Do-it-yourself installation of imitation brickwork. Imitation of brick with plaster: we decorate the walls to look like brick with our own hands

Brickwork (or its imitation) is often used in decoration various interiors. A surface finished with decorative brick always attracts attention and gives the room a fresh and unusual look. If previously only professional designers could create such a finish, now most home craftsmen can do it. There are several ways to decorate a brick wall, and all of them are relatively simple to implement.

Imitation brickwork Great for a high-tech room.

Materials for finishing walls under brickwork

Using real brick in interior design has a lot of disadvantages: labor-intensive masonry, narrowing of space in the room, large load on the floors. Replacing such bricks with facing ones solves almost all these problems, but costs several times more. In addition, for facing bricks must be properly cared for, otherwise appearance finishing will lose all its attractiveness. But there are other ways to decorate walls, less expensive and very effective.

Polystyrene tiles - economical material with high thermal conductivity and good noise insulation.

The following materials are used to imitate brickwork:

Tile - perfect option for the kitchen or bathroom, but only if you have the skills to install it. This type of cladding is not suitable for a living room, nursery or bedroom, so you should pay attention to other materials. The easiest way to decorate is brick-look wallpaper: there is a huge selection of colors in stores, and the gluing process does not require special skills. But there are also disadvantages here: ordinary paper wallpapers always look dull and cheap, and washable ones look too artificial.

Imitating masonry using decorative plaster is the most profitable option. Price consumables is relatively low, the finishing technology is simple and understandable, and the end result is as realistic as possible. When done well, it is almost impossible to distinguish imitation from real bricks. For greater effect, you can add a coloring pigment to the plaster.

It works well to finish a brick wall using thin polystyrene foam or ceiling tiles. This material is easy to use, light in weight and low in price, so making an imitation of masonry on a wall out of it is not at all difficult. Instead of polystyrene foam or polystyrene, many craftsmen use blanks made of wood, gypsum, and even tile adhesive, but wood requires tools, and gypsum bricks require molds.

Return to contents

Wall finishing with decorative plaster

For gluing decorative stone Regular tile adhesive will do.

Fast and convenient way finishing - applying decorative plaster. The main advantage here is that there is no need to level minor defects surfaces, because a layer of plaster will completely hide them. To work you will need:

  • primer;
  • paint brush or roller;
  • gypsum plaster;
  • spatula 10 cm wide;
  • coloring pigment;
  • dry rag;
  • small stick.

To form joints in real brickwork, it is used special tool- jointing, but ordinary plaster is also suitable wooden stick, a broken pencil, a ballpoint pen without a refill, or something similar that can be used to draw an even and neat seam. They begin work by preparing the surface: remove from the wall old finishing, seal the cracks in it, clean it of dust and thoroughly prime it. The decoration mixture is prepared after the primer has dried: the dry plaster is diluted with water in the proportions indicated on the package, and then the dye is added. If you plan to paint the walls after finishing, then it is not necessary to add pigment to the plaster.

The thickness of gypsum bricks should be about 5-7 cm.

Don't knead first a large number of composition in order to have time to process square meter surface before the mass hardens. The finished solution should slowly slide off the spatula without forming lumps. If this is the consistency, then you can start applying. Using a spatula or trowel, spread the mortar onto a section of the wall, and then level and slightly smooth the surface. You shouldn’t make it perfectly smooth, because natural brick is rough and sometimes even has small defects.

Now the most important thing is the formation of the brickwork. The sizes of the bricks may be different, but it is desirable that they do not differ too much from the standard ones and the wall looks as realistic as possible. You can draw seams under a ruler, creating a clear pattern, or you can do it arbitrarily - it all depends on the preferences of the master. Lines are drawn along fresh, uncured plaster with a dry stick, creating a pattern of brickwork, and excess mortar is removed with a rag. Then the next section is processed, and so on until the end. After this, the surface must be completely dry, otherwise further processing may damage the pattern.

The dried plaster is sanded with sandpaper to remove excess material and straighten the seams, and then wiped with a dust cloth. Before painting decorative masonry Cover with a layer of primer, so the paint adheres much better. If you want to give the finish a more realistic look, then individual bricks can be painted a different color. Sometimes they do it differently: first they cover the wall with a layer of gray plaster, level and smooth the surface well. Then a solution is prepared with the addition of red or brown pigment, it is evenly applied over the previous layer, and then the seams are drawn under the ruler. The red plaster is removed at the joints, resulting in neat bricks separated by gray lines.

Return to contents

Imitation of foam masonry

Tools for preparing the wall surface and installing imitation brickwork.

It’s also easy to create a decorative one from polystyrene foam or polystyrene foam. First you need to prepare everything you need for work:

  • sheets of polystyrene foam without a pattern;
  • felt-tip pen;
  • ruler;
  • sharp thin knife;
  • tile adhesive;
  • paint.

At the first stage, it is necessary to mark the sheets of foam plastic: draw even bricks with a side of 7x15 cm under the ruler with a felt-tip pen, making sure to make allowances for the seams. Next, use a knife to cut the foam along the markings and begin preparing the wall.

Image 1. To create roughness and cracks, you can use a drill with drill bits of different diameters.

Remove the old finish, eliminate defects, carefully level the wall and cover it with a primer. Apply a layer of glue to a clean and dry surface. ceramic tiles and put bricks on it; The gaps between adjacent elements should be about 2 mm. When all the bricks are glued, you can paint the wall, filling the seams well with paint and avoiding drips.

For greater decorativeness, small chaotic indentations and scratches are made on the surface of the foam blanks, which, after painting, give the masonry a slightly worn, but very natural look. The easiest way to create such a texture is with a concave tin strip, which can be cut from an ordinary tin can. Properly selected colors - dark gray, brown and red - add realism. IMAGE 1

IN modern design You can often find interiors with indoors. This effect creates coziness and makes the room “warmer”. But for the sake of such an element, it is completely inappropriate to make a real brick wall where there is none according to the construction plan. This is expensive, reduces the area of ​​the room, and also creates additional load on the foundation.

Just for such cases there are decorative panels with imitation brickwork. And if the store option for some reason does not suit you, and there can be a lot of them: price, quality, color scheme, shape, size, etc., then we can offer you a simple and inexpensive way imitation brickwork with your own hands. And the greatest advantage of this method is that it does not require special skills, for example, working with putty and other building mixtures.

To imitate brickwork you will need:

  • cardboard packaging boxes (thick cardboard is required)
  • PVA glue
  • hot glue gun and rods for it
  • thick paper napkins
  • tassel
  • pencil
  • ruler
  • utility knife or scissors
  • paints, varnish

Progress

The surface on which the brickwork will be imitated (it can be a wall or panel) must first be prepared. Clean the wall of old wallpaper, if necessary, prime it with a special construction primer or a 1 to 2 solution of PVA glue and water. If the wall was covered with paint, then wipe the surface from dust and degrease.

Imitation of decorative brickwork

There are quite a few varieties of bricks. It all depends on which one suits your interior best. And, if you have the opportunity to experiment with the color of the brick, then you need to decide on the size of the bricks right away. The main dimensions of the brick can be seen in the figure

In addition, the type of masonry depends on which side of the brick will be visible. Each side has its own name and will look completely different in the interior.

1 - bed
2 - spoons
3 - poke

Eat different variants decorative brickwork: e.g. outer side can be completely laid out with a bed or a spoon, or can combine different sides bricks

In our example, we will imitate red brick masonry; we will lay it with a spoon with dimensions of 228x65.

On a sheet of thick cardboard (packaging box) we draw out the “bricks” of the required size.

Then we cut the sheets along the marked lines using scissors or stationery knife and rulers.

The “masonry” in the interior can be either solid or reveal some kind of image to us. For clarity, in this example we took a photo from the calendar. In the interior this can be a drawing, photo wallpaper, stucco, etc.

Mark the boundaries of the drawing. If the boundaries according to the plan will have to go under the decorative brickwork, we place the drawing on the wall. We glue, we draw, we sculpt.

We cut some of the resulting “bricks” in half. This is necessary so that the masonry is staggered and looks realistic.

We begin to glue the “bricks” to the surface. This can be done with glue for heavy wallpaper, such as vinyl. You can use PVA glue or any other convenient for you to work with. After some experiments, I settled on this method: PVA construction glue + hot glue gun. If we consider them separately, PVA glue dries for a long time and does not immediately fix the bricks, and a hot glue gun, if used without PVA, uses up the rods very quickly. Therefore, we do this: apply PVA glue to the entire rectangle, with the exception of the corners themselves. We apply glue from a hot-melt gun to the corners. Hot-melt adhesive immediately fixes the “brick” in the right place, and PVA securely fastens it within 24 hours.

It is most convenient to start laying from a corner. We fix the first “brick” in the lower left corner.

We will fasten the next one at a certain distance, leaving space for an imitation seam of 07-10mm.

We will retreat the same distance from above, starting to lay out the second row. It will start with half a “brick” to create a checkerboard pattern.

When all the rectangles are glued, we leave them to dry for the time specified in the glue instructions. If it is PVA construction adhesive, then the drying time will take about a day.

When the glue has dried and the “bricks” are securely fixed along their entire length to the wall or panel, we begin decorating with napkins. This is to add texture to our brickwork and to hide the corrugation of the packaging board.

You need thick napkins High Quality so that, when soaked in glue, they do not tear or roll up.

Using a brush or sponge, thickly apply PVA glue on top of the rectangles.

We crumple the napkin in our hands to form folds.

And we apply it to the wall, in the place where the glue was applied. Apply glue on top of the napkin with a brush once again.

Select the gaps between the rectangles with a brush or finger.

This way we cover the entire wall. We make sure that there are folds and well-defined gaps - seams between the masonry.

Let it dry for another day.

When the glue dries and hardens, we begin painting.

The color is selected in accordance with the design. In this example we imitate red brick. By mixing white, orange, red and black paint we achieve a resemblance to original color bricks

And we cover the “bricks”. You can do this with a brush, or with a sponge, imitating the slightly porous structure of brick.

Then we go through the “seams” in the brickwork with a thin brush. You can also choose the color of the solution to suit your taste. But most often it has a slightly grayish tint.

Remember that after drying the paint becomes lighter than it appears in its liquid state. If after drying the color does not suit you, then the wall can be repainted until it acquires the desired shade.

When everything is ready, the folds on the bricks can be highlighted with darker or lighter paint, thereby giving the masonry a little antiquity and texture.

Apply paint of a suitable shade to the “bricks” with a dry brush.

It is best to varnish the paint on top to protect the surface from moisture and dust.

Such walls in the interior look very believable and beautiful. The work is not difficult, you don’t need to be professional builder or a finisher, the materials are available, and everything can be done to your liking, choosing colors and shapes to suit the interior.

Today, the use of brick or its imitation in design is very popular. It is used in various rooms and styles: loft, industrial, Scandinavian. Many people like the idea of ​​giving wall coverings an imitation of real brick, and there is nothing difficult in its implementation.

Finishing methods

There are two ways to perform this finishing. The first is gypsum tile cladding, which fakes the brick and is applied to wet plaster. The second method is to imitate brickwork when creating relief surface. This type of masonry will bring originality and freshness to the interior.

The surface of the walls, finished in brick, unites the strict lines of the rows and highlights the special decor of the texture of each square. The natural surface of brick is rough and uneven, so many people use its imitation. This finishing method is preferred to natural brickwork, and it belongs to architectural style loft.




Peculiarities

When choosing a material for this finishing, the following criteria are taken into account: aesthetics, price and harmlessness.

In this case, plaster to imitate brick is the most suitable option, which has a number of advantages:

  • Purchase of this material without large financial investments.
  • Wall cladding takes relatively little time.
  • This coating is applied thin layer, and you don’t have to worry about narrowing the room.


  • This coating is easy to apply yourself, without involving specialists and avoiding additional costs.
  • Brick-like plaster can be used to decorate not only the surface of the wall, but also the kitchen backsplash, corners or doorways.
  • This plaster imitates the finishing of expensive clinker tiles.




How to choose plaster

Before starting work, you must purchase everything in advance necessary materials. In terms of imitation of brickwork, gypsum plaster is most acceptable, while attention should be paid when purchasing the following characteristics material:

  • It should be easy to apply and have elasticity.
  • It is important that there is no shrinkage property after hardening.
  • Before use, there should be no preliminary or additional puttying of surfaces.
  • The material must be environmentally friendly and harmless.




But preference should still be given ready-made mixtures, they have greater elasticity and ease of use. This material, diluted to the desired consistency, is sold ready for use. This mixture is a homogeneous mass that can be applied immediately. The advantage of such plaster is that the container with the remaining mixture is tightly closed, and it can be used even after a long time.




Dry mixtures can be varied and heterogeneous. They include various components, for example, an additive in the form of large stone chips. To do this, the manufacturer indicates on the packaging for which surface this composition is suitable.

For priming the working surface, many different compositions are also produced in liquid and paste form. But before this type of work, it is better to treat the wall liquid composition deep penetration.

Application process

Before you start creating a simulated brick surface, you need to find out whether the walls are suitable for such work. They must have a flat surface and not a “littered” condition; a suitable wall relative to the floor has an angle of 90 degrees. The absence of large holes, bumps and dips is important. If there are any, using cement mortar, beacons and plaster mesh alignment must be done.



You can assess the condition of the surface by applying to it long rule. If gaps of more than 3 cm per meter of length appear between the rule and the surface of the wall, proceed to leveling.

If there are small defects (cracks, small irregularities) on a straight wall, there is no need to plaster it, just repair the defects with cement or putty. After complete drying, you need to treat the surface with a deep penetration primer, first mixing glue into it. Primer treatment is mandatory, otherwise the decorative layer of plaster will begin to peel off and fall off over time.



Before work you need to check plaster mortar , prepare an auxiliary tool so that it is always at hand if necessary: ​​a roll of tape, a wide and narrow spatula, a rule or laser level and a cord for displaying beacons. It is very convenient to mix the mixture with a drill on which a mixer is attached - a special attachment for thorough stirring. To avoid damaging the flooring, lay down oilcloth.

After completing all necessary conditions you can start guiding plaster mixture. The simplest and most applicable method involves adding color to the induced solution. You just need to dilute the dry solution as indicated in the instructions for use, add the coloring element there and mix everything thoroughly using a mixer.


If you have never encountered similar works, in this case, you should not apply too much solution. After some time, you need to try to work it out, otherwise it will set and become unusable for application. The solution must be adjusted to a certain viscosity until it acquires the consistency of thick sour cream and begins to slide off the spatula evenly, without falling in pieces.

The induced solution is taken on a spatula and thrown onto the surface, while smoothing it upward. If you want the surface to imitate brick, do not try to level the applied mortar too smoothly. Brick does not have a smooth surface; it is usually uneven and rough.

When decorating a brick, you must take into account the width of the seam, if not this condition the finished surface will look unnatural. In this case, the dimensions of the most common brick are not very important, since this material is made both elongated and square.



Currently, textured and relief non-standard bricks are produced. And this look can be imitated by this plaster. When starting to carry out such work, it is preferable to have some experience gained in finishing imitation of ordinary standard brick.

When applying seams between falsified bricks, use a ruler, or better yet, a rule. Then the line will be perfectly straight. If you want a curved line, you can draw it freehand. The seam must be done before the solution hardens on the surface. When carrying out stripes, excess will appear, which can be easily removed with a dry cloth.



In this way, each applied pattern is “drawn” in turn. A prerequisite is that the coating must be damp; the decor must be applied before the solution sets or hardens. After this process, the surface is allowed to harden and it is not recommended to touch it during drying. To obtain the original texture of bricks, you can brush over the decor with a dry and hard brush.

After the wall covering has dried and become strong, use sandpaper and sand the decor, but this depends on your preferences. The last point is the removal of all unnecessary plaster elements that spoil the design. Subsequent processing of the received decorative surface will depend on the type of solution used and the presence of coloring elements in it, which are not always added.


Color

It makes no sense to leave plaster that imitates brick in its natural light gray tone. This is why it is painted. In this process, there are many design options and complete freedom of choice, it all depends on your taste. Natural brick has different shades, so you can mix several options of colored pigments, achieving better visual similarity.

You can first apply a layer of paint of one color, and after a few minutes create a different color or give individual bricks a more bright look. There is a variety of shades in natural brickwork, so the decorative coating that imitates brick can have many tones.




You can experiment with colors without fear of ruining them, bricks are currently produced in a variety of colors - from bright to dark. And few people will be able to guess that the “masonry” is fake. The only thing that can ruin the look of the interior is the inconsistency of the imitation masonry color scheme with furniture or floor covering. Therefore, when covering, choose matching tones.


Also, a decorative coating that imitates brick is made with your own hands using tape. This process requires construction tape with a width equal to the masonry seam. Then on wall covering, which is finished with plaster imitating brick, horizontal and vertical lines corresponding to the connecting seam are drawn using a ruler. It should be taken into account that the vertical lines through one horizontal row are shifted by half a brick. The drawn strips are painted over their entire length with paint similar to the color of the mixture being applied, and after drying, tape is glued to the painted lines.

Be sure to first glue the horizontal stripes, and only then the vertical stripes; if the order is different, it will be difficult to remove them later.



Then a layer of decorative plaster is applied to the glued tape, while smoothing and leveling it. Smoothness will depend on your preference for embossed or perfectly smooth decor.

As soon as the applied solution begins to harden, remove the tape. A little effort is enough to pull the horizontally pasted strip, and the entire structure will easily come off. After complete drying, you can use any method finishing decorative brick wall.


Not everyone can afford an expensive option for wall decor, and if you have to work with your own hands, then decorative plaster may be the most affordable option. You cannot do without preliminary leveling of the walls, but at the same time you will save usable area in the room.

Decorative plaster for brick: preparatory work

First, as expected, remove the layer from the wall old plaster, or wallpaper - in a word, the same finish. If during inspection you find cracks or potholes, they need to be filled in. cement mortar. If necessary, the corners are aligned.


The entire surface is treated with a deep penetration primer. This is necessary for good adhesion and surface disinfection. Craftsmen advise adding a little PVA glue to the primer to improve the quality of the primer.


From tools and materials you will need:

  • Container for mixture;
  • Spatulas;
  • Masking tape;
  • Master OK;
  • Level or rule;
  • Painting mesh;
  • Drill for mixing mortar;
  • Lace or thread for beacons;
  • Plaster mesh.

Before work, cover the floor with oilcloth, and don’t forget to protect your hands with gloves.


Preparing walls for plaster (video)

Do-it-yourself brick wall made of plaster: technology

The process, of course, is labor-intensive, but what’s good is that it’s creative. If you are doing this yourself, and even for the first time, strictly follow the sequence of steps.


Technology for applying plaster under brick:

  • Wall marking is needed if you are doing this imitation of brickwork only on a fragment of the wall, and not on the entire surface. Using a simple pencil, draw the outlines of the bricks. A masking tape will be needed in order to limit the space for work.
  • Prime the wall, preferably acrylic primer. This is easier to do with a foam roller. IN hard to reach places It is better to prime with a brush.
  • In order to make the finishing mass, you need to prepare water and gypsum plaster. The mixture should be thick so that it does not flow down the wall. If you want, add dye to the solution to make the future “brick” look more realistic.
  • Plaster only the area that can only be covered at one time. Next stage carry out until the solution dries.
  • A surface covered with wet plaster is ideal for creating bricks. Take any sharp object such as a knitting needle, and use it to push strips that look like gaps separating one brick from another.
  • The bricks should not be even, as if they were aligned with a ruler. Some may be larger, so the imitation of brickwork looks more natural.

You can even create an imitation of texture on the wall surface with your own hands. To do this, use a dry, hard brush to brush over the almost dried imitation of masonry.


Finish the job by sanding the wall with fine sandpaper. Decorative plaster is painted with a roller; choose shades that are most reminiscent of natural brick.

Technology for applying plaster under brick (video)

Alternative way brick imitation consists in using putty and special narrow construction tape.


Do-it-yourself imitation of brickwork:

  • On a dry plastered wall, mark the seams so that the rectangles of each subsequent row are shifted towards the rectangles of the previous one.
  • Carefully paint the marked seams the right paint, wait until dry.
  • On top of this layer, glue strips of construction tape along the horizontal seam lines, and paste short vertical strips of tape on top of them.
  • On top of this tape, apply a fairly thin layer of putty to the wall, smooth the surface of this layer, and leave the unevenness so that there are enough of them to create the desired texture.
  • After the putty has hardened, remove the tape. To do this, you can simply remove the horizontal stripes, and the vertical ones will be removed along with them.
  • Wait until the putty has completely hardened.

Brickwork: methods of imitation

If you are not satisfied with the option where only plaster works, the brick can be made in another way. For example, corrugated cardboard is often used, which is cut into the right quantity according to the size of the sides of the brick. You must coat each such cardboard brick with PVA glue with your own hands. Paper napkins can complete the look of imitation masonry, upper layer which will perform the function of decoupage - if you need decorative finishing fragment of the wall, it's very a good option.


What else if not just plaster? Brick can also be made by stencil embossing. This work is carried out on fresh plaster. How to do this - you use a polymer or rubber flat stencil; a relief pattern of brickwork is applied to it. Moisten the stencil with water and press it against the plastered wall. And then it is taken away from the wall, and in front of you is brick by brick.


This option is simpler than scratching out every brick, but more expensive. After all, not only plaster is required, but also the stencil itself. However, the surface will be like after the work of a team of craftsmen - everything is precise and even. This cycle needs to be repeated until you get the entire surface with imitation brickwork.

Do-it-yourself decorative brick plaster (video)

A brick wall is always beautiful, stylish, and modern. And imitation of such a wall is not the worst option, nor the most expensive, which is very important. Choose the method you like and do everything step by step.

Happy renovation!

The work consists of several stages. First, the walls are prepared for processing: you need to remove the wallpaper and level the surface using sandpaper. Then a sample is made from linoleum or brick. The standard parameter is 25 × 6.5 cm. Seams are marked at a distance of 1.5 cm around the perimeter of the workpiece. Each seam is further divided in two to accurately imitate brickwork.

The brick imitation should start from the floor, retreating 5-10 cm and moving upward. Special attention is given to the first corner “brick”, the edges of which are outlined with a pencil. The corners of the wall are the most difficult, so work starts from the edges and moves towards the center. After creating the outline of the masonry, a primer is applied using a roller. The tool ensures strong and even adhesion of the mixture to the surface of the walls. At the same time, the markings remain clear and do not smear.

Before applying the solution, masking tape is applied to the joints of false masonry: first horizontally, then vertically. The gluing occurs with an overlap. The solution is made from plaster and tile adhesive in a ratio of 50:50. It is applied using a spatula or by hand, after wearing special gloves (the latter method is quick and easy). Immediately after treating the wall with the mixture, you need to remove the tape - this is the main nuance of the technology. If you hesitate, the mixture will not allow the material to be pulled off, and there will be no space between the fragments. Therefore, gypsum is not used to imitate brickwork due to its instant drying.

If the solution was applied by hand, that is, unevenly, it is necessary to shape the masonry using a spatula, chisel or tablespoon. Other methods are also used, but this one is the simplest and most accessible.

After the solution has dried, the surface of the do-it-yourself brick imitation made from tile adhesive and plaster can be painted, although many leave everything as is. The wall is cleaned and leveled with a broom, sandpaper or brush. Then it is primed completely, along with the seams, and paint is applied.

How to finish a brick wall with plaster yourself?

It is necessary to use a steel spatula 5-10 or 20-25 cm wide. Approximately 10-15 liters of solution will be needed per area. The wall is first primed, then gypsum plaster is applied to it with a wide spatula and leveled. The solution dries, then markings are made on it using a rule up to 2 m long. Using the sharp end of the tool, you need to draw seams half a centimeter to a centimeter wide. The plaster is then removed using a scraper. Standard depth seams is 3-6 mm. Plaster can be removed with a chisel or construction jointer.

Cutting is done first along horizontal, then along vertical lines. The surface is leveled and the plaster is allowed to dry. Excess is removed with a sponge or rag. If you want to make an imitation of brickwork, the wall is painted in two stages: first it is tinted with a spray or brush, then the color is applied to the “bricks”. To array for a long time remained durable, do not combine gypsum plaster and cement tile adhesive.

Do-it-yourself imitation of a brick wall made of polystyrene foam

Suitable for this purpose foam tiles for a ceiling with no patterns. It is better to make “bricks” measuring 150 x 70 mm, since figures that are too voluminous will look unnatural. First, markings are made using any available material, taking into account seam allowances. Using a toothpick, straight lines are pressed onto the markings. Use a sharp object to push to the end of the line.

You need to cover the wall with “bricks” by applying tile adhesive to the material. Imitation brick wall made of polystyrene foam from floor to ceiling. The seam between the “bricks” is 1-2 mm. After this, the cladding is ready for painting. A large amount of paint is applied to the seams to make the masonry as close as possible to natural.

Natural brick wall

To create such a wall, simply remove the trim from the brickwork, improve its appearance and paint or varnish it. First, the surface is cleared of the finish using an emery disc and grinder. To remove visual defects and unevenness, a special mixture is used, which is applied to the joints between the bricks. Finishing procedures are completed by covering the wall with special varnish or wax. They are suitable for processing walls made of natural bricks. To avoid the glossy effect on the wall, it is enough to sand the wall with fine-grained sandpaper until it becomes matte.

Tiles as a way to imitate brickwork

To create fake masonry, take tiles made from different materials. Ceramic products have such advantages as lightness, variety of surfaces (matte, glossy), ease of installation, and compactness. If you need to cover a surface with geometric complex parameters, this product will come in handy. It is important to use the tiles carefully: they are fragile and cannot withstand impacts. Clinker products made using burnt shale clay are durable and easy to install, and are distinguished by textured or smooth surface. Gypsum tiles, which are a mixture of dyes, water and gypsum, are abrasion-resistant, cheap and lightweight. It is not used in damp areas due to its ability to absorb moisture.

Installation begins with removing the previous coating and leveling, plastering and priming the wall. Markings are applied to the surface. Gypsum tiles begin to install from the floor. First, a rail is attached to the bottom of the wall, along which the first row is mounted. For fastening, gypsum putty is used - it is applied to a spatula, then to the tile. The material is pressed against the wall, but not too much, to avoid cracking. Excess putty is removed. All subsequent rows are installed with a spacing of ½ tile for a reliable imitation of brick laying. To ensure that the rows are perfectly even, clamps are attached to the space between the seams. For getting standard size Brick tiles are cut into the required pieces with a hacksaw.

The seams are formed after installation of the fabric. Rubbing occurs using putty. To give the space between the seams a relief, use half of a cut tube with a diameter of 10 mm. After the material has dried, the wall is treated and painted. Installation of clinker tiles occurs in the same way as in the case of gypsum tiles. Any tile must be laid in rows from the corner.

Imitation of a brick wall in the hallway

Imitation of brickwork in the corridor, made in white, visually expands the space. The seams between the fake bricks are not highlighted in a different color, but have a characteristic relief. A similar imitation can be performed on both walls. Together with wood-look laminate, “bricks” create a special style.

The hallway has imitation brickwork in a contrasting color. Here the seams between the fake bricks are painted dark, which sets off the whiteness of the “bricks”. This imitation is the closest to real masonry.

Here, imitation red brick masonry is used to decorate the wall in the hallway. This wall design creates a contrast with the light ceiling. The space between the seams is not highlighted with a different color, but is treated with plaster.

In this hallway, all the walls are lined with fake brickwork. The seams are not distinguished by a different color, but are characterized by the same color as the “bricks”. Zoned wall painting is presented: one is white, the other is dark gray. This method of painting creates contrast in the corridor.

Decorative brick in the living room

The living room, one wall of which is decorated with brick, looks modern and simple. The masonry is distinguished by its relief. The irregularities of the “bricks” help create naturalness and ease. White color walls with decorative bricks visually expand the space and add modernity.

Fake masonry from decorative brick this room has a smooth topography with clearly defined seams. All canvas is painted in Brown color, which creates a contrast with the light part of the living room. This type of cladding gives the room simplicity and elegance.

Imitation brick in the bathroom

Imitation of brickwork in the bathroom is created from tiles. The room is decorated in one color - white. The seams are clearly defined, painted in dark tone, making them stand out against a white background.

Imitation brickwork in the bedroom

Brickwork in the bedroom gives the room a cozy and modern feel. Here the surface is flat, clearly defined, with a defined relief. The seams between the “bricks” are not highlighted in a contrasting color, creating one canvas with the masonry. Against the background of such a wall, interior items with contrasting colors look good.

This wall is made of foam plastic. This explains uneven terrain, unclear seams between the “bricks”. The surface is uniformly painted in rich Blue colour, against which light interior items are favorably shaded. The colors are pastel, calm tones, suitable for the bedroom: they are peaceful and put you in a peaceful mood.

Imitation of brickwork on the balcony

Decorating a balcony with decorative brickwork gives the room a modern feel. The imitation is created from champagne-colored plaster and clearly defined relief. The surface has irregularities, due to which naturalness is achieved. The seams are painted dark color. This creates a contrast in the coating. The “masonry” is made with deliberate irregularities.

If the balcony is planned to be tiled in pastel light colors, for this purpose, you can use imitation brickwork. Here, fake “bricks” are combined with the smooth surface of the walls. The masonry has a marked relief, the seams between the rows are recessed inward. Applying champagne or Ivory visually expands the space.

Imitation of brickwork in the kitchen

Imitating brickwork in the kitchen helps give the room originality, modernity and naturalness. Usage light colors contributes to the visual expansion of space. Brickwork is used only on kitchen apron. Its surface is uneven and its relief has roughness.