How to seal a rubber boot. How to repair rubber boots at home

If your favorite hunting or fishing boots are damaged, do not rush to throw them away.

They can still be repaired using available tools and detailed instructions to action.

What to prepare to seal waders or fishing boots

For boots made of EVA material, you need to prepare a repair kit, which consists of two patches and glue.

You will also need:

• sandpaper;
• degreaser;
• protective gloves (you can use ordinary non-sterile ones from a pharmacy);
• piece of fabric;
• two plastic bags.

The patch can be cut from any durable, water-resistant material. Special glue should be used; in extreme cases, the universal “Moment” will do.

It is best to use “EVA shoe glue” in a white tube from the supplier KAYUR LLC. Its cost varies between 120 rubles.

For PVC boots You will need a repair kit consisting of two patches and glue.

We repair PVC boots

You will also find it useful:

• “fine” sandpaper;
• surface degreasing agent;
• protective gloves;
• napkins for removing excess glue along the edges of the patch;
• hair dryer (mounted or regular).

Any glue that is created specifically for PVC materials. For quick repair shoes during hiking, fishing and hunting, special repair kits are sold.

For example, KU-3105, consisting of glue and a transparent patch film. An hour after application, the glue dries completely. The cost of such a set is about 100 rubles.

Seal the hole in the boot step by step

Before you get started, here are some tips and tricks:

• do all work with glue only with gloves;
• carefully read the instructions on the glue tube;
• do not arbitrarily change the time intervals specified in the instructions;
• Do not use materials for which the selected adhesive is not suitable as a patch.

How to seal boots made of EVA material

1. Thoroughly clean and degrease the damaged area of ​​the boot. Taking advantage sandpaper To make the surface on which the glue will be applied rough, also sand the patches. This condition must be observed, since the glue does not adhere to glossy surfaces!
2. Reach your hand into the boot and push out the torn part of the boot. Apply glue to the sides of the torn part. WITH outside Gently push this part inwards, butting the edges together.
3. Apply glue to the patch and apply it to the damaged area from the outside.
4. Apply the patch in the same way on the inside and press it in place. To do this, place a piece of fabric wrapped in a bag into the boot.
5. Place a weight on top of the boot placed in the bag. A day after repair, the boots can be used.

VIDEO INSTRUCTION

How to seal PVC boots

1. Thoroughly clean and degrease the damaged area of ​​the boot. Using sandpaper to make rough surface on which the glue will be applied.
2. Apply a thin layer of glue to the damaged area and patch. It should dry, so stop working for 15 minutes.
3. Apply a second layer of glue to the previously treated surfaces. Leave for half an hour.
4. Using a hairdryer, carefully heat the glue and connect the torn parts of the boot fabric. Then, immediately apply patches to the outside and inside.
5. Using your fingers, gently but firmly, squeeze the gluing area for 1-2 minutes or roll it. Boots can be put on after the period of time indicated on the tube of glue.
6. If there is not a cut on the boot, but a hole, place a piece of paper under the surface to be glued so that the tops do not stick together.

VIDEO DESCRIPTION

Is it possible to repair a rubber boot if the sole is torn?

Depends on the nature of the damage. If a crack appears, there are several repair options.

• Buy elastic glue and fill the space in the crack with it. After it is completely dry, use sandpaper to clean the repaired part of the sole. How long will it last? One or two exits.
• For this method you will need a small piece of nylon the size of a crack in the sole and a soldering iron. The nylon is inserted into the crack and carefully heated with a soldering iron. Then it pushes into the crack in the sole. How long will it last? For two or three exits.

If the damage is more serious, there is no need to waste time repairing the boots. It will be easier and more reliable to buy a new pair!

And the question arises, ?

But after using the method of gluing with rubber glue, many people get upset because for some reason the patch falls off.

It’s strange that the glue is rubber, but it doesn’t stick to rubber?

Yes, it really doesn’t hold, and even if it does, it doesn’t last long.

Then we try another method, take it to a shoe repair shop. And there they say: “We don’t glue rubber shoes.”

It’s strange again, a shoe workshop, but they don’t take shoes for repairs.

And indeed, shoemakers rarely undertake the repair of rubber shoes. The only thing they can advise is to go to a car repair shop where car tires are vulcanized.

But, most likely, they will refuse you there, saying that this rubber cannot be vulcanized, or they will even say that they no longer have such a service, since now many drivers have switched to new types of tires where vulcanization is not used.

What to throw away? But I really need them.

Don't worry, there is a way out!

I offer you one of the most effective and proven methods, namely, how to glue a patch to rubber shoes.

Although it won’t add any beauty, the patch will stick.

IN this moment patch quickly and reliably rubber boots you can have a miracle with an invention that Lately used by cyclists.

It's called a camera repair kit.

It's not expensive but it sticks perfectly. Of course, I can’t guarantee 100% that it wakes you up exactly as you want, but I tried it, it works.

It includes ready-made patches, by the way different sizes, glue and even sandpaper (may not be available everywhere).
It is very easy to glue them. Instructions are always included with it.

I’ll add from myself:

• Mark the place where it is necessary to patch, applying the patch accordingly required size
• Sand well with sandpaper (some people advise degreasing with gasoline, but I would not recommend doing this at all if the shoes are clean and not greasy, and if degreasing, then only with acetone)
• Apply glue to the selected area on the boot
• Remove protective film from the patch and smear that side with glue (someone will have a question about which side to smear on the patch - I repeat the one under the film, but after gluing, a colored rim on the patch will be visible)
• Let the glue dry for about 10 minutes and press.

Of course, you shouldn’t wear it right away, wait a while, and it’s better to wear it the next day.

If a hole appears on the sole, then of course a different approach is needed.

First, this area must be treated with sharpening machine, so that the surface becomes perfectly smooth, otherwise everything will be useless. And then we glue it as usual.

But keep in mind that this patch will quickly wear out if you walk in it, say, on asphalt. That is, it is designed to go into the water, but not for long walks.

But in principle, if it wears out, you can do the previous procedure again.

So, it's possible quickly and reliably!

But as you noticed, we were talking about simple rubber shoes, which are intended for ordinary household chores.

Rubber shoes are incredibly popular in the off-season. And in gardens it is much more convenient to water and weed the beds, because no dirt or moisture is scary. At proper care and choosing the manufacturer, such shoes will last you more than one year.

How and with what to seal rubber boots?

However, no one is immune from damage to even thick rubber. We offer two simple and available methods, how to seal rubber boots.

Caring for rubber boots

So that such a nuisance does not take you by surprise, you should properly care for your rubber shoes. After all, even very good producers They will not be able to guarantee the safety of your boots if they are not properly cared for.

First of all, let's learn how to clean properly. To wash rubber shoes, just take warm water, soft cloth and just a little glycerin. Then appearance the product will last for a long time. Don't forget to ventilate your boots well to avoid the development of fungus.

After cleaning or use in very rainy weather, never place shoes on a radiator, dryer or use a hair dryer. Dry only in a warm, dry place or in a warm wind. If you purchased a model with a light or white sole, a regular school eraser will help make it look brand new again.

How to seal rubber boots - the classic method

Even if you take very good care of your rubber shoes, sooner or later they may deteriorate. In such a situation, the question quite logically arises: is it possible to seal the rubber boots, or will you have to go to the store for a new pair?

There is no need to panic, because it is quite possible to seal such a product. You don't even have to seek help for repairs. From the materials and tools used, you will need glue, solvent, and a patch (it is usually cut from old inner tubes from bicycles or strollers).

1. Shoes should be thoroughly washed and dried, as discussed in the rules for caring for rubber boots.
2. Cut the patch to size. In addition to bicycle tubes, old rubber boots are quite suitable.
3. Next, using a solvent, thoroughly degrease the surface of the shoe and the patch itself. Make sure that no pieces of cotton wool or threads from rags remain on the treated area.
4. To fix the patch we use rubber glue like Super torque for tires. If you wish, you can simply go to any nearest shoe repair shop and ask the master to sell you some special glue for a nominal fee.
5. First we apply glue to the shoes and the patch, let it sit for a while, then fix it. The exposure time is usually indicated on the tube.
6. To keep the patch as tight as possible, it is usually tapped a little with a hammer or something similar.

How to seal rubber boots - an alternative option

Sometimes the patch method is disappointing and you have to look for something else to seal your rubber boots with. If after a while you see that it was not possible to fill the hole, go to a sporting goods store. Many bicycle owners claim that more reliable way repair rubber boots; if they are torn, use a repair kit for bicycle tires.

Whatever method you choose, it is better to put on your boots after a day, when the glue has completely dried and set well.

Related articles:

How to wash sneakers in a washing machine? No hand wash can compare with the quality of an automatic machine, and sneakers washed in a machine will surprise you with their perfect cleanliness. We will tell you in this article how to properly wash sneakers so as not to spoil your shoes.	How to disinfect shoes from fungus? Foot fungus is a difficult to treat disease; it is much easier to prevent it, including disinfecting shoes. We will tell you how to do this correctly and what means to use in the article.
How to break in new shoes? Sometimes it happens that, having brought home a pair of shoes from the store, we find that walking in them is quite difficult and uncomfortable. In this article we will tell you how you can break in your shoes in this case.	How to clean nubuck shoes? Nubuck is a reliable, waterproof, but at the same time very difficult to care for material. We will tell you in this article how to properly clean nubuck shoes so that they do not lose their properties.

EVA stands for ethylene vinyl acetate and is an environmentally friendly, durable, lightweight, resilient and elastic material. It does not absorb moisture and odors, is easy to clean, in most cases it is used in the production of shoes and has the disadvantage that it is not resistant to sharp tools; such shoes will be punctured or even cut by a knot if the step is unsuccessful.

Therefore, repair is enough actual question for EVA products. Universal adhesives won't fit.

How to seal PVC or EVA rubber boots at home

Boots made from EVA can only be sealed with specialized material.

Characteristics of the adhesive composition

Sneakers, boots or winter fishing boots made of EVA material will be properly sealed only with the same material, i.e. EVA glue.

Properties:

• waterproof;
• does not spread;
• is able to tightly connect gaps formed at the bend, as well as side and corner ones;
• the repaired area remains almost invisible;
• means for a long time adheres to the shoe, thanks to which the damaged area is protected from repeated damage;
• the composition is consumed sparingly, since the manufacturer recommends applying it thin layer(otherwise the polymerization process becomes more difficult);
• inexpensive, a 15 ml tube costs about 100-120 rubles;
• Shelf life is 24 months (2 years).

How to use correctly

The method of working with EVA is practically no different from the usual one, you just need to take into account that it is impossible to glue PVC products with the product.

Instructions for use:

1. Clean the areas to be joined and degrease with acetone. You can do without degreasing, but in any case, the areas to be glued must be clean and dry.
2. Expand or compress the damaged area so that the porous surface of the ethylene vinyl acetate (usually inner side product) ended up outside. This is important because the glossy outer surface does not adhere.
3. Apply adhesive material to the porous area of ​​the cut (tear) and leave for three to four minutes.
4. After this, bring the edges of the gap together and press them firmly together.
5. The final hardening of the product occurs after a day (24 hours).

In a similar way, you can repair, for example, Toptygin winter fishing boots. The manufacturer indicates how to use the glue correctly on the packaging of the composition. Follow the instructions and the cut will literally disappear from your shoes.

Instructions

Cut out an outsole from thin microporous rubber.

Take rubber glue, glue “88” and mix both compositions in a 4:1 ratio. Apply the resulting mixture in a thin layer with an old toothbrush. sole boot and outsole. Try not to let the glue clump. The applied glue should dry for 5 minutes.

Now again spread the prepared mixture onto the leather sole. Dry the glue again for a few minutes and firmly connect the surfaces to be glued. Leave the item being repaired under the load for one day. Now trim the protruding edges of the outsole with a sharp knife. Your updated one is ready to serve you further.

Video on the topic

Sources:

• How to repair shoes

It often happens that the shoes still look quite good, but the soles have peeled off a little. What to do - run to the master shoemakers or try to eliminate the trouble on our own? Fortunately, today there are a lot of high-quality adhesives on sale. So if the sole has peeled off just a little, try fixing the boot yourself.

You will need

• - special glue 88;
• - ordinary rubber glue;
• - rasp or sandpaper;
• - a piece of cotton fabric;
• - iron;
• - rubber glue;
• - nylon;
• - soldering iron.

Instructions

Take special glue 88 and regular rubber glue. Mix one part of glue 88 and four parts of rubber and grind thoroughly so that there are no lumps left.

Next, take the boot and start cleaning sole. For this painstaking work, use a rasp or coarse sandpaper. Clean up sole you need to be very careful so that no dirt remains on it.

Spread both parts, that is sole and the boot with a mixture of glue, fold it well and then press the boot down with pressure, first making sure that the glue and the boot are as even and neat as possible. It is advisable to let the boot dry for about a day. After that it is already possible.

It happens that the sole falls off the shoe completely. Then it and the shoe need to be thoroughly cleaned in the same way, using a mixture of glue. Next, the glue is applied to sole. Leave it for about five minutes. After that, apply a second ball of glue, wait another minute and stick sole to the shoe, make sure it comes out neatly. After gluing, put it under pressure and wait about a day.

Another method of gluing soles can be used to glue a new sole to an old sole as a “prevention”. To do this, take an improvised adapter - a piece of cotton fabric. It needs to be welded to the old sole using an iron. Stick a rubber band on this adapter sole. For gluing, use the most common rubber glue.

If the sole has come off at -, then it can also be successfully glued. For this you need to clean it very well. Next, place a strip of nylon along the perimeter of the sole and a new one on top of it sole, then use a heated soldering iron to melt the nylon. After this, press firmly sole.

note

Remember that it's so homely renovation will do for boots and shoes if you are not afraid of the consequences of the experiment. If shoes are too valuable for you, then you should contact to a professional master.

Shoe repair is a responsible and serious matter. This is why many people prefer to have it done by a professional shoemaker. But there are also times when you have to repair shoes yourself. How can I fix it? sole?

Instructions

First of all, prepare the thread for stitching the sole. To do this, take a very ordinary thread and simply treat it with tar or wax. Thanks to this, the thread will become water-repellent and will not unwind into individual fibers due to mechanical stress. Then take the shoe. Now step back at least 5 mm from the edge of the grant and draw a stitching line in a circle with a pencil.

Take an awl that has a hook at the end. Pierce it along the intended line sole. Make small stitches with an interval of no more than 10 mm. Try to tighten each stitch as much as possible so that the thread in no case gives any slack and certainly does not form loops. The stitches must be made in such a way that the thread is not visible from the outside. In addition, it is recommended to make a small indentation along the seam line. But don’t spoil it by making such a channel. Better practice first.

There is another option for fixing the sole. However, it will require you to have skills in working with glue. Lightly strip sole coarse sandpaper or rasp. Take two types of glue: rubber and “88” glue. Now they need to be mixed with each other in a 4:1 ratio. Apply a thin layer of the mixture to the outsole and sole shoe with an old toothbrush. Try to carry out the entire procedure so that the glue does not form clots. Give the applied glue 5 minutes to dry.

Re-treat the leather with the prepared mixture. sole. Dry the glue again for a few minutes, and then firmly and forcefully connect the surfaces to be glued. Leave the shoes being repaired under a load for the whole day. Then trim the protruding edges of the outsole with a sharp knife. That's all the repairs. Your updated shoes will serve you for a long time.

If the soles of your favorite shoes or boots have become unglued, you can fix them yourself. Having at hand necessary materials, it’s not at all difficult to do. The main thing is to follow the instructions exactly. Then the shoes will serve you for another season.

You will need

• - pure gasoline;
• - glue 88N;
• - needle file;
• - soldering iron;
• - dratva;
• - awl;
• - shoe hook;
• - prevention.

Instructions

Before you begin repairs, determine what the sole is made of. Usually it is rubber or made of . If the sole is rubber, clean it of dirt and thoroughly degrease it using a clean one. After that, apply 88H glue on it and wait until it dries. This usually takes 10-15 minutes. Stuff your shoes with newspaper or any thick paper. Place it under the press for 8-10 hours.

If the sole is made of polyurethane, clean the bonding area from dirt and degrease with clean gasoline. Take a flat file and carefully file away the colored layer of leather. Degrease the surface to be repaired again. Using a heated soldering iron, spread small pieces of polyurethane (cut from the sole) over the skin in the area that needs. Squeeze sole and the upper part at the gluing site and pass a soldering iron between them. Keep in mind that of this type soles requires some training. Accurately maintain the pressure between the sole and the upper of the shoe and monitor the temperature of the soldering iron. The device must be very hot.

If the peeled sole has an edge that extends onto the shoe, it can be repaired in another way. Clean the damaged area from contamination and degrease with clean gasoline. Apply to sole and apply 88N glue to the upper skin in place. After 10-15 minutes, press as hard as you can sole to the top. Take dratva (strong twisted linen thread), rubbed with shoe polish. Using an awl and a special shoe hook, sew sole to the top of the shoe. Remember that the seam should be at a distance of 4-5mm from the top edge of the sole.

If they didn't appear small cracks, and it begins to peel off, you will need 88H glue and rolling (prevention). Clean the damaged area and degrease with clean gasoline. Apply glue to sole and for prevention. After 15 minutes, stick the roll on sole and place under a press for 8-10 hours.

Often, with active and constant use of shoes, they very quickly become unsightly: the seams begin to come apart, the sole becomes deformed or comes off. In this case, it will take a little time to get the boots in proper shape. With everything you need on hand, you can quickly seal your shoes yourself. Thanks to this, it will serve you for more than one season.

You will need

• - Sandpaper,
• - glue “Moment”,
• - acetone or gasoline,
• - a rag.

Instructions

Before we start repairs shoe, we need to prepare them properly for this. To do this, wash your shoes thoroughly with a brush and soap, rinse clean water and leave to dry in natural conditions room temperature at least one day. If the shoes do not dry enough, then it will be very difficult to glue the materials to each other, since the moisture will continue to evaporate. In this case, there is a possibility that they will break the next day.

Take a small piece of material or a regular cotton pad and soak it in acetone. Treat both surfaces to be glued properly, this way you will not only remove any remaining dirt, but also degrease the surface of the shoe. If the gap in the boot is large enough, in this case it is recommended to clean the surface of the material using fine-grain sandpaper. Thanks to this, they will stick together much better and stronger. For degreasing, you can use regular gasoline.

Apply enough good layer Apply suitable shoe glue to the gluing area and leave to dry for 10 minutes. After this, carefully connect shoe s and press firmly, hold for a while so that the surfaces can fix and remove excess glue. After that it remains to put shoe under a press for a day, this could be a chair leg or another object. For gluing shoes, Moment glue is best suited, which is sold in large tubes and has yellow. You should not use super glue, it will not give the desired result.

If shoe unstuck again, then there is a better way that will really help maintain the shape of the shoe - stitch it. In this case, it is advisable to contact a specialist - a shoemaker. If you decide to sew them up yourself, in this case you will need fairly strong threads and a thick shoe needle, as well as a lot of strength and patience.

Video on the topic

Helpful advice

Before going outside, especially in wet and slushy weather, be sure to treat your shoes with special impregnations and wax, which can be bought at almost any shoe store or market. This will help keep your shoes in good condition and your feet are dry.

Unfortunately, shoe soles sometimes crack. As a rule, patches installed on a crack do not give the desired result - the shoes continue to get wet, and the “patch” quickly falls off. How to repair a burst sole?

You will need

• - acetone or gasoline;
• - sandpaper
• - bicycle camera;
• - rubber glue;
• - shoe knife;
• - soldering iron;
• - nylon.

Instructions

Cut the edges of the sole around the crack to a width of 5-7 mm using a shoe knife. The cutting depth should be one millimeter.

Carefully measure the depth of the crack in millimeters. Add 15 mm to this value. Take an old bicycle inner tube and cut a strip out of it, the width of which will correspond to the result obtained.

Sand the strip using sandpaper. Degrease using acetone. Coat the strip with rubber glue on both sides. In this case, on one side the glue must cover the entire surface completely, and on the other side it is necessary to leave dry edges. The width of these edges should be 5-7 mm.

A torn boot is a great reason to buy a new pair. But this is not always possible. If the damaged shoes are expensive, very comfortable or well-loved, it would be a shame to throw them away. And here the question arises: how to seal boots securely and neatly?

It is better to take expensive boots to a workshop. Careless handling of glue can aggravate the situation. Professional shoemakers have a lot of experience, and they can make sure that not a trace remains of a hole. But if your hands are not for boredom, and curiosity outweighs the risks, then you can try it!

Choosing glue

If you are faced with the question of how and with what to seal your boots, you should under no circumstances use superglue. Caustic instant glue disrupts the structure of the material and makes the gluing area as fragile as glass. When worn, shoes undergo natural stretching and bend, the patch will crumble, after which the boots will become completely unusable.

Should only be used elastic types glue, for example, “Moment Marathon”. Professional shoemakers use Dismakol and Nairit adhesives, but finding them is not so easy. To ensure that the patch is as strong as possible, carefully read the instructions on the glue package before gluing your boots and follow all recommendations.

How to glue boots if...

Situation No. 1: the top of the boot has come apart at the seam, the threads have frayed

There is no need to seal anything. If the material is not damaged and holes from the seam are visible, such a hole can be easily sewed up with strong, thick nylon threads. Support the lining and approach the hole from the inside out. Repeat the seam exactly along the holes. If you make more holes in the leather, it may tear.

Situation No. 2: the leather (or leatherette) is torn in a smooth place

Such a hole is the most frustrating, because the sealing mark will still be visible. How to seal boots as discreetly as possible? You need to make a patch from the inside. Pick up a piece of thin leather or thick fabric, for example, raincoats. Apply glue around the hole, not reaching its edges 3-5 mm. Carefully joining the edges, press the patch. Turn the boot over onto your face. The unadhered edges must be carefully coated with glue using a toothpick and pressed firmly. The main thing is that the glue does not get on the face of the shoe, and that the edges of the hole are clearly aligned.

Situation No. 3: the material is torn at the seam

Glue a piece of leather to each side of the seam to repair the torn seam allowance. After the glue has completely dried, sew clearly along the original seam.

Situation No. 4: the sole came off

How to glue a boot if it “begs for porridge”? To ensure that the sole sticks firmly, sand the tear area with sandpaper and thoroughly clean it of old glue. Be sure to wipe the surfaces to be glued with acetone or alcohol before applying glue. To create stress, bandage the boot tightly.

To prevent shoes from deteriorating, it is important to wear them. It is better to save the boxes in which it was purchased and store the boots in them, then creases will not form on them and the leather of the boots will not be deformed.