How to paste meter-long wallpaper alone. How to properly glue wide meter-long wallpaper

How to glue it correctly meter wallpaper? There are no fundamental differences from other widths. Only some positive points are added.

Advantages of meter wallpaper

1. Save time. and non-woven wallpaper is much faster than narrow wallpaper.
2. More holistic look. Since the wallpaper is quite wide, you will need much less wallpaper, therefore, there will be fewer seams.
3. Budget savings. It is cheaper to buy one meter-long roll of wallpaper than two half-meter rolls.
4. Ease of transportation. After all, it is more convenient to carry a couple of wide wallpapers than 5-6 50 centimeter ones.

Preparation for pasting meter-long wallpaper

• prepare wallpaper and glue for the type you have chosen
• prepare the surface: remove old wallpaper, take all recommended measures to avoid its further appearance. If the wall or ceiling is significantly uneven, you will have to resort to plastering. If the unevenness is small, you will not need such a drastic measure; you can limit yourself. By the way, meter-long vinyl and non-woven wallpaper can be thick (perhaps this is what you purchased), they perfectly mask minor defects walls
• the next step is to remove all sockets and switches and insulate the wires. Remove the ceiling and door frames.

Pay attention to the special symbols marked on the rolls. We are in one of the articles. Thanks to them, you will learn how to paste your wallpaper, especially if it is wallpaper with a pattern.

The process of gluing wide meter wallpaper

Now you can move on to preparing the canvases. To do this, measure the height from the ceiling to the floor and add 10 cm - this will be a margin for trimming. Don’t rush to cut the wallpaper over the entire area of ​​the room at once. There are times when, for some reason, you have to return a low-quality/defective product to its seller. So you will only lose on the cost of one opened roll.

Strictly according to the instructions, having previously purchased it specifically for the type of wallpaper that you have. We strongly do not recommend using all-purpose adhesives.

Or non-woven wallpaper, glue is applied only to the walls. Applying glue to the wallpaper will be unnecessary, but not critical. The same can be said about gluing vinyl wallpaper.

And here vinyl wallpapers on a paper base, you must first moisten it with glue for a while. Then fold the strip into an “envelope”: wrap the two ends to the middle with the coated side and again wrap the ends of the double layer to the middle. Some people simply fold the sheet in half, with the coated side facing in. Then we apply glue to the wall and mount the canvases on the prepared surface area (wall, ceiling). Wallpaper needs to be glued end to end.

Make sure that the wallpaper adhesive does not stick out at the joints during smoothing (when you remove the remaining air between the canvas and the wall). This is fraught with damage to the outer decorative layer and rubbing.

Do not forget that during pasting and until the wallpaper is completely dry, you cannot create drafts or ventilation. The wallpaper should dry under natural conditions.

If you still find it difficult to paste wide wallpaper, don’t worry, you can always call and invite our craftsmen. We are waiting for your calls seven days a week, ready to start work on the day/next day after your request.

Almost each of us had to glue wallpaper ourselves or help friends with this, so the technology of work does not raise any questions - apply glue and apply it to the wall. But today on the market you can find unusual wide wallpaper, the pasting of which confuses even some experienced workers. This wallpaper, needless to say, is very beautiful, durable and unusual, and in this article we will talk about how to glue meter-long wallpaper.

Meter wallpapers are becoming more and more popular every day - people want something new and “fresh”, and unusual and colorful wallpapers are just that. The width of the material is almost 2 times greater than the usual 53 cm. They come in 90, 110 and even 140 cm wide, and if you know how to properly glue meter-long wallpaper, you can only imagine how quickly such repairs will take place!

Of course, you have to pay a hefty sum for all the attractive new items, and wide wallpapers often scare ordinary people with their price tags. But those who have already dealt with this material unanimously claim that every penny spent is worth it - the wallpaper looks uniform, harmonious, lasts a long time and is unpretentious to use.

It's time to consider the advantages of meter wallpaper:

1. Gluing meter-long wallpaper is much faster and easier (using the equipment) than standard wallpaper.
2. The drawing turns out to be more complete.
3. Fewer joints and seams.
4. Wide wallpapers are produced only abroad using special technologies and high quality.
5. Despite the seemingly high cost of meter-long wallpaper, one roll will be cheaper than two rolls regular wallpaper the same quality.
6. Ideal for large rooms.

As usual, even the highest quality products have their drawbacks, and meter-long wallpaper is no exception:

1. Gluing them alone is quite problematic, especially if you are doing it for the first time.
2. Before pasting, you need to prepare the walls very carefully - wide wallpaper looks good only on perfectly smooth and even surfaces. Otherwise, the joints of adjacent wallpaper strips will be distorted.
3. Despite the impressive width, the length of the wallpaper may not be enough, which is why you will have to buy an additional roll, so you need to take accurate measurements of the area of ​​the room before going to the store, especially for rooms with non-standard square footage.

Preparatory work

Before you start hanging wallpaper and transforming your home, you need to go through several mandatory steps - prepare the walls and carry out calculations. Without this preparation, any idea is doomed to failure, so read the sections below carefully.

How to calculate wallpaper consumption

Correctly calculating the amount of wallpaper for repair will help you save an impressive amount and get the job done accurately and quickly. Many people decide to use it for this purpose. special program– online wallpaper calculator. But even the most good calculator will not help you with wide wallpaper, especially if you are lucky enough to own an apartment with a non-standard layout.

Carrying out calculations consists of several stages:

1. You should start with the perimeter, calculating it according to an elementary scheme familiar from geometry lessons: (length of the wall + length of the adjacent wall) x2. For example, if there is a wall 4 m long and a wall 3 m long, then the calculation will look like this: (4+3)x2=14 m.
2. Measure each wall separately along the bottom edge, making allowances for doorway recesses, recesses and protrusions.
3. Many people “subtract” doors and windows, reasonably believing that wallpaper will not be spent on them. But if you are not good at calculations and cannot calculate how much window and door openings take up in total, it is better to have a little material left over than to have to buy another roll in case of an error.
4. Is it necessary to glue wallpaper behind furniture? Ideally, yes. In general, before pasting it is advisable to remove all furniture from the room. But if we are talking about a bulky wardrobe covering an entire wall, which you are not going to rearrange for the next few years, then you don’t have to burden yourself with unnecessary worries and costs.
5. It is always recommended to keep a roll or half a roll in reserve. This is necessary in case of unplanned repairs, replacing a piece of wallpaper (a child painted it with a felt-tip pen, a dog scratched it, etc.). If you do not leave anything in stock, then finding exactly the same wallpaper on the market can then be quite problematic.

Surface preparation

When working with wide wallpaper, the most difficult and time-consuming task is not pasting, but preparing the walls. You should start this even when the ceiling is being finished, if you are dealing with a new building or doing a major renovation in the apartment.

What is the preparation of walls:

1. Remove the covers from all outlets and switches, and carefully cover the openings with electrical tape or masking tape so that it can be easily removed after work.
2. Remove all fasteners (nails, screws, self-tapping screws) from the walls.
3. Remove old covering (wallpaper, paint, etc.). It must be removed completely, down to the smallest pieces.
4. If necessary, level the walls by filling potholes and cutting off bumps. Dried putty should be rubbed with fine sandpaper.
5. Without fail, even on perfectly smooth and smooth walls One or two standing primers should be applied. It increases the adhesion force of wallpaper to the wall and significantly saves adhesive composition. The primer clogs all the smallest holes in the wall, preventing the glue from being absorbed into it and ensuring strong adhesion of the wallpaper. The glue must be applied to a completely dry primer. Drying times vary and depend on the number of layers applied. More detailed information indicated on the packaging of the primer composition.

If you have an apartment with catastrophically crooked walls, the alignment of which will take a lot of effort, money and time, it makes sense to consider the option of covering the surface with plasterboard. In this case, you can “kill two birds with one stone” - create a perfectly flat surface and make high-quality thermal insulation, which is especially important for modern apartments with thin walls.

A video on how to glue wallpaper and properly level walls will help you do the work quickly and competently:

How to glue wallpaper: instructions

When all preparatory work behind, you should check and, if necessary, replenish your construction arsenal.

To hang wide wallpaper you will need the following tools:

• a wide brush or flat construction brush with stiff bristles for applying glue (some people prefer to use rollers, but it’s better to start with a brush);
• rubber roller for ironing wallpaper;
• ruler at least 50 cm long;
• a simple pencil;
• construction plumb line;
• stationery knife;
• scissors;
• clean dry rags.

It’s best to glue wide wallpaper together with two or three people, because if you’re not used to it, it’s quite difficult to handle large pieces of material.

The technology for gluing meter-long wallpaper is as follows:

1. Measure the length of the wall with a tape measure and calculate how many strips of wallpaper will be needed to cover it.
2. Mark the first canvas. You should start from the window, moving deeper into the room. At 105 cm from the corner, draw a vertical line from the ceiling to the floor, using a plumb line and a ruler. Just in case, it is recommended to leave a couple of centimeters if the walls are not completely smooth.
3. When working in the corners, allowances should be left, which will subsequently be covered with a panel on the adjacent wall. This will prevent unsightly cracks from forming.
4. Cut the number of strips required for one wall, making a small allowance along the length of 2-3 cm.
5. Generously coat the wall with glue over the entire width of the panel, slightly going beyond the marked boundaries.
6. Since it is better to glue wide wallpaper for the first time with an assistant, one of you should hold the panel by the top edge, climb with it onto a stepladder to the ceiling itself and place the edge exactly to the boundary line of the ceiling and wall. The coincidence along the vertical border outlined in pencil must be controlled by an assistant.
7. Smooth the wallpaper to the wall with a dry rag or gloved hand, working from top to bottom and pushing air bubbles to the edges. Under no circumstances try to stretch the wallpaper horizontally, otherwise after drying you will find a completely different result than you expected.
8. Place the following sheets close to those already glued, applying them without overlap or gaps.

In most cases, it is not possible to fit an equal number of strips onto one wall, and you have to cut the panel vertically. Then the wallpaper on the adjacent wall should be applied to the corner, covering the cut so that there is no gap, and the glue that protrudes from under the material should be wiped off with a dry rag.

Excess wallpaper (length allowances) should be trimmed only after the panel has completely dried, since otherwise the sheet will most likely shrink in the corners, and crooked gaps will form near the floor, which cannot be masked even with a wide baseboard.

How to glue wallpaper alone

If it so happens that you were unable to get an assistant to hang wide wallpaper, you can handle this work yourself. There is an opinion that non-standard wallpaper can be glued with only one or two assistants, but this is not so. The width of the roll is more than 100 cm, and the human arm span is 150 cm, so you can easily handle it alone, joining the seams and leveling the panel.

The gluing principle is exactly the same as when working with an assistant. If the first time it was not possible to stick the canvas evenly, it can be removed and applied to the wall again - dense material, as a rule, allows this to be done without damaging the structure.

Pasting hard-to-reach places

Places behind radiators, in corners and areas above doorways always cause difficulties, especially when it comes to wide wallpaper. To glue the panel behind the battery, you will have to cut the panel into several small pieces. It is best to cut one piece to make it easier to recreate the original design.

It is quite problematic in such places to ensure that the pattern matches completely. And if an inexperienced person can still handle it above the doorway, then you can do this behind the battery only if you have the appropriate experience or design skills.

First you need to glue a piece of wallpaper onto vacant plot walls, and then align it along a pre-designated vertical. The second piece is glued to the opposite end of the battery, aligned as clearly as possible, and the seam is closed with an edge. It is unlikely that you will be able to perform such an operation perfectly the first time, so be patient.

Non-woven wallpaper will become best choice for inexperienced builders - their position on the wall can be easily adjusted as long as 10 minutes after sticking. But to make this possible, it is necessary to use adhesives without additives for rapid hardening.

Below are useful tips for beginners from professional builders which will help you learn how to glue meter-long non-woven wallpaper correctly and reliably:

1. Before gluing, prepare the walls as thoroughly as possible. It is impossible to overdo it in this regard - the more ideal the surface, the greater the likelihood that the wallpaper will stick more evenly and beautifully.
2. To improve the stability of the adhesive composition, it is recommended to prime the surface.
3. It is extremely important to create suitable temperature conditions indoors to ensure even drying of the glue. Otherwise, the wallpaper sheets may become deformed and the pattern at the joints will move.
4. During gluing and until completely dry, do not allow drafts to form.
5. The humidity in the room should be minimal, otherwise the glue will take a long time to dry, and the quality of work will leave much to be desired. At worst high humidity can provoke the appearance of fungi and mold under the wallpaper.
6. It is recommended to glue meter-long vinyl wallpaper in the summer (before the start of the heating season).
7. Please note that the wallpaper will be exposed to batteries high temperature long time, so they can shrink and move away from the wall.
8. In order to understand the process of gluing wide wallpaper, it is enough to make markings only for the first section. But if you are not sure, it is better to play it safe and mark the entire room, immediately counting and cutting the roll into required quantity canvases
9. Inexperienced builders who want to cope on their own are better off starting their acquaintance with the world of wide formats with non-woven wallpaper, since they do not need to be coated with glue (only the wall), and they are easier to handle than other types.
10. If you bought non-woven wallpaper, purchase glue designed specifically for it and recommended by the manufacturer.
11. It is very convenient to use two stepladders to ensure uniform leveling of the canvas on both sides.
12. Many inexperienced builders do not know how much time must pass after gluing before they can open the windows and ventilate the room. You should take into account the drying rate of the adhesive and the type of wallpaper, since for some a day will be enough, while for others it will take 3-4 days to dry. Information about this can be read on the packaging of the adhesive.
13. And the most important rule is to avoid drafts while working, otherwise, rest assured that you will have to redo everything all over again.

Meter wallpaper is gradually ceasing to be an outlandish novelty, and they can be found in almost any apartment. Another question is whether you will do the repairs yourself or prefer to pay construction company? We hope that after reading this article, you will not have any difficulties with self-gluing wide wallpaper.

For people who decide to update the interior decor by re-gluing wallpaper, information on how to glue meter-long non-woven wallpaper will be more useful than ever. Using this particular type of wallpaper for a novice builder is a completely unknown task, because previously, in most cases, walls were covered with standard-width canvases. But at the same time, there was also a production of wallpaper of non-standard, meter width. Using this particular type of canvas, you will have to completely change the sequence of repairs in the room.

The material for making meter-long canvases is practically no different from ordinary wallpaper, but the width finished products saves a lot of time and own strength for pasting the wall. In our article we will talk in detail about the features of choosing canvases, preparing the wall surface and how to properly glue wide wallpaper.

Types of meter wallpaper

Most of the wallpaper products produced are produced strictly according to a certain standard - 53 cm wide. Products manufactured abroad have a wider range of products, but in most cases the wallpaper has non-standard sizes.

Here are some examples:

• Wallpaper from German and Italian factories has working width canvas 70 cm or 106 cm.
• Belgian factories offer wallpaper roll widths of 90 centimeters, 100 cm or 140 cm.
• French manufacturers sell their products in the following established sizes - 90 or 70 centimeters.

Advantages and disadvantages of meter wallpaper

Before you purchase your favorite non-standard wallpaper rolls, you should familiarize yourself with the advantages and disadvantages of this finishing material.

Advantages of wide wallpaper:

1. In most cases, wide canvases are produced on a non-woven basis, which greatly simplifies the gluing process. To do this, simply apply glue mixture onto the wall surface and apply the prepared strip.

Important! Before gluing meter wide non-woven wallpaper, you must first level the wall surface with starting and finishing putty.

1. A huge assortment of wallpapers is presented not only with a non-woven base; on the racks you can choose paper-based wallpapers of various colors with a pattern that suits your interior.
2. When pasting walls with wide stripes, the number of seams is reduced.

Important! Walls decorated with this type of wallpaper are called seamless.

1. When using meter sheets on large areas The joints between the strips are almost invisible.
2. The process of covering the wall is greatly simplified due to fewer stripes.

Important! You will agree that it will take less time to cut 5 strips and apply them to the wall than to do the same process with only 9 pieces.

1. The cost of purchasing the necessary material is reduced.

Important! The cost of one wide roll is cheaper than two standard rolls.

Disadvantages of wide wallpapers

There are no disadvantages to this product as such, but there are some minor difficulties when working with them:

• Before gluing wide non-woven wallpaper onto the surface, it must first be prepared, visible irregularities, cracks and other defects must be removed.

Important! If you start gluing without preparation, you will not be able to achieve a perfect fit between the strips, which will ultimately affect the quality of the wall repair.

• Due to the large width of one roll, you may have a situation where a couple of centimeters of wallpaper are not enough to cover the entire room. As a result, you have to buy a whole wide roll, which leads to additional costs and a large number leftovers
• Having some experience in carrying out renovations, you can hang wallpaper of standard width on the wall yourself. In the case of meter-long wallpaper, it is better to find an assistant.

If after going to shopping mall If you have chosen canvases of non-standard width, then you just need to know how to stick wide wallpaper on a wall with your own hands.

Preparing the surface for gluing

If you are interested in the question of how to properly glue meter-long wallpaper, then, first of all, you should familiarize yourself with the principles of preparing the surface on which you plan to apply wallpaper.

Important! Preparatory process and you need to start gluing the walls when finishing the ceiling is not yet finished.

So, what actions are simply necessary for successful wallpapering with meter-long wallpaper?

• Take everything off installed switches and sockets. After dismantling, seal the holes with special adhesive tape.

Important! Using a special tape will save time after the repair is completed - it can be removed more easily and quickly.

• Remove from the wall all self-tapping screws, screws, dowels that were used to fasten shelves, pictures and other hanging objects.
• Remove the old wall covering without the slightest residue.
• In case too uneven walls should be treated with a dry mixture to level the surfaces or covered with plasterboard to additional insulation rooms from the inside.

Important! If the walls are affected by fungus or mold, then gluing wallpaper on such a surface is strictly prohibited. In this case, first of all, you should remove the affected areas with a special product.

• After treating the walls with a primer, install a special temperature regime, make sure that there are no drafts or overheating of the air.
• Before gluing wide wallpaper, apply a primer to smooth walls; with its help, microcracks and microscopic pores on the surface are eliminated.

Important! Treated walls will not allow the adhesive to be too absorbed into the surface, which will reduce the consumption of building materials and ensure strong adhesion of the wallpaper to the wall.

• If the installation of foam or other types of borders is planned, their installation is carried out before wallpapering the walls.

Required tools and materials

In order to carry out quality wall pasting, prepare all the materials in advance. necessary equipment. For this you will need:

1. A special wide brush for applying adhesive to the surface of the wallpaper;
2. Rubber roller for smoothing wrinkles and eliminating air bubbles;
3. A simple pencil for marking;
4. Scissors or stationery knife;
5. Cotton rags to remove excess glue;
6. Plumb.

Important! When purchasing a product from a specialized point of sale, be sure to check the compatibility of the adhesive with the base from which your wallpaper is made.

How to glue meter-long wallpaper?

Non-standard type wallpaper is divided into the following classes:

• Lungs;
• Heavy;
• Dense.

Although in most cases glue is applied to the surface of the walls, to be sure, check the instructions, because some canvases also need to be treated with glue. Next, we will consider in detail how to glue wide wallpaper on a non-woven backing so that the joints are not visible on the surface.

Important! Work, as in the case of standard canvases, starts from the window and moves in the direction of the incident light. When joining the fabric, be sure to accurately match the pattern or design.

The sequence of covering walls with wide wallpaper:

1. Before starting all work, measure the length of the wall to calculate the required number of whole strips.
2. Mark the location of the first strip of wallpaper - the marking is carried out from the window into the room.
3. At a distance of 105 cm, use a pencil and a plumb line to draw a line from the ceiling to the floor; if the corner is blocked, leave 1-2 centimeters.
4. Pay special attention to wallpapering in the corners of the room. If you do not have specific experience, it is better to leave a small overlap; it can be covered with a canvas on the opposite wall, thus avoiding the formation of an unaesthetic gap.
5. Next, cut required amount whole strips, taking into account a small allowance along the length.
6. Carefully coat the wall with adhesive, going beyond the pencil line.
7. To carry out repairs, call a partner:
   • One person should hold the wallpaper by the top edge while standing on a stepladder or high table and apply the sheet to the cut line of the ceiling, which is marked with a pencil or foam border.
   • The second participant in the process must regulate the coincidence of the canvas with the vertical marking line.
8. Using a rubber roller, moving from the center to the edges, push out any air bubbles that have arisen; remove excess glue with a cotton rag.

Important! You should not smooth the wallpaper horizontally, otherwise an unsightly gap will form during the drying process, as the wallpaper will shrink back to its original state.

1. Place all subsequent canvases close to the previous one, without gaps or overlap.

Important! It is not always possible to stick an even number of entire strips on one wall; the latter often has to be cut vertically. Glue the canvas on the other wall exactly from the corner, slightly overlapping it. Trim any excess wallpaper height with a sharp stationery knife only after the walls have completely dried.

Taping inconvenient places

In the process of pasting walls with non-standard wallpaper, it becomes much more difficult to apply the wallpaper in difficult places - corners, behind the radiator, above door and window openings.

Important! When finishing the ceiling, on the contrary, pasting will take less time. Firstly, you will need several times fewer stripes, and secondly, you will have an assistant, since wide wallpaper is quite difficult to glue for one person.

Here's how to make this task easier for yourself:

• To paste the surface behind the battery, cut the strip lengthwise into several pieces.
• It is quite difficult to combine the pattern in these places; this will require some experience. However, non-woven wallpaper has one positive feature: it can be moved within 10 minutes, so it will not be difficult to straighten the pattern.

Important! This option is possible if an adhesive is used that does not contain components that promote rapid hardening of the adhesive.

• A special feature of wide wallpapers is this: when rolled up, they look a little different than they do after being applied to the surface. Consider this fact when choosing a picture.

• To create original design premises, select decorative elements from the same collection as the wallpaper you selected.
• Pay attention to the quality certificate. Make sure of the quality of the selected product.
• If you were unable to apply the wallpaper evenly to the surface the first time, you can remove the strip, treat the wall with glue and repeat the procedure again.
• It is recommended to open a window or door in a room being repaired only one day after the work has been completed.
• To create an original design in a room, you can use several types of canvases in shade and texture at the same time. This way you can hide imperfections or highlight the features of your room.
• When choosing canvases, keep in mind that the horizontal arrangement of the pattern visually reduces the height in the room, while vertical lines and patterns expand the space.

Video material

Now you know how to glue 1-meter wallpaper in room. By applying the tips from the article in practice, you can easily decorate the walls of your apartment with non-standard wallpaper. Such canvases will help decorate your room, highlight the features of the interior and create a unique effect of a seamless surface. A large assortment finished products allows you to choose meter-long wallpaper of any color, shade, texture. However, be sure to pay attention to the characteristics regarding their wall coverings and the quality of the product.

IN Lately in shops building materials More and more often you can find wallpaper that is a meter wide, that is, a non-standard size familiar to our people. What is so good about these wallpapers that in a very short period of time they were able to win the hearts of the general public, how to glue them and is it worth giving them your preference?

Instructions.

1. wide wallpapers undoubtedly have many advantages over the usual thin types. Thus, meter-long wallpaper simplifies the work of pasting, reduces the number of seams, which often spoil general form rooms, and also reduce the cost of purchasing such material for wall decoration, since one meter-long roll of wallpaper costs slightly less than two similar small ones.
2. prepare wallpaper, special glue for non-woven wallpaper, a construction water level, a pencil, a tape measure, a roller and a bucket for glue, a plastic spatula, a soft bristle brush, a knife, plastic film and a roller for rolling the edge.
3. prepare the room. To do this, you need to completely remove the previous coating, level the walls if necessary, remove all sockets and switches, and insulate the wires. Mark the room. Marking should begin from the corner of the room, since the wallpaper will overlap there. Set aside one meter on both sides of the corner and use a pencil and level to make a vertical mark, approximately at the height of your height. Make such marks every 1.06 m (width of the tube), marking the exact distance with a tape measure.
4. Spread the film on the floor of the room so that the wallpaper does not get dirty and glue does not get on the floor. Determine the height of the wall by measuring it with a tape measure. Roll the tube face down onto the film. Mark your length (wall height) 10 cm.
5. Bend the roll and return to the starting point with it, so that by cutting off the length, you end up with two strips of wallpaper. Run your finger along the fold, making it smoother and more precise.
6. cut the folds with a prepared, well-sharpened knife. Prepare, therefore, strips of wallpaper for the entire room.
7. Dilute the wallpaper glue according to the instructions and let it stand in the bucket until it swells completely. Dip the roller into the glue and spread the area for the first panel (the first strip) on the wall. Take the first strip of wallpaper and apply it to the wall. It is important to know that pasting the strip starts from the top (from the ceiling) and stretches downwards.
8. Take a brush and smooth the panel along its entire length from the middle to the edges. Do the same steps with a plastic spatula. The canvas should fit tightly to the wall and have no bubbles. Cut off the margin left near the floor, if there is one. In this case, take into account the width of the plinth, which will be subsequently fixed.
9. Glue the second strip in the same way. When gluing a corner, the wall should be generously coated with glue. Here two strips of wallpaper are placed on top of each other, that is, the pasting occurs overlapping. In this case, the wallpaper is pressed tightly with a spatula and the corner is cut, after which the seams are evenly joined. Take a roller and carefully roll it over the seams. Carry out the same actions with other canvases, connecting them to each other along the intended lines.

Tip 2: how to glue non-woven wallpaper.

Non-woven wallpaper is sold either with a finished pattern already applied, or is intended for further painting. When choosing rolls with a thick texture, you can mask minor flaws left during wall repairs. Thus, if you like to change frequently color scheme surrounding interior, choose wallpaper that can be repainted 7-10 times. The non-woven base glides easily along the wall and makes it convenient to cover the walls alone.

You will need.
- Non-woven wallpaper;.
- Glue for non-woven wallpaper;.
- Building level;.
- Pencil;.
- Roulette;.
- Glue roller;
- Bucket for glue;.
- Polyethylene film;.
- Plastic spatula for wallpaper;
- Soft brush.
- Knife;.
- Metal spatula;.
- Plastic mesh in the glue bucket;
- Roller for rolling edges.

Instructions.
1. count how much wallpaper you need. Take measurements of the height and width of the room separately for each wall. Draw a plan on a piece of paper. This sheet will be useful to you when choosing wallpaper.
2. When purchasing wallpaper, pay attention that the batch number on the label of the rolls is the same. Look at other pictograms, the picture may need to be adjusted, or it may not. Don't forget to add another 10-15 cm to each panel as a reserve. Take out a piece of paper with the room plan and count how many selected rolls you need. 3. Prepare the room for wallpapering. The walls must be pre-leveled. Switches and sockets are unscrewed. Insulate the wires to prevent liquid from flowing inside the electrical boxes. Treat the walls with primer and dry.
4. mark the walls. Non-woven wallpaper has a good edge and is glued end to end. It is most convenient to start marking from a corner. There the panels will overlap, so that they can then be processed correctly. The width of the roll is 1.06 m. Set aside 1 m on both sides of the corner. Using a level and a pencil, make a vertical line to the height of your height.
5. Using a tape measure, measure 1.06 m from the drawn line in both directions, the size of the next canvas. In this way, draw all the walls in the room. Write the width of the panels on the wall with a pencil. You will immediately see where to glue the prepared wallpaper.
6. Spread plastic film on the floor. Roll out a roll of wallpaper face down on it. At this point, you should remember whether the wallpaper needs to adjust the pattern. Take this into account when cutting panels. If adjustment is not needed, then measure the height of the room with a tape measure and add 10 cm. Bend the roll onto the rolled part so that the edges coincide, then the fold will be even.
7. Run your hand along the fold and cut with a paint knife. Prepare wallpaper for the entire room. Roll the panels into loose rolls so that the design is inside.
8. Dilute wallpaper glue in a bucket according to the instructions. Pour water into a bucket and add glue in a thin stream. Stir constantly to prevent lumps from forming. Let the glue sit until it swells.
9. insert into the bucket plastic mesh to remove excess glue. Dip the roller into the bucket, run it over the mesh and coat the wall for one panel. 10. glue wallpaper on top. Take the edge of the canvas with your hands and attach it to the wall. Drive the roll down, smoothing the wallpaper with a brush from the middle to the edges. You can straighten it with a plastic spatula, just do it with caution so as not to rip off the design. The canvas should fit snugly against the wall without folds or bubbles.
11. Roll all the joints of the wallpaper with a seam roller. 12. When gluing a corner, the wall should be generously coated with glue. The two panels overlap. Press both sheets with a spatula and cut them along the entire length in the corner. Then the joints of the wallpaper will match. 13. Cut off the supply of panels near the floor. Consider the width of the future baseboard, which should hide the edge of the wallpaper. 14. Glue the top of the wallpaper with a fillet or border of the desired thickness.

More informational articles about good repair apartments

Many of those who are thinking about carrying out repairs with their own hands are interested in how to glue meter-long non-woven wallpaper. However, it is not even so important what material they are made of, since people are interested, first of all, in the features of gluing the canvases big size, that is, how to glue meter-long wallpaper in general, without reference to what they are made of.

However, the raw materials used in production still have specific value. However, first I would like to note that 1 meter wide wallpapers are becoming increasingly popular, despite the fact that they are a fairly new type finishing coating. According to its structure and general rules gluing, this material is no different from the more familiar rolls, the width of which is 0.5 meters (or, to be more precise, 53 cm). At the same time, the meter width significantly reduces the time and labor costs for gluing. Today we will talk about how to glue wide wallpaper and what are the features of such gluing.

By the way, if we talk about different countries, then it should be noted that in Europe, the USA and other “far abroad” wallpapers are often sold that have nothing in common with our standards, which were traditionally common in countries former USSR and the current CIS. A width of 0.8 or 1 meter is quite ordinary for them, and no one calls such canvases exclusive or non-standard.

Remember! Wider wallpaper has many advantages, including quick gluing and fewer seams on the walls of the room.

Pros and cons of using

Let's talk in more detail about what advantages and disadvantages there are of this material. If you are thinking about how to glue meter-long wallpaper on a non-woven basis (however, you can talk about any other canvas, for example, paper or vinyl), then you should consider both positive and negative qualities which he has this type decorative finishing.

Advantages

1. If you are used to gluing wallpaper using the “butt” method, then you can significantly reduce the number of these very joints, creating an almost seamless effect.
2. The process itself is accelerated, since it is possible to paste meter-wide wallpaper (including on the ceiling and in the corners) much faster.
3. In addition, you can often buy such canvases for more favorable price(in terms of 1 m2). Affordable cost is an important advantage, especially in cases where the budget for repairs is limited.

Flaws

At the same time, it should be said that gluing meter-long wallpaper is associated with some difficulties, which should also be taken into account:

1. Adjusting the length is quite problematic, especially for those who decided to take up gluing with their own hands for the first time. Sometimes this is the reason that you may end up with some excess material consumption.
2. If you don’t have a trash bin, then you should think about how to hang meter-long wallpaper on your own. The significant size of the canvases (or, to be precise, their width) makes it problematic to stick wide meter-long wallpaper for one person.
3. Before you apply 1 meter wide wallpaper, you will need to do more thorough preparation. work surface, since these canvases are extremely demanding in terms of wall quality.

How to properly glue meter-long non-woven wallpaper, video:

Step-by-step instruction

So, let's look at the gluing process in more detail, stopping at each stage. Here's how to properly glue meter-long wallpaper.

Preparatory work

1. The first step is to carry out high-quality and thorough preparation of the walls. To do this you need to remove all old Decoration Materials, which could be there, since their remains may interfere with good gluing. By the way, if we are talking about how to properly glue meter-long non-woven wallpaper, then here we should make a little reservation and say that in this case the task is somewhat easier, since in most cases such canvases are quite thick, which, in turn, says about the possibility of abandoning ideal surface preparation by completing this task, so to speak, “with a B.” At the same time, it is advisable to carry out processing with fairly coarse materials (including coarse-grain sandpaper), since in such cases the wallpaper will stick to the wall better (when compared with a perfectly smooth glossy surface).
2. In addition, we must not forget that when carrying out gluing work, it is necessary to tightly close all windows, vents and even ventilation holes to avoid drafts. However, they cannot be opened until they are completely dry. In some cases, it is recommended to dismantle sockets and switches after first disconnecting the electrical wiring in the apartment or house.
3. An important step is the preparation of the glue itself. As a rule, nothing complicated happens, since manufacturers almost always print instructions for preparing the adhesive composition on the packaging. So, even a beginner will not have problems with this. In addition, in most cases, the preparation of the adhesive composition can be done using any available means: you do not have to buy additional accessories or containers.
4. Marking the walls is also a fairly important task. Majority modern wallpaper, especially thick ones (vinyl and non-woven) are glued using the “butt” method. This helps avoid the formation of unsightly seams that occur when using the overlap method. For both wide meter and standard wallpaper, markings should be used, at least vertically. To do this, you need to outline at least one vertical line. For this you can use like building level, and a fairly simple device - a plumb line, which you can easily make with your own hands from literally any thread and weight. You can learn more about the direction of gluing from the article “”.

Sticking

1. When moving on to gluing, you should first cut the wallpaper to the required length. In cases where you need to match the pattern in adjacent canvases, you will have to leave a fairly large margin. In any case, even if there are no patterns and you don’t need to join them, always leave an overlap, both at the top and at the bottom. Its length should be at least 10 cm. On the one hand, this creates, but if you really want, you can use them, or something else.
2. Let's move on to gluing. Before you start applying the adhesive, it is advisable to re-mix it. The good thing about gluing meter-long wallpaper on a non-woven base (not only meter-long wallpaper, but also any other size, including standard ones) is that the glue can only be applied to the wall itself. It is not necessary to coat the back surface of the wallpaper. If you are gluing wallpaper of other types, then you will have to spread the glue both on their surface (of course, with reverse side), and along the wall.
3. Place the wallpaper against the wall. This must be done as carefully as possible. In addition, the first sheet should be glued, focusing on a straight vertical line that you outlined in advance. In order to avoid the appearance of “bubbles”, the pasted wallpaper should be smoothed using a special plastic comb designed specifically for this purpose. This can be bought at almost any hardware store.
4. Having finished with the first sheet, continue gluing the rest using the same technology. Of course, you also need to know how to glue meter-long non-woven wallpaper in the corners. The video or special instructions for this are no different from the principle of gluing standard wallpaper in the corners. Below is a video on how to do it correctly:

Advice! Any excess adhesive released when using a plastic spatula should be disposed of. A dry, clean cloth or sponge will help you with this.

What else needs to be considered

In addition to all the instructions, you must also remember useful tips, which, in any case, it is advisable to take into account before you think about gluing. Here are some recommendations:

• In addition to ensuring that there are no drafts, it is worth considering that the temperature regime is also favorable. This parameter greatly affects the drying of the wallpaper.
• The second tip is related to this: try to complete the gluing before the batteries begin to heat up. The fact is that in those places where there are working batteries, the temperature will be higher, which will affect the uneven drying of the canvases.
• If you are interested in how to glue wide non-woven wallpaper, please note that there are special instructions for each type of canvas. adhesive compositions. Although, on the other hand, some experts fully accept the use of universal adhesives.
• Since the width of meter-long wallpaper significantly exceeds the standard one, when gluing it, it is best to use two stepladders (or 2 stools, if you decide to make do with them). Since you will be working with an assistant, using a couple of stepladders or stools will allow you to place the wallpaper more accurately and level it better.
• By the way, even if you made a mistake when hanging meter-long wallpaper and applied the sheet a little unevenly, this can be corrected. Over a short period of time (maximum 10-15 minutes) you will have the opportunity to straighten the sheet somewhat. This must be done carefully, trying not to tear or damage the wallpaper.
• To make the interior more attractive, you can. By the way, they are also glued end to end. At the same time, make sure that the thickness of the combined sheets is the same.

Drying

Regarding the time during which the wallpaper different types completely dry, then it is, of course, different. For drying vinyl wallpaper, the normal temperature is between 18 and 30 degrees. Of course, in all places in the room it should be the same: if, say, the temperature is 22 degrees in one part of the room, then it should remain at the same level in other corners.

In general, heavier, denser fabric varieties tend to take longer to dry. Some (under certain circumstances) – up to 7 days. Concerning paper wallpaper, then they, as the lightest ones, dry for no more than three days, and only if we are talking about the so-called “duplex” (two-layer canvases). For simpler, single-layer options, sometimes 20 hours is enough.

Remember! It is better not to try to use certain types of heating, including heat guns, heaters and so on. The wallpaper should dry naturally. This applies not only to how to properly hang meter-long wallpaper on a non-woven base, but also to any other canvas.

Conclusion

In any case, before gluing, it is recommended to watch a video on how to glue wide meter-long wallpaper. Non-woven, vinyl or paper – that’s a separate conversation. Of course, each of these types has its own specific characteristics. Proper gluing determines not only the durability of the wallpaper, but also the attractiveness of the interior of your room, and the entire apartment in general. Therefore, try to approach the repair with full responsibility and remember that everything is in your hands!