Vase made of plywood. Wooden vase made from a flat panel
Plywood vase
For work you will need: jigsaw, files, sawing machine, sandpaper, drill or saw, pliers, wire cutters, screwdriver, hammer, BF-2 or wood glue, compass, ruler, pencil, copy paper, buttons, plywood 4 mm thick, round stick with a diameter of 14 - 18 mm, thin cord, some small nails and screws, Oil paint, colorless la To, a sharp knife or scissors and burning machine.
First transfer the development of parts through carbon paper to plywood, while not forgetting about the economical use of material. Draw straight lines with a ruler, round ones with a compass. In the drawings, the centers of the circles are marked with dots, and their radii with arrows.
It is very important to consider in which direction the fibers of the top layer of plywood will be located on the parts! When sawing on edges with outside There should be a thin trace of the pencil line. Thoroughly clean the edges of the parts with a file, and hard to reach places- a file. The tenons must fit tightly into the grooves of the mating parts. Finally, thoroughly treat all surfaces sandpaper.
Carry out preliminary (without glue) assembly of the products: you need to make sure that everything is done correctly. Only after this, lubricate the parts with glue and connect. Don't forget to remove any spilled droplets.
Queue for painting. If you decorated the parts with an ornament using a burning apparatus, then it is better to cover them with colorless varnish in 2 - 3 layers. And those without decoration, first paint them with oil or aniline paints, and then with varnish.
WALL VASE. cut out parts 1 - 10. Glue parts 2 - 9 into the grooves and slots of part 1. Insert a clean mustard jar into the resulting cavity. The bottom of the jar should rest on part 7. Drive a nail into the wall from the underside of part 10. Use wire cutters to bite off the cap so that the remaining stem protrudes 8 mm. Insert this part with a groove (without glue) into part 1 so that you can periodically remove the jar. The vase is assembled. Hang it on the wall using the hole in the top of part 2.
HANGING VASE. Cut out parts 11 - 14. Glue part 12 into one of the grooves of part 11. Take a clean jar with a capacity of 0.33 liters and put part 13 on its top part, and place the bottom of the jar on part 11. Then glue the upper part of part 12 with grooves into the part 13. Insert the remaining parts 12 and all parts 14 with glue. The vase is assembled. After final processing a vase of flowers can be hung by the “ears” on three strings in a bookshelf.
Wooden vases look very beautiful. Usually done on lathe. But 90% of the wood turns into chips.
There is a technology that allows you to make a vase from flat shield.
Here's what happens:
It took me a long time to choose the material to test. On the one hand, you want something interesting, on the other hand, you don’t mind spoiling it.
In the end, I settled on walnut, with oak and wenge inserts.
A walnut board 75mm wide and 15mm thick is cut into 3 parts.
4mm oak veneer must be cut into 15mm dies.
How to do it if not circular saw, but have a couple of clamps and a scoring saw?
Like this - the fist is clamped between the nut dies...
And sawing.
The result is an even die of the required thickness:
I glue the walnut into a shield with spacers - two oak dies, between them a thin wenge veneer. (which was sawn using the same technology)
Scratches from the saw are visible. A slight sloppiness, plus solid oak, which was sawed along the grain.
No big deal, the shield will still have to be sanded to even out gluing errors.
And again I glue it with spacers and leave it overnight:
I use a belt sander to level the shield and remove any remaining glue. Perhaps we should have made the wenge continuous:
The result was a shield 14 mm thick. It took 0.5 mm on each side.
Based on the shield and the desired dimensions of the vase, the angle and pitch are selected:
I print the drawing, use an awl to combine the centers of the shield and the drawing, glue the drawing:
I cut a small rake at an angle of 38 degrees:
I fix the shield with clamps on the jigsaw table and using the rail as a guide, I drill 2mm holes with a drill at an angle of 38 degrees:
I insert a file into the hole:
And let's go!
I cut the first ring:
And here it is - the bottom!
The wood is very hard, it is sawed slowly, if you press it a little, the file will burst. To replace the file, you need to return the table to a horizontal position, unscrew the fastenings of the file, thread the shield, again adjust it to 38 degrees, adjust the tension... Moreover, the file almost always breaks when there is 3 cm left before the end of the ring.
Second ring, the picture begins to emerge.
Bottom view:
And after the fourth ring, the files ran out. I used one and a half packs. No more, I'm putting it off until tomorrow.
I stopped by the store, bought 8 packs of saws (to be sure there would be enough), and sawed:
I'll move the rings:
Sleight of hand and no fraud, the rings are folded into a vase:
Can be combined with shift. You can make inserts between layers. There are plenty of options.
I start gluing without a bottom for now, to make it easier to sand the inner surface:
Checking the alignment of layers:
I leave it overnight under load:
Result. The surface is rough, but the alignment of the lines is without serious disturbances.
The darkening is traces of sawing with an ultra-thin file (41 teeth per inch), which sank into sawdust and the wood burned.
It is necessary to level the inner surface.
Attempt number one - a steel rod with glued on Double-sided tape sandpaper.
Not an option, too flexible.
Attempt number two, sanding drum on the same spindle.
It doesn’t fit either, the machine is lightweight (as I intended it to be). Doesn't hold up, plus it's inconvenient to work with.
Attempt number three. Sanding drum on a flexible sleeve.
The drum is small, sawdust flies where it is least needed, but you can work:
For fine grinding, I collect petals of 400 sandpaper:
But it doesn't polish. I continue with my hands.
It takes a lot of time, the surface is far from ideal.
I discover an error - the penultimate ring is glued with an offset of 180 degrees.
Well, this will be a reminder...In the end, it could have been much worse. Let it add charm - it will be a border. The main thing is that the spacers aligned properly.
The biggest nuisance is the sweat that pours into your eyes and falls onto the vase.
The respirator was once snow-white:
I glue the bottom. To speed up the process, I use my weight with dumbbells in my hands as a press... The vase can withstand more than 100 kg without squeaking, despite its lightness and thin walls. Now I’m thinking, what would have happened if the vase had shattered?
If your new hobby is sawing out various decorative elements, burning or carving wood, then our advice would be to start with a material such as plywood.
There are several significant reasons for this:
Plywood is quite easy to work with.
If it's in your hands good tool, and you'll start with the figures small size, then making them will only take you a couple of hours.
The material is universal in use, so you can make literally anything you want from it: furniture, toys, small decorative elements.
All this can be a wonderful addition to the interior of your home.
Features of working with the material
What is a plywood sheet? It consists of several sheets of veneer, which are connected to each other using glue.
Important: plywood can be different types: based on beech, birch, pine.
Not only the quality depends on which sheet you choose. finished product, but even its structure and color.
If you are going to cut out various figures using a jigsaw, then you need to choose the highest quality types of plywood.
They are particularly durable, which guarantees that the plywood will not crack, ruining the entire appearance products at the most unpredictable moment.
If you are going to start working immediately, immediately on the day of purchase, then choose only dry sheets of wood.
They won't break the jigsaw blade every 10 minutes.
To work with plywood, you will need to acquire a number of tools.
In principle, they are always the same for all types of products, so you only need a one-time investment:
- Jigsaw
- Jigsaw files
- Hand or electric drill
- Ruler
- Grinding machine
- Burner.
Framework
If you want to beautifully decorate your home or give it to someone close to you original gift, make your own plywood frame.
The preparation process will not take you much time, because you just need to get the necessary materials.
Note!
They are standard for all cases, and we have already mentioned them before.
We will offer you master classes on light crafts made from plywood. You can make either a regular straight frame or plan various patterns and figures on it.
First you need to make a template, and after that you can cut it out, trace the contours with a pencil on the plywood and begin the manufacturing process.
This stage is not only the most responsible, but also the most exciting. If you put a piece of your soul into your work, everything will definitely work out. Ready design must be opened with varnish. Ready!
Doll furniture
This task will be a real test for parents.
Note!
The so-called test of acquired design skills.
Feature of creation doll furniture is that children do not tolerate falsehood at all.
If they see that the furniture is not worked out in detail, but instead kitchen stove for your favorite doll you brought an ordinary block rectangular shape, then you simply cannot avoid serious grievances and childhood disappointments.
The second feature of making such a craft from plywood using a jigsaw is that all this furniture must be carefully worked out with sandpaper or a grinding machine.
Your child will constantly come into contact with these self-made toys, and if the edges are poorly processed, they may get hurt.
Note!
Well, the last feature of crafts made from plywood and the house is that the materials for such furniture must be absolutely non-toxic and normal for constant contact with the child, because he can drag it into his mouth or take it to bed with him.
This is not a simple applique or paper craft, so you need to take the matter seriously, following a whole list of actions that need to be completed.
Carrying out work from plywood
How simple furniture is made in detail, and then assembled into one piece of furniture, so do-it-yourself plywood crafts should be done separately.
To do this, first of all, prepare special drawings of plywood crafts, on which you will specify the dimensions of all parts and their fastenings.
Take a ready-made plywood sheet and attach a paper part template to it.
Trace the part with a pencil and plan out the outline with a jigsaw.
After this, each part must be cleaned with sandpaper or a grinding machine and only then the piece of furniture must be assembled.
When you are done with the entire set, open it with varnish.
Below are provided different variants and photos of plywood crafts. Choose the one you like.
Photos of plywood crafts
Description drawings of a plywood vase
Craft drawing Small vase for cookies - Plywood vase in the shape of a sports cup, drawings and tips. Vases Plywood Products cutting out with a jigsaw Burning carving! The difficulty in choosing plywood lies in the Posted in: Interior items, Drawings. The approach and structure of the vase have been radically changed. To cut out you need to have a piece of plywood drawings. For work you will need: a jigsaw, files, a sawing machine. Cutting out a vase from plywood. The site contains a collection of product drawings and photos of works. Interesting ideas and cutting drawings. It doesn't take much to make a vase. sheet plywood We give you the drawings of everyone. Now do-it-yourself plywood crafts. DIY plywood staircase drawings. Glass vases are held by cupids and voluptuous ones. The site contains a collection of product drawings and photos of works. DIY plywood box: making. Drawings for cutting out boxes and animals from plywood with a jigsaw: video - memo. Or maybe a complete drawing of the vase in jpg format. On plywood trim Literature on cutting out plywood with a jigsaw. From four existing types of plywood, only the first is suitable, at least the second. Homemade wooden fruit vase, made by hand, master class, drawings. Most books contain sketches and drawings for cutting with detailed description. Vases made of plywood drawings Vases made of plywood drawings Vases made of plywood drawings Vases made of plywood drawings Cutting out plywood with a jigsaw. The video shows the technique and assembly process. Drawings, drawings and descriptions of chandeliers, sconces and lamps made of plywood. Drawings, drawings and descriptions of plywood products for sawing. A jigsaw gives you the chance to make various internal holes. On this page you will find homemade drawings and drawings. Plywood thickness Large selection books and magazines on jigsaw cutting from plywood. DIY plywood crafts with a jigsaw drawings. Cutting from plywood with a jigsaw: a set of tools, materials, drawings and cutting technology Image result for crafts from plywood drawings. Sami Frame Cabin Wood Projects Vases. Drawings, drawings and descriptions of plywood products and homemade products. A similar drawing of this work is presented in the drawings section; boxes, plywood vases, corners. Drawings of Boxes for Cutting Out of Plywood with a Jigsaw Download Free. Sawing out of plywood with a jigsaw drawings Sawing out with a jigsaw from. Drawings The largest collection of drawings for cutting out of plywood has been collected. 1 Free jigsaw cutting plans and much more can be found exclusively at saw - man. Designed for the execution of a vase made of 4 mm plywood and a drawing for 6 mm. Literature on cutting out plywood with a jigsaw. A selection of material on the topic of plywood box drawings dxf. User publications Artistic cutting with a jigsaw. Drawings, drawings and descriptions of plywood products.
When the question arises: what to give Mom and do it yourself? Take a closer look at the Flower Vase; an original product, also cut out of plywood yourself, will serve as an excellent gift and will delight your loved ones. The work is of medium difficulty, follow the instructions, be consistent and you will succeed.
This work belongs to Lyudmila Pelymskaya, teacher German language, who dedicated for a long time such a hobby as artistic sawing jigsaw
In order to make such a Vase with your own hands, you will need the following tools:
Preparation of the workplace
As usual, the first thing you need to do is equip your workplace on which you will work. The rules are not complicated: there should be no unnecessary things on the table, all the tools should be in their place and at hand. Not everyone has their own desktop, and you’ve probably already thought about creating one. Making a table is not difficult, but choosing a place for it in the house is more difficult. A good option- this is an insulated balcony on which you can start working on your craft at any time. If you have a specially equipped room with a workbench, then you are lucky. In a separate article you can read about where I tried to describe in as much detail as possible the entire process of its creation. After you have completed the process of creating a workplace, you can proceed directly to your future craft.
Plywood selection
The main elements will fit on A4 plywood, since some parts need to be made in several copies, you will need several blanks. The thickness of the plywood should be from 2.5 to 3 mm, and depending on the thickness, sawing should be done along the internal or external contour, this is important for the grooves into which the elements of the craft are inserted. Before transferring the drawing to plywood, sand the workpiece with coarse sandpaper and then with fine sandpaper. Wrap wooden block sandpaper and then start sanding. Sand the prepared plywood along the layers, not across. A well-polished surface should be flat, completely smooth, glossy-matte in the light and silky to the touch. Pay attention to grain placement, knots, dents and other imperfections. Quality and color. If the plywood is not of very high quality and delaminates when sawing, read the recommendations for elimination. 
Transferring the design to plywood
You need to translate the drawing accurately and carefully: secure the drawing using buttons, double-sided masking tape or just hold it with your left hand. Check if the drawing fits the dimensions. Arrange the individual parts so that you can use the plywood sheet as economically as possible. There is no need to rush, because your future craft depends on the drawing. If time is short, then to speed up the translation process you can use the technique of quickly translating a drawing; for this, I suggest you read the article in the tips section:.
Cutting out a vase from plywood with a jigsaw
There are many rules for cutting, but you need to rely on the most common ones. First you should cut out the internal elements and then start cutting out the outline. There is no need to rush when cutting. The main thing is to always keep it straight at a 90 degree angle when cutting. Saw out the parts along precisely marked lines. The movements of the jigsaw should always be smooth up and down. Also, do not forget to monitor your posture. Try to avoid bevels and unevenness. If you go off the line while cutting, don’t worry. Such bevels and irregularities can later be removed using a flat file or “coarse-grained” sandpaper.
Rest
Fatigue occurs when sawing. Fingers and eyes, which are always tense, often get tired. When working, of course, everyone gets tired, but in order to reduce the load, do a couple of exercises. You can watch the exercises. Do this several times as you work.
Assembling a vase from plywood
The assembly of the Vase parts in this work is simple. When assembling, refer to the drawing. If some parts are not included in the required parts, file them down. When the craft is assembled without problems, glue it together. The dish must be glued using PVA or titan glue. You don't need to pour a lot of glue.
Varnishing crafts
If desired, the dish can be varnished with stain under valuable species wood or simply transparent, this is not necessary, but it will give great individuality Your craft. Try to choose a good and high-quality varnish. do it with a special brush, take your time. Try not to leave any visible streaks of bubbles or lint from the brush.