Rocking chair made of corrugated pipe. DIY rocking chair at home

A rocking chair is a symbol of comfort, harmony and peace of mind. Unfortunately, purchasing this product is not a cheap idea. Prices start from 5,000 rubles and above. However, it is quite possible to make it yourself. In this case, you can think through your construction project and design.

How to design correctly?

There is a big choice finished drawings. However, when using them, keep in mind that they may be designed for certain individuals and are not intended for a wide range of people. To make the chair comfortable and meet individual needs, study the kinematics. Briefly described, the stability and convenience of the rocking chair depends on the location of the person’s center of gravity relative to the center of the generating circle. Remember, e If these two points coincide, then the so-called dead equilibrium is observed, in which the chair does not rock. Such a coincidence is rare, but it does happen. If the center of gravity is higher than the center of the circle, the structure will be unstable. To avoid such a scenario, the rocking chair is designed for the tallest and heavy man in family.

Remember that too sharp rocking can always be softened with a pillow under the back and on the seat.

Making skis

The comfort and smoothness of swinging depends on the runners. Let's look at two ways to make them:

  • The first option is simple and does not require much time.. We make skis from plywood no less than 1.5 cm thick. Using a pattern and a drawing, we cut out two blanks. We polish them . We cut grooves in the legs of the chair for runners with a depth of 7-10 cm. We install the skis. When installing, complete symmetry must be achieved. Having achieved harmony, we make through holes at the point of their contact with the legs of the chair. We treat them with glue and insert a wooden spike. The runners are ready.
  • Second option. We make the runners from a square meter block with a side of 4.5 cm. We cut grooves for the legs of the chair. We prepare the legs of the chair to fit them into the grooves on the skis. Soak the bars in hot water. When the wood becomes pliable, bend the runners into the desired shape and leave to dry. We treat the joints with glue and install dry runners on the legs. The skis are ready.

If you don’t have a ready-made drawing at hand, you can make it yourself. We construct the profile of runners of variable curvature in several steps:

  • Select the center point of the circle.
  • We choose a fixed angle, usually it is 10 degrees.
  • Draw a line that exceeds the radius of the center of the circle by 2-3% and mark a point.
  • Next, we increase the radius at each turn according to the law of geometric progression. The indicator is taken equal to 1.02 or 1.03. We also raise the center of the circle after each turn according to the same law.
  • We connect the resulting points using a pattern with a smooth line.
  • The runner profile is ready. It is better to take a scale of 1 to 5 or more.

The rocking chair is unlikely to turn out perfect the first time, so the resulting product must be balanced. A poorly swaying chair requires weighting the rear overhang. This problem can be solved by using a U-shaped beam connecting the ends of the runners. Weights need to be placed in the beam. It also happens that the rocking chair falls backwards. In this case, you need to weigh it down at the front. A footrest or weight attached to the underside will help achieve balance. In some cases it may be necessary to change the shape of the runners.

Most popular options

Before you take on the chair project and make it yourself, you need to study existing species. There are several product concepts depending on consumer needs:

  • With radius runners. The first version of the rocking chair that appeared in everyday life. It gained popularity due to its simplicity of design and technology. In most cases, it has a low landing due to unstable balance when swinging. At large amplitudes, capsizing is possible. To avoid this, the runners are made with a closing horizontal arc.
  • With runners of variable curvature. Their main advantage is the inability to tip over. Suitable for creating rocking cradles, as they guarantee safety and comfort.
  • Armchair Nirvana. There are two types: spring and elliptical. Rolling is smooth in both cases. However, there is a big difference in production and use. Spring models require special materials: high-quality wood or spring steel. In addition, they are unsafe and inconvenient to use. The gap between the skid and the spring becomes clogged with dirt and your fingers can get caught in it. Options on ellipses do not guarantee tipping over, but have a very light and pleasant rocking motion. The problem can be solved by installing bumpers. Elliptical rockers with an awning never tip over.
  • Rocking chair 3 in 1. The name speaks for itself. The chair includes a rocking chair, an armchair, and a lounger. The main advantage is versatility. The disadvantage is the large dimensions, which are not always possible in an apartment. In addition, the transition from one mode to another may be accompanied by unpleasant shocks.
  • Pendulum on bearings. An improved version of the classic chair. The difference lies in the fixed base and completely silent operation. Just like rocking chairs with runners of variable curvature, they are suitable for rocking small children.

The materials for making rocking chairs are varied and sometimes surprising:

  • Metal. An excellent solution for outdoor use due to its high wear resistance, durability and resistance to adverse conditions. external conditions. However, forged rockers require special equipment and skills, and the finished products are heavy. You can consider making it from profile pipe, it is better if there is an ellipse in its cross-section. To reduce the weight of the structure, and therefore reduce the moment of inertia, the seat is made of a different material.
  • Made from plywood. Suitable for carpenters with little experience. The main advantages of plywood are that it allows you to make precise connections, is lightweight and, due to its flexibility, is suitable for the implementation of non-standard ideas and solutions. The plywood product must be impregnated with any protective compound, be it acrylic lacquer or polymer emulsion. In this case, the product will last longer.
  • Made of wood. Traditional material for the manufacture of any furniture. Affordable, natural, eco-friendly and simple. Wood has high strength characteristics, a significant service life, and also has a pleasant appearance. However, in conditions of high humidity, the tree begins to rot. Solve this problem using various paint and varnish materials. Fortunately, there are many of them on sale.
  • From a professional pipe. Insensitivity to moisture, pleasant color and ease of assembly contributed to its spread. Plastic pipes They do not require glue and can be easily painted in any color, but there are also disadvantages. The main disadvantage is low strength. During use, parts of the furniture become deformed, lose their aesthetic appearance, and sometimes break.
  • From polypropylene pipes . Affordable, lightweight and durable. A flight of design thought will easily support a wide range of pipes presented in stores. The set of tools required for making furniture is minimal and includes a hacksaw, a marker and a tape measure. Suitable for lovers of unusual interiors.
  • From plastic bottles. The environmental movement is gaining momentum. In this vein, it is increasingly proposed to reuse waste. Plastic bottles- not an exception. The main thing is that there are a lot of them and that they look aesthetically pleasing.

Sketches of simple options

The simplest, fastest and cheap way make a rocking chair - make it from an old ordinary chair, attaching skis to it. We will need:

  • a chair with legs (if you don’t have them, you’ll have to make them);
  • runners;
  • screwdriver;
  • screws;
  • drill;
  • sandpaper;
  • paint and brush.

Manufacturing takes place in several steps:

  • Ski preparation. You can cut them yourself or order them from a carpenter. The distance between the legs of the chair should be 20-30 cm less than the length of the runners. We drill holes in the place where the legs are attached. Try it on - the skis should “sit” on your legs. If everything goes well, then you can start painting. Grinding the surface of the runners sandpaper and cover with paint. To achieve a deeper color, it is better to paint in several layers.
  • Installation of runners. We put the runners on the legs. To secure them, we drill holes in the chair legs for screws, insert them and tighten them. Turn it over. The rocking chair is ready!

How to weave?

The highlight of the interior can be wicker furniture. It will add comfort and harmony to the atmosphere. Advantages of wicker furniture compared to regular furniture:

  • environmental friendliness;
  • ease;
  • ease of operation;
  • ability to withstand heavy weight;
  • beauty.

Among the disadvantages are the following: cost and labor intensity of production.

Rattan and willow are most often used for weaving. Rattan is a plant from the palm family. Furniture made from it tolerates moisture well, so they prefer to install it under open air. It is environmentally friendly and has an excellent appearance. However, repairing such furniture will cost a pretty penny due to the cost of the material. A cheap option is willow. It is less flexible and unstable to moisture, like rattan, but is more accessible and therefore widespread. Perfect for home furniture.

A wicker chair made of willow, wicker or rattan is not so easy to make. Before you begin, you need to prepare the material. The vines are harvested during cold seasons. The raw materials collected at this time are easier to process. The harvested vine is kept for outdoors in a vertical position 70-120 hours. Raw materials are sorted depending on their purpose. Thick branches with a diameter of 5 cm are selected for the frame. For braiding, rods 1 cm thick are suitable.

Before weaving, raw materials must be processed as follows:

  • Soak the sorted rods in hot water for 10-12 hours.
  • Remove the bark.
  • We make shanks - we align the thin rods along the length and cut them into 3-4 parts.
  • We pull each shank through the press. The result should be ribbons of the same length.
  • We bend thick branches along the cylinders of the templates, secure them and let them dry. We make templates according to the drawing as follows. We apply the frame design to the tree and attach wooden cylinders to it.
  • We are waiting for it to dry completely. Most often it is 3 days.

Let's start assembling the frame:

  1. We attach supports to the frame. For reliability, we fasten them with cross bars.
  2. We install armrests and other parts.
  3. We secure everything with self-tapping screws and remove the temporary fastening.

Braiding of the structure occurs only on assembled frame in the following order:

  1. Before weaving, we knead the shanks by pulling them through any cylindrical object.
  2. Lubricate the braiding areas with glue.
  3. We weave. For structural strength, the frame should be wrapped in three rods.
  4. Inside, the weaving can be of different options - openwork, single.

Having finished with weaving, we install runners, supports and overlays:

  1. Turn the product upside down.
  2. Heat the installed pad with a hairdryer.
  3. We install it on the ski and wrap it with tape.
  4. Remove the tape from the cooled overlays and glue them to the runner, securing them with nails.
  5. After the glue has completely dried, replace the nails with self-tapping screws.

Before use, the chair must be treated with liquids that protect against fungus and wood pests, and the product must be varnished. If it is necessary to give the chair some shade, then before covering it with varnish it is worth soaking it with drying oil or paint.

Made of wood

A rocking chair made of wood is perhaps the lightest and simplest option after using an old chair. Garden tumbler benches have become especially popular. Their peculiarity is that they tilt 90 degrees when you lean back. The person sitting will be in a supine position with their feet pointing towards the sky. If you pull them forward, the bench will return to its usual position. However, making runners for such a bench is somewhat more complicated. They will not tolerate amateurism.

For smooth and comfortable rocking, it is better to use a proven drawing and accurately transfer it to the material.

Let's consider making a tumbler bench. We will need a jigsaw or a hacksaw for wood, sandpaper or a sander, a tape measure, a construction angle, a level, a screwdriver with a set of drills, a hammer, putty, a pencil and brushes with paints. The choice of materials is important to the performance of the finished product. We will make the side parts from plywood, and the slats from any elastic wood.

Let's get started:

  • We cut out the side elements from plywood with a jigsaw or hacksaw. We get a semicircular base with grooves for flannel.
  • We are preparing the slats. They can also be made from plywood if it is thicker than 30mm and has sufficient flexibility.
  • Using three bars 30x50x600 mm we connect the side parts to each other.
  • We attach the slats to the frame.
  • All that remains is to give the product an external gloss. Apply putty to the places where the slats are attached to the sidewalls to hide the recesses for the screws. We are waiting for the putty to dry completely.
  • We coat the bench with wood varnish and let it dry.
  • The tumbler bench for the garden is ready.

If desired, you can make the seat soft; for this you can use foam rubber. Another solution would be a removable soft case. It will last longer since it can be removed in bad weather.

Made of metal

Metal rocking chairs are more difficult to make. This will require special equipment and knowledge. However, they are perfect for the garden due to their high strength and wear-resistant characteristics. What can we say, your grandchildren will also be blissful in a metal rocking chair. Exist different variants manufacturing, but let's consider the simplest one. For this we need the following set of items:

  • steel bars and angles;
  • galvanizing;
  • Bulgarian;
  • welding machine;
  • drill and metal drill bits.

Let's get started:

  • We study the drawing.
  • Cut from metal profile steel strips 1 meter.
  • You need to weld the frame and weld rods to it, the distance between which is 1 cm.
  • We make the seat from galvanized steel and attach it with bolts. The holes are made with a drill.
  • We sand potentially dangerous areas.
  • Let's paint.

The main disadvantage metal furniture is its weight. Therefore, it is worth thinking about how it can be reduced. If the metal rocking chair will be used at home, it is worth gluing a strip of rubber to the runners to protect the floor from scratches.

For a child

Memories of homemade rocking chair will for a long time warm the souls of grown children. Making a rocking chair for a child is not radically different from making a regular chair. The only thing worth considering is the size and proportions, as well as the presence of handles. A rocking chair for children is often made in the shape of a horse, but this is no longer furniture, but a toy. Let's consider the simplest option. Necessary equipment: circular and miter saw, grinder, router, jigsaw and set of hexagons. Required materials: 18 mm plywood, cardboard, 2 threaded studs 50-60 cm long, 4 nuts for the studs and paint. We start manufacturing from the sides. We cut them out of plywood according to the drawing. We cut out the grooves. The thickness of the plywood determines the thickness of the groove. Drill the holes.

Cut out the seat. The width is determined individually. To ensure that the edges of the seat fit into the grooves, we narrow them tightly towards the edges. When cutting out the backrest, keep in mind that its width should be equal to the width of the back side of the seat. We collect all the parts and measure the resulting spacer size. When cutting, consider the size of the grooves. We sand the edges and install the studs under the seat. We saw off the protruding studs with a grinder. We tighten the sidewalls by tightening the nuts on the studs. Let's start painting. It’s great if your child takes part in creating the design of a new piece of furniture.

Restoration

Sometimes it’s easier to update your favorite things than to tear them away from your heart and just throw them away. They often remind us of ancient times family ties or pleasant events. It also happens that old furniture has not lost its wonderful properties, but its appearance leaves much to be desired. In this and other cases, restoration will help. Let's say you have a battered soft rocking chair with wooden frame. Worn wood and worn upholstery are striking. We will restore it at home. We will need: Grinder or sandpaper (the first is faster, the second is more interesting):

  • screwdriver;
  • acrylic paints;
  • new fabric for upholstery;
  • furniture foam rubber.

The operating procedure is as follows:

  • First you need to disassemble the chair using a screwdriver. We are tidying up the screws, we will need them later.
  • We remove the old layer of paint with sandpaper or a machine. The sandpaper should be fine grain. In case of heavy contamination, remove a larger layer.
  • Coating wooden parts acrylic paints, drying oil or varnish. Here you can use different painting methods. The worn effect is very popular now.

Replacing a seat

Let's start reupholstering the soft part of the chair:

The rocking chair is rightfully one of the most popular pieces of furniture. It gains even more popularity if there is country house. It can be different models, made from different materials. But more preference is given wooden products. You can buy it ready-made, or you can make it yourself. How to make a rocking chair with your own hands and what materials to choose, read further in the article.

Advantages and disadvantages of wooden structures

Wood is the most common material for making furniture. A wooden rocking chair is no exception, thanks to its numerous advantages:

  • Ecologically pure material emitting a pleasant forest scent.
  • Considerable strength.
  • Long period of operation.
  • Possibility of implementation design solutions.
  • Easy to process, including manual processing.
  • Wide selection of wood of any brand and anywhere.
  • Wide color spectrum of material.

The finished rocking chair fits well into any architectural ensemble of the building. It can be installed at any time in a convenient place: in a clearing, by a pool, by a fireplace, near a barbecue, etc. Rocking in a chair relaxes, creates comfort for the body and benefits the body. This is a comfortable and safe swing for children.

Photo: rocking chair in interior design

Along with numerous advantages, there are a number of disadvantages, the main one of which is the significant cost of any rocking chair. In addition, the structure is characterized by loss of its qualities and characteristics if it is exposed to rain, fog, and other precipitation. It is also undesirable to keep the rocking chair exposed to the sun for a long time.


Material and its characteristics

To make rocking chairs from solid wood, coniferous species are preferably chosen. It can be pine, spruce, alder or larch. These rocks are characterized by their low mass and low density. Homemade designs with significant mass it will be inconvenient to move. The high density of the material will create difficulties in work.


Coniferous trees have a light gray structure. Easy to process. A significant disadvantage of such wood is that as the humidity level increases, it increases in size. Despite this, conifers are budget option, are widespread in trading network and have little cost.

The chair can be made from more expensive types of wood. It could be oak, ash or beech. These types of wood have almost no pores, resulting in high level strength. Finished structures are reliable and durable, but have a high cost. Tree species have a light or light yellow color.

To make a chair that rocks, we use high-quality wooden blanks first grade. The moisture content of these workpieces should not exceed 10% at the start of work. If this indicator is higher, then wood is not recommended. It is better to let it dry, since a structure made of wet wood will subsequently dry out and be subject to deformation. The consequence will be its nondescript appearance or complete destruction.

Blueprints

To make a wooden swinging structure, you need to draw up a drawing of the chair. It is better to do it on graph paper, drawing all the structural elements with dimensions. To make a simple rocking chair from wood with your own hands, it is recommended to take an ordinary chair as a basis.

Drawing of a rocking chair made of wood

The simplicity of the design lies in the fact that all elements are attached at right angles and there is no need to cut additional parts. The basis for the entire structure is the size of the seat and the height of the legs. Will be cut to these sizes connecting elements. The next step manufacturing a rocking chair, according to the drawing and the required dimensions, we cut the wooden parts.

Seat square shape with a side length of 53-56 cm can be made of plywood or whole piece wood The thickness of the seat should be 1.0-1.5 cm. For the rear and front legs, a beam with a section of 4.5x4.5 cm is used. The rear legs are cut to a height of 105-110 cm, the front ones - 55-60 cm. To connect the entire structure, transverse slats are used, with the size length, height and thickness 57x4x1.5 cm, respectively.

This design and dimensions are not a dogma. Based on preference, the shape and size of the parts may vary.

Another example of a drawing

Tool

Making a chair requires the presence of tools. To complete the work you will need:

  • fine-toothed wood saw or electric jigsaw for cutting workpieces;
  • a simple or electric plane for processing structural parts;
  • grinder or belt machine for grinding parts;
  • manual milling machine for making grooves and processing connecting strips;
  • right angle or plumb line;
  • screwdriver;
  • hammer;
  • tape measure and pencil;
  • clamp or rubber band;
  • brush or spatula for filling mounting holes.

Considering that the structural elements will not be fastened with nails, a hammer will be needed to fit the parts to each other.

Connecting parts

To attach the seat and legs to each other, you can use two options:

  1. tenon fastening;
  2. connection with glue.

When fastening into a tenon on wooden elements Markings are applied to the rocking chairs. According to it, grooves are cut out in the legs, measuring 2.0x1.5 cm, 2 cm deep. The shape of the connecting slats is prepared for the grooves. Before fastening the parts, the groove and ends of the slats are treated with construction adhesive.

Users often search:

In the second option, the fastening points are treated with glue and connected to each other. For reliability, epoxy glue is often used. The joints are reinforced with self-tapping screws. The seat is mounted on transverse slats and is also fixed with self-tapping screws.

In both options, a clamp and gaskets are used to finally fasten all the elements of the wooden rocking chair. The cushioning material is installed between the clamp and the rocker. After installation, the clamp is tightened and the rocking chair is left for 24 hours for the glue to completely harden. In the absence of a clamp, the screed is carried out using a rigid rubber band.

Installation of runners

The manufacture and installation of runners can be done in two ways.

First way

It is characterized by simplicity and speed of implementation. It is as follows:

  • To make the runners, a sheet of plywood 1.5 cm thick is used.
  • Using a pattern, two pieces of equal curvature, about 1 m long, are cut out of plywood.
  • Slots are made in the legs of the chair, 1.5 cm wide to match the thickness of the plywood runners. The depth of the slots can be 7-10 cm.
  • The runners are ground along the edge and installed in the slots. During installation, it is necessary to achieve the most identical level of installation.
  • A through hole with a diameter of 2 cm is made in the places where the runners land.
  • The hole is treated with glue and a wooden spike is inserted into it.

Second way

More labor intensive. A block of wood is used as a ski. To equip a rocking chair with skis you need:

  1. IN wooden block, with a cross section of 4.5x4.5 cm and a length of about 1 meter, cut grooves.
  2. Treat the ends of the chair legs to fit into the grooves of the runners.
  3. Place the runner bars in boiling or hot water until the wood becomes pliable.
  4. Using a tool, bend the skis to a certain radius and leave them in this state until completely dry.
  5. Place the dried runners on the legs, having previously treated the grooves with glue.

In order for the runners to serve for a long time, it is necessary to use wood with high wear resistance.

Balance check

A rocking chair made of wood may be uncomfortable when sitting down or standing up. This occurs as a result of the difference in the weight of the structural elements that are located in its front and rear parts. To avoid discomfort, it is necessary to balance the swinging structure.

If the structure is significantly tilted forward, transverse strips can be mounted on the runners behind the backrest. If necessary, the weight on the slats can be increased by installing decorative elements.

Balanced rocking chair

When tilting backwards, the same counterweight must be equipped in the front part of the rocking chair. This could be an additional shelf for legs. If this weight is not enough, then you can install a niche under the shelf for additional counterweight.

Treatment

The finished structure will be used in different places when different temperatures. Operation in winter and summer, under the sun and in the cold, indoors and outdoors can lead to rapid aging of the tree and various diseases. Material processing will save you from this.

Before assembling the structure, the wood can be treated with stain. Due to its concentration, the rocking chair can take on any shade.

The chair is varnished in 3 layers

To prevent diseases, the tree must be coated with a special antifungal liquid, as well as a remedy against tree insects and pests.

To protect the wood from getting wet, it is recommended to treat it with a special water-repellent liquid.

The finished chair will serve not only as a piece of furniture, but also as a separate design element that will always attract everyone's attention.

6652 0 1

Do-it-yourself rocking chair from a profile pipe: drawings plus photo report on assembly

Do you want to build a rocking chair that will be comfortable, reliable and inexpensive at the same time? In this case, the chair must be made from a profile pipe. In this article you will find recommendations for making metal furniture and detailed instructions for assembling a simple and comfortable chair yourself.

Most popular options

There are many types of rocking chairs that differ in appearance and type. decorative finishing. However, when choosing an option for self-assembly, first of all, we pay attention to the design.

What to do if you don’t have a profile pipe, but you need to assemble a durable and beautiful chair?

Turns out, metal pipe with a round cross-section is no less durable than a pipe with a rectangular cross-section profile. Therefore, to make furniture you can use ordinary tap water. steel pipe. Another thing is that round section complicates installation, since the flying ones are more difficult to dock to each other.

Determination with chair type

Now that we know which chairs can be made from a profile pipe, all that remains is to choose suitable option. If you are assembling metal furniture for the first time, I recommend choosing simpler models. For example, it is not at all difficult to assemble a rocking chair on ordinary bent runners. To do this, you will have to bend two skis and attach a separately assembled metal chair with a backrest to them.

How to design correctly

If you are assembling a rocking chair for the first time, you can use one of the many ready-made drawings that have been tested in actually manufactured furniture. At independent design We take into account separate requirements for seat configuration and requirements for ski configuration.

The chair you design should be comfortable and durable. Both conditions are ensured by correctly selected sizes.

You can correctly determine the dimensions as follows. Find a ready-made chair or armchair that is very comfortable to sit in. Copy the dimensions of this furniture and transfer them to your drawing.

The situation with skis is a little more complicated. The length of the skis must be combined with the radius, so that assembled structure It swung with little effort, but did not turn over in extreme positions.

A universal rule: a ski 1.2 m long along the edge should bend upward from the floor surface by no more than 20-25 cm. Of course, the bend of the ski should be uniform without visible creases, which can lead to uneven swinging

Sketches of simple options

When it comes to simple options, we choose sketches of structures on curved skis, since such furniture is much easier to make than a chair on a pendulum or hanging cocoon. The simpler the sketch you choose, the better, especially if you do not have sufficient experience in making metal furniture. However, it also makes no sense to oversimplify the design of the chair at the expense of operating comfort.

Materials and tools

To work with a profile pipe, you will need the following tools:

  • Pipe bender with rollers for a pipe with a rectangular cross-section;
  • Welding machine with related accessories;
  • Clamps for metal;
  • Angle grinder (grinder) with cutting disc and a nozzle for grinding metal;
  • Electric drill with a set of metal drills;
  • Measuring tool (tape measure, square, marker, etc.).

What materials should I choose to assemble a simple chair? To make skis, a pipe with a cross-section of 40×25 mm will be sufficient. To assemble the chair we use pipes 30x30 mm or so. After assembly, it is advisable to cover the seat and back with a wooden board, since sitting on bare metal is not very comfortable.

And finally, in order for the finished chair to retain its presentable appearance for a long time, take care of purchasing high-quality paints and varnishes. You will need an acidic primer, which will prevent the formation of rust, and paint to apply in a couple of layers. However, you can do without a primer if you use special paints for unprepared metal. For example, Hammerite compounds are applied directly onto the rust.

Description of work

Illustrations Step-by-step installation of a metal frame

Making skis. According to most, this is the most difficult stage. In fact, if you have a pipe bender, there are no difficulties. Simply cut 2 blanks 1.3 m long and roll until you get an acceptable radius and a distance between the edges of the skis of 96 cm.

Please note that the skis must be the same, otherwise the chair will swing crookedly. You can check the sameness of the skis by placing them next to each other.

Assembling the sidewall. In accordance with the sketch, we weld diagonal posts to the ski. A cross brace is attached in the middle of the pillars - the seat guide. An armrest is welded at the top point of the diagonal posts.

Assembling the second side panel. The second sidewall is assembled in the same way as the first, but during installation we apply the structural elements to the finished part and make sure that they are identical.

We connect the finished sidewalls. We weld cross braces at the front of the skis. At this stage, be sure to use a square and check that the angle between the crossbars and the runners is straight.

We weld another cross brace at the top of the diagonal posts. The angle between this spacer and the diagonal posts must be straight.

We weld the backrest guides. Two pieces bent pipe We weld it to the seat frame and to the armrests. The backrest guides should be parallel to each other so that later, when covering with wood, the structure does not warp.

Painting the frame. The finished frame is cleaned of visible traces of corrosion and primed. After the primer has completely dried, a couple of layers of paint are applied with a break for the previous layer to dry.

So, the frame is ready, but the frame, even if it is well assembled, is not yet a chair. What to do with metal frame so that it becomes comfortable furniture?

There are several options for finishing metal furniture. For example, you can cut metal strips from sheet steel and weld them to the frame as slats that will hold pillows or a mattress. Another, more preferable option is to cover the metal frame with wooden boards.

Slats are cut from planed wooden boards and attached transversely to the frame. For fastening, holes with a diameter of 3 mm are pre-drilled in the metal frame. Lamels are applied over the drilled holes, which are attracted to the pipe with metal screws.

After the chair is completely assembled, the upholstery of the frame needs to be painted or varnished. Choosing a method finishing depends on what materials were used for the upholstery.

Let's sum it up

Now you know which chairs can be assembled from a profile pipe and how to do it yourself. If you still have questions about assembling metal furniture, ask them in the comments to the article.

October 25, 2018

If you want to express gratitude, add a clarification or objection, or ask the author something - add a comment or say thank you!

Planning the garden setting includes the selection of suitable products. It is not always possible to purchase elegant interior items in stores, and they are not cheap. The best option make a rocking chair made of metal with your own hands. The work will not take much time, and the chair will not take much space. Moreover, making it will be a fun process. The advantages of metal over wood are that the former looks especially elegant, and a chair made from it is highly durable.

A metal rocking chair is much stronger and more reliable than a chair made of wood.

Step-by-step instruction

There are several types of interior items made in this way:

  1. All metal chairs made using artistic forging.
  2. Tubular products created from aluminum or steel rods by welding.
  3. A combination of two materials, for example, metal and plastic.

Forging such products requires special skills and equipment. It is almost impossible to do this without skill. The connecting points in the second type are provided by welding or screwing the bolts with a drill.

The first stage of design is to develop a drawing. To do this you need to take the parameters regular stool and display them on a piece of paper. Manually draw an oval line at the base of the future chair. This way you can easily calculate the size of this semicircle. The larger radius ensures maximum safety. Then cut out such diagrams and attach these outlines to the original materials.

Then you will need steel rods measuring 20x20 mm. Cut them into 1 m sections each and weld them to the base, following the drawings exactly. Bend the steel following the oval and welding machine connect to the legs. The frame pitch should be about 6 mm.

Return to contents

Other options

A DIY rocking chair can be made of aluminum. For him, the base under the seat with the backrest is one piece and bends in the right place. In this case, tube arcs of a swinging mechanism with a 20 mm cut are used. Docking points are provided with screw fastening.

However, the most the best option- a connection of steel and wood, when the first is used for the base, and the second for part of the seat. The frame manufacturing technology is identical to the previous description. But the chair is equipped with a bed made of wooden planks. The joining of the upper and lower parts is carried out with screws. Drill holes in 50mm increments. Place the boards of the future chair according to the holes.

Before you start work, you need to think through everything carefully. And, first of all, you should know what exactly can be useful in the process of creating such a piece of furniture. Here is the exact list of tools and equipment:

  1. Steel rods with 20x20 mm cuts.
  2. Metal sheet, 2 mm thick.
  3. The ischial part is made of plastic.
  4. For fastening you will need steel corners with parameters 40x40x3 mm.
  5. Planks, 5 cm wide and 0.2 cm high.
  6. Welding device.
  7. Drill.
  8. Grinder and hacksaw for cutting raw materials.
  9. You will need a tape measure.
  10. Sheet and instruments for drawing.
  11. Set of screws.

A comfortable chair is the most important part comfortable rest, after heavy working days, both at work and at the dacha. Nice furniture It’s not cheap in the store, and the option of making your own models scares off many people due to the lack of instructions and the fear that it won’t work out.

Making furniture with your own hands will significantly save your family’s budget.

Moreover, the process of designing and creating a chair is in itself fascinating and interesting, primarily for its creativity and novelty of the work. But for quality performance you need minimal experience working with plywood and wood.

Experience can be gained by following step-by-step instructions.

The most important advantage of a plywood chair created with your own hands, is its price, which is much lower than the store price. In addition, hand-made chairs are in no way inferior to expensive factory ones, and sometimes even better - more original and reliable.

In the world of furniture design, there are famous names of designers who have made a name for themselves by making furniture from plywood.

Such designs are mainly made for country dachas as recreational items. average cost one product does not exceed 6 thousand rubles. Making, you can not only create a high-quality piece of furniture, save money, but also get great pleasure from your work.

What types of designer chair designs are there?

There may be hundreds and even thousands of design options, but they all come down to different variations of the 2 most popular models:


Given the necessary designs and minimal experience working with plywood sheets, both options will be easy to manufacture. True, a rocking chair can make you suffer when cutting out a template, plus the veneering stage will be difficult and time-consuming. Below are two detailed instructions for the production of rocking chairs made of plywood and an original model with three legs.

  • A structure made from plywood sheets should be environmentally friendly, safe and have a pleasant texture.
  • When purchasing, you need to pay attention to the thickness, since the method of processing in the future depends on it.
  • If the material has fibrous structure, when cutting or processing, chips, cracks and breaks are possible.
  • If the material is no thicker than 1.5 mm, then it is processed with a hand jigsaw, and for sheets up to 6 mm, electric is used.
  • If the work requires a cross cut along the grain, then a sharp knife is used to make cuts along the sawing lines.

It is better to pre-treat the sheets with special non-toxic protective agents before manufacturing.

Necessary tools and materials

First you need to prepare everything necessary materials and tools, namely:

  • Plywood sheets 15-20 mm;
  • Electric drill and jigsaw;
  • Sandpaper;
  • Thin nails with wide-brimmed heads and screws;
  • Metal rims;
  • Foam rubber 8 mm thick and upholstery material;
  • Paint (glossy) black and stain;
  • Wood glue;
  • Masking tape;
  • Tape measure, scissors and pencil.

Tools for work.

Step-by-step instructions for performing a model on three legs

  1. Engineering project.

It is better to start making chairs from plywood by carefully studying and calculating a drawing, which you can sketch yourself or find on the Internet.

Overall dimensions of the chair.

The drawing is taken as an example round chair made of spherical plywood. The model is different original design and ease of execution. It is better to take a birch leaf. For high-quality cutting, you need to prepare a template.

Drawing of the front legs of the chair.

  1. Making a template.

The drawing is redrawn on graph paper, then applied and traced along the contour.

Drawing of chair parts with dimensions.

  1. Cutting elements.

After a high-quality redrawing of the drawing, you need to cut out the elements with careful movements, while using the material sparingly.

If you rarely cut plywood, practice on an unnecessary piece, so you will not only get used to the jigsaw, but also decide on the cutting speed.

  1. Cutting out elements.

After cutting, you must carefully cut out all the elements with a jigsaw without damaging their structure.

During cutting, the movement of the jigsaw should be as smooth as possible - without acceleration or settings. Each jerk or stop will certainly leave a mark, and then you will have to sweat with it while polishing the cut area.

  1. Veneering.

The cut areas must be treated with sandpaper to remove excess roughness and prevent chipping and delamination during assembly.

Use different numbers of abrasive pads depending on the size of the defects.

  1. Treatment.

At first by special means with an antiseptic effect. Then comes the treatment with wood glue. This point is needed to prevent parts from scattering during assembly.

Pre-clean the surface from dust and dirt. Check the moisture content of the plywood, it should be completely dry.

  1. Product assembly.

Holes for screws and fastening points should be drilled according to the drawing diagram. Self-tapping screws should not be smaller or more product, bulging of any parts is unacceptable.

In order not to waste time sealing up “ugly” heads, use self-tapping screws with decorative heads.

  1. Putty.

After the assembly stage, protruding screws should be filled with putty. Coat the frame with varnish and let dry.

The number of layers of varnish must be at least two.

  1. Painting and upholstery.

To give a brown tint, the plywood sheet should be treated with stain. Afterwards you can make the upholstery of the seat and armrests.

For example, in the form of a soft pillow.

Making a rocking chair from plywood

  1. Engineering drawing.

In this case, as in the previous one, the creation stages begin with a drawing. You can draw it yourself if you have knowledge of product design, or take a ready-made one from the Internet, the main thing is that it contains all the necessary calculations.

An example of a drawing of a future product.

  1. Template creation and transfer.

As in the previous case, from the finished drawing, using graph paper, the details of the future rocking chair made of plywood are drawn, in our case these are the side parts (runners).

Drawings for a plywood chair are worked out on special graph paper.

  1. Cutting out products.

Using a jigsaw, cut out the parts along the pre-circled contours and process the edges with drying oil, then sand them with sandpaper. Treat parts of the product with special antiseptic agents.

Sidewalls of the future garden furniture cut out using a jigsaw.

  1. Final stages.

Fasten the finished side runners together using three crossbars, previously cut in the same order.

Connect the frame to the base using Euroscrews.

Side skids with outside reinforced with iron rims, which should be suitable in size to the overall dimensions of the product. The rims are secured with screws using a drill. The diameter of the hole is equal to the size of the screw.

Protruding caps can be covered with plugs, which are sold in construction or furniture stores.

At the final stage, slats and planks for the back of the rocking chair are cut out of plywood. Attach them with ordinary self-tapping screws.

To avoid distortions, mark segments on the side faces that will correspond to the intervals of the beams.

Fill the heads of the screws with putty, and cover the chair with varnish and paint.

Carefully cover the holes for the screws with putty.

Cover ready product antiseptic solution and water-resistant varnish.

To increase the comfort of the product, you need to make a foam seat for it and cover it with leatherette or any other dense fabric.If the chair will be used outside the home, then at the stage of cutting out the parts they need to be treated with an antiseptic. This way it will last longer.

What to pay attention to

In order to increase comfort, the rocking chair can be upholstered with soft artificial leather or velor. First, the back back is upholstered, then the fabric is nailed to the frame of the product with small nails. The edges of the transverse parts are sheathed at the back, and the upper and lower strips at the front. This is done to increase the strength of the product.

As a simpler option, you can make a soft back and seat for the chair.

If you don’t want to deal with complex upholstery or sewing pillows, then you can do it even simpler - make a removable cover. There will be foam rubber (10 mm) inside, and some nice furniture fabric on top.

In this case, the cover can be put on when needed.

On outside The backs can be applied with a mosaic or some beautiful pattern. Main- observe overall design interior, do not overdo it with bright colors and patterns. An analogue of this design will be a sofa.

Its width is greater, but the production mechanism itself is the same.

Afterword

This article discusses only two types of plywood chairs, which are the easiest to make for beginners. To make with your own hands for the first time, you need to put in maximum effort, endurance and patience. With a little practice, you can move on to heavier models.

A DIY plywood chair is stylish original solution, which is not inferior in quality to expensive store-bought counterparts!

VIDEO: DIY chair made of plywood and insulation.