course, a laminated door can be painted. The main thing is to choose the right paint and produce preparatory work. It is more convenient to paint the door in a horizontal position; to do this, remove it from its hinges and place it on a workbench or table covered with film.
Clean the surface on both sides with sandpaper until it becomes rough and matte, and prime. When the primer has dried, if there are defects on the door: chips, cracks, carefully putty, after drying, sand with fine sandpaper and apply primer again.
For painting the door paint will do, which is easy to care for: acrylic, oil, acrylate or nitro paint. Mix the selected paint thoroughly and apply to the surface using a brush or roller. It is better to paint in two layers, when it is completely dry, you can paint the door on the other side.
You can still try to remove stains, because the film is not reactive to some solvents - for example, white spirit, it should remove stains, but if you still need to paint, then do so!
Buy acrylic paint, after removing debris and dust you can paint without any preparation, acrylic paints are based on a solvent, it will melt the film and the paint will stick well.
In principle, you can use regular PF enamel or oil paint or even water-based emulsion, but the door will need to be prepared by either being completely sanded and the film torn off, or unwound, primed with a special acrylic-based primer, and then painted.
Doors are a large canvas - therefore, of course, it is advisable to carry out the work with a spray gun, you will save time, material, and the result will compare favorably with a brush or roller.
Of course, with appropriate treatment, you can paint the door. But I would recommend that you use self-adhesive film. Since your surface is already covered with a film, that is, on a laminated base, it will be easier to stick the adhesive film to it yourself. To do this you just need to select desired color and the drawing, and then degrease the surface and carefully stick the film on. To paste a film without air bubbles, you can use a method of applying an aqueous solution with detergent or soap.
It is possible if you first sand it with sandpaper.
How to paint a laminated door: features and processing algorithm
A smooth surface will not be suitable for painting. And then you can use paint at your discretion. Of course, not water-based, but you can choose any wood paint. This is how we painted it with acrylic.
Another option is to use wood-look self-adhesive paper.
More questions on your topic:
leave a comment
Builder's Dictionary:: Repair questions:: Calculators:: Special equipment:: Miscellaneous
2006 - 2017 © user agreement:: contact with the site administration [email protected]
How to choose laminate color and door color in accordance with the latest design trends
When deciding on the color of the floor and doors during renovation, one must take into account the fact that redecorating will be done more often. A good laminate And quality doors will last for decades. Therefore, whenever possible, the color of doors and laminate should be chosen so that it matches any new wall and ceiling design in the room.
How to choose the color of laminate and doors so that they blend harmoniously with common interior premises?
Interior decor in classic style and neutral color scheme
There are several basic colors natural wood used in the production of laminate, interior doors and skirting boards:
- Neutral light beige color scheme;
- Cold range of all shades of gray - from milky white to smoky gray;
- Warm yellow-red color palette;
- Black color of stained wood;
- White laminate and doors;
- A combination of two colors in a laminate pattern.
Advice.
To know how to choose the color and texture of laminate flooring and doors, you need to take into account that the glossy surface of the floor and doors gives the room solemnity.
Therefore, it looks bad in bedrooms and offices, where peace and comfort are expected. Therefore, in recreation rooms it is better to use a matte wood texture for floors and doors.
Combination of colors and wood textures in interior design
Before choosing a laminate for your doors, you need to know some of the features of combining wood colors in interior design. You can choose a door color that is contrastingly different from the color of the laminate, but still respect the color combinations.
Doors, floor color and furniture should be the same color - warm or cold.
It is important to observe the color combination of the laminate and doors, as well as choose the right color for the baseboard.
If the door light shades, and the floor is chosen in a contrasting dark version, then the baseboard is chosen to match the color of the door. For doors in dark colors The baseboard can be chosen to match the color of the floor or the color of the door.
Neutral range
Neutral color for flooring and door decor
If it is difficult to decide how to choose a laminate for your doors, then you should opt for a warm pastel beige or golden laminate color.
These colors include the following types of wood:
This decor can be combined with any design of the walls and ceiling of the room.
Advice. It is important that the wood does not have a red tint.
Because this color will be quite difficult to combine harmoniously with various shades of walls and ceilings.
Before choosing doors for red laminate, the designer must be sure that the decor of the room will be for a long time It is maintained in the same color scheme and the furniture in the room will not change.
Doors of dark wood do not go well with the red shade of the floor.
Demanding yellow-red palette
Interior decoration in sunny red colors
The red shade of wood chosen for the decor of laminate flooring and door leaves does not go well with cold blues, blues, as well as with calm colors of all shades of light pink, purple and lilac.
The combination of laminate and red doors can be harmoniously combined with the warm and gentle colors of early autumn:
Cold palette
If you decide to use cool wood colors in the interior design, such as:
- Bleached oak of various textures and shades;
Various colors of bleached oak
In this case, you need to be extremely careful when choosing the color of the walls and ceiling of the room. These colors are most often used for decor in a minimalist, classic or vintage style. It is better to choose the same door color and laminate color.
Gray color in interior design
This fact may surprise you, but the universal gray color is very demanding in terms of combinations and combinations. stylistic decisions. Gray shades of floors and doors are best used in the design of rooms in a classic style.
If the question arises about how to choose a laminate for gray doors, then you should opt for a floor covering (see how to choose a laminate) that is several shades darker than the color of the door of the same texture.
White color
Interior decor option with white laminate and doors in neutral colors
Determining how to choose the right laminate for doors white, it is advisable not to get too carried away with the game of contrasts. Although white is a universal color, it can play a cruel joke on a designer.
If color window frames And decorative elements white, then you should choose only white doors. And combine them with laminate flooring in light, warm shades.
A white door looks vulgar in combination with a dark wood floor - bog oak, wenge. Knowing how to choose laminate flooring and white doors, you can create a spectacular and unforgettable interior of any room.
Dark wood colors
Color of doors and flooring in one design
If you decide to decorate the floor with laminate made of dark wood, such as:
- Dark stained oak;
- Dark chestnut;
- Brown wenge.
It is better to choose the design of the doors in this color scheme. Dark colors when decorating the floor, they do not like contrasting solutions in the decoration of windows and doorways.
How to choose the right laminate for doors painted in dark wenge?
Fashionable shades of Wenge this year
It is important to immediately decide on the wenge color that appeals to you. And build on this general design premises.
Price for natural Construction Materials from wenge is very high. But there are many quality coatings for floors and doors with imitation of this valuable breed wood (see Wenge doors in laminate interiors).
It is not advisable to combine several shades of wenge in the design of floors and doorways. It is better to choose one color palette.
Important.
Black wenge is used only in interior design in modern style, since it should be emphasized modern furniture with abundance metal parts decor.
In a classic design style, this color is inappropriate, as it suggests a cold palette in interior design.
As you can see in the photo, this color is ideal for interior decoration in a modern or high-tech style.
Several colors in the laminate pattern
You can also combine laminate flooring in different shades with white doors and windows.
If a laminate that combines several shades and colors is chosen for interior decor:
Then the color of the front door must match at least one color used in the decor of the laminate. It is best to pre-order a 3D or decor design project to decide which option design will suit for a particular room.
Design rules for combining floor and door colors
Of course, you can, as required by the operating instructions, choose doors and laminate of the same color and shade (see what color to choose laminate). But sometimes interior design requires more daring and original solutions.
But there are several rules in interior design that should be followed, even if you decide to do the renovation yourself, without involving expensive designers.
- Doors and floors of light shades that are the same color and texture are chosen for small rooms facing north or west;
- The contrast between the door and the floor looks great indoors large area. But the combination of laminate and contrasting doors requires attention to the choice of baseboard.
Is it possible to paint a laminated door?
The baseboard should match the color of the lighter door.
- The colors of the laminate and doors should be either warm or cool.
The contrasting color combination of the laminate and doors should be pronounced. If this is not done, the design will be blurry and inexpressive.
The main rule of harmony in the design of premises should be adherence to the same style in the design of furniture, floors, window and door openings. And the choice of color and texture of the material and the decision on how to choose a design option depend only on the preferences and artistic tastes of the owner of the house.
How to paint a laminated interior door so that it becomes new and lasts a long time
Nowadays, laminated coatings are used more and more often. They are used to decorate furniture, interior and entrance doors, as well as other interior elements. In appearance, laminate resembles wood, which is why parts of it are used in construction and decoration. This coating is considered durable, but still, due to mechanical stress, laminated doors can receive flaws and become unusable. To give such door defects attractiveness and invigorate them with color, technological painting is used. Next, we'll look at how to paint a laminated door to make it last as long as possible.
Restoring a laminated door using paint
Over time, laminated doors become stained around door handles and scratches on the surface. It is quite difficult to remove such flaws, since the coating is not particularly amenable to this. Therefore the most effective remedy To correct the damage is to paint the doors.
Let us immediately note that treatment with stain and varnish will not be suitable, since for this process it will be necessary to sand the door and fill in all the irregularities with putty, and under transparent coatings all these errors will be visible.
Therefore, only an opaque coating or paint is suitable for painting laminated doors. But the work is not at all easy to do. Especially because the paint will not be able to adhere to the laminated surface and will flow off it. Therefore, you need to know the technology of how to paint a laminated door so that the paint on it lasts as long as possible.
Materials and tools for painting
Special enamel for painting.
Brush and roller.
Solvent.
Wood putty.
Putty knife.
Sandpaper.
Napkins and rags.
The surface of the door should be prepared for painting. The doors are washed, wiped and dried. All scratches, as well as the door leaf, are rubbed with sandpaper or a grinding machine. After this, dust is removed from the surface with a brush and rags.
Then putty is applied to the door leaf. It should lie in a thin layer so as to become one with the door. After the first layer has dried and sanded, a second one is applied, which is also rubbed down after drying.
When did I purchase the door? the desired structure, it is cleaned of dust and wiped with a solvent. Now the surface is completely ready for painting. Next, we’ll look at how to paint a laminated door correctly.
Painting a laminated door
The paint will need to be thinned, since the door should be covered with three thin layers paints.
Is it possible to paint a laminated door?
The material for painting should be one that is diluted with white spirit.
You should paint with a brush, this will allow you to better apply the coating to the surface of the door. The paint is not simply applied to the surface, but thoroughly rubbed into the door leaf.
After applying the paint, the door must dry completely. Only after this the second and then the third layer is applied. Each of them, after applying the next one, must be dry.
Now finished door coated with varnish to give it shine and attractiveness. The varnish can be applied either with a brush or with a spray gun.
Painting a laminated door with stain
How to paint a laminated door if there are no major defects on it, but the color of the coating is a little faded and worn off.
By using grinder The top layer of coating is carefully removed. Then the surface is rubbed with sandpaper and cleaned of chips and dust.
The door leaf is wiped with a solvent, and after it dries, it is treated with stain of the appropriate tone.
The stain should be diluted according to the instructions.
Apply the mixture to the door with a roller, brush or using a spray gun.
The technology of work is the same as with paint. It is necessary to coat the door leaf in three approaches, but not earlier than 12 hours after applying the previous layer.
After the final painting with stain and the surface of the doors has completely dried, they should be opened with varnish.
How to paint a chipboard door
Chipboard is one of the known materials, which are used to make furniture, doors and other products. What is this material made of? These are wood chips that are held together by formaldehyde resin. Wood chips under the influence of moisture and other unfavorable conditions can deteriorate and come apart. You can protect them by treating the surface with varnish or paint. Besides that coloring materials serve as protection, painting also gives decorative effect, because not only multi-colored surfaces are created, but also a variety of textures. So the question arises, how to paint a chipboard door to give it a beautiful look? To do this, you just need to cover the door with a new layer of paint. It is important to know what material the chipboard was originally covered with or whether the door is new and there is no coating at all.
Before painting chipboard, you should carefully prepare the surface. The final painting result depends on this work. To renew chipboard doors, transparent varnish or paint is most often used, which is applied to the surface. But this is not practical, since the paint begins to crack after a while. Removing this layer of paint later is not so easy and takes a lot of time. But this can still be done in several ways.
The surface of the door can be treated chemical composition. You need to choose it depending on what the door was treated with.
The surface can also be exposed to hot air, which can be supplied from construction hair dryer. Coming out, fairly hot air affects the old coating, destroying it. But then you can easily remove it with a spatula. But it is important to maintain a certain temperature so that the surface of the door does not deteriorate.
Then the surface needs to be cleaned of accumulated dust and degreased. Using a grout mesh (preferably coarse), clean the base of the door so as to leave small burrs. This is necessary in order to create better adhesion to the base. Apply a special primer. The primer is applied so that the glue that holds the wood chips together does not allow toxic substances to evaporate and moisture cannot penetrate inside.
Before painting a chipboard door, it should be puttied and sanded to remove any unevenness and differences that may have formed. Before puttying, a primer must be applied to the surface. For doors made of Chipboard is better apply acrylic primers. They tend to protect the base from cracks. The putty must be applied with a construction spatula, spreading it evenly over the entire door.
After the putty layer has dried, it is carefully sanded with fine-grained sandpaper. This procedure is carried out until all the irregularities are corrected. After this, the dust must be removed and painting can begin.
A good solution for painting chipboard would be a spray bottle or a special can filled with paint. With such tools it is easier to create a uniform layer without smudges.
What types of paint are suitable for this material?
Before choosing paint, you need to consider one thing: different types give paints different result staining. To increase the surface's resistance to mechanical stress, the base should be coated with varnish.
Painted doors acrylic paints will last for many years. They are not afraid of temperature changes and collecting steam, condensation and splashes of water. Surfaces painted with acrylic paints can withstand about 5,000 washes.
How to paint a laminated door with your own hands?
But the smell from such a helmet takes a long time to dissipate, which means it is better to carry out the work on the balcony or in the garage.
Before you paint a chipboard door, you need to know the painting technology.
The paint is applied in several layers. You can paint either with a brush or with a roller that has short pile. A roller with a long pile can leave a pattern that looks like an orange peel. If, after applying the paint, unevenness is still visible, you should apply it again. sandpaper, for sanding and apply another coat of paint. If you achieve the expected result using this method, you can proceed to the final stage - applying transparent varnish. It can also be applied in several layers.
The choice of paint quality and color is a matter of taste, but it is important that painted chipboard doors are in harmony with the interior.