Finishing the toilet with panels: list of materials and tools, preparation of the room, installation work, filling the sheathing and covering the ceiling. Finishing with plastic panels: decorating a toilet Finishing a toilet with plastic panels using liquid nails

Modern market offers a variety of finishing materials practical solutions for finishing bathrooms. Until recently, those who were planning to renovate their toilet had only two options - painting the walls or tiling tiles. Now you can choose from several available options, each of which has its own advantages and disadvantages.

In today's article we would like to tell you about one of the easiest and convenient ways finishing of walls and ceilings in the bathroom - plastic panels. You will learn about the features of this finishing material, the basic principles of working with it, as well as how to choose the right plastic panels for the toilet.

pros

First, let's look at positive sides using plastic panels as finishing material for the bathroom. The list of advantages of these products is quite impressive:

• Low price. This method of surface finishing is one of the most cost-effective. It would be cheaper to paint with water-based emulsion.
• Easy to install. Plastic panels do not require special repair skills. Even those who have undertaken repairs for the first time can cope with their installation.
• Fast installation. Installation of one PVC panel takes just a few minutes. Since bathrooms usually have a very small area, all the work will take you very little time.
• No need for surface preparation. There is no need to level or plaster the walls for plastic panels.
• Low maintenance requirements. PVC is a waterproof material that perfectly tolerates wet cleaning and contact with various detergents. Therefore, keeping the walls in the toilet clean will not be difficult.
• Wear resistance. Despite the fact that plastic is a fragile material, if you do not subject it to strong mechanical stress, PVC panels will last you quite a long time.

Minuses

However, plastic panels have not only positive aspects. Negative qualities This finishing material does not have many, but they are still present, so one cannot remain silent about them. So, the disadvantages of PVC panels are:

• Instability to heat and fire. Plastic panels are deformed under the influence high temperature, therefore you should not place heaters and heated towel rails close to them. In addition, plastic is not a fire-resistant material: it can catch fire if it comes into contact with fire. Therefore, you need to be careful when smoking in the toilet.
• Large dimensions. At first glance, it seems that the plastic panels are absolutely flat, but in fact they can be up to 2 cm thick. In addition, a few more centimeters of space are often “eaten up” if the walls in the room are uneven. For large bathrooms This is not critical, but in small toilets this can become a real problem, since it will not allow the maximum use of the tiny area.

Types of panels

Plastic panels intended for finishing walls and ceilings in the bathroom come in several varieties.

Leafy

The most popular type is sheet panels, which are rectangles from one to one and a half meters long. The thickness of such panels is 0.3-0.6 cm. They can be plain, with ornaments or imitation of natural structures - wood or stone. It is most convenient to work with sheet panels due to their large dimensions.

Rack and pinion

Slatted panels for finishing bathrooms are used much less frequently. They are most often used for outdoor work or large premises. This type of plastic panels looks like long narrow strips. The length of such panels is from 4.4 to 3.7 meters, and the width is from 12 to 30 cm. Slat panels imitating wooden beams look especially impressive.

Stacked tiles

The least common type of plastic panels are type-setting tiles. They are squares different sizes, which allows you to lay out various patterns on the walls and ceiling, like a mosaic. The elements are connected through grooves in the panels, and everything is held together special glue or clamps.

• If you want to purchase a product with maximum strength, choose plastic panels with a thickness of at least 0.8 cm. In addition, pay attention to the number of “ribs” on inside– they give additional rigidity.
• The quality of plastic panels can be determined by its appearance. Take a close look at the front of the product: the paint should be applied evenly, and the design, if there is one, should be clearly printed.
• As with wallpaper, the color is the same wall panels and different batches may vary by several shades. Therefore, buy products only from one batch.

The high cost of wall panels does not always indicate the same high quality, so price should not be the determining factor when choosing. However, material that costs significantly less than its counterparts from other manufacturers is usually not made in good faith.

Preparation and stages of repair

Before you begin finishing the toilet with plastic panels, you should carry out some preliminary work. By this stage of the repair, you already need to install the toilet, level the floor, lay it out ceramic tiles or cover with linoleum.

Experts advise preparing plastic panels for installation and further use by treating them antiseptic. This will protect the material from exposure to heat and moisture, so there is no need to worry about the appearance of fungus and mold.

• Stage 1. Installation of the side posts, which will serve as the basis for the frame.
• Stage 2. Lathing the structure with slats and cross members.
• Stage 3. Attaching plastic fittings.
• Stage 4. Cutting and installing plastic panels.

Basic principles and installation

Let's consider each of the above stages of work in more detail.

1. One rack should be placed in each corner of the room. At the same time, they should not be in contact with the floor and ceiling, so we place some material between the racks and surfaces. After the structure is fixed with screws, the temporary support will need to be removed. The side posts must be placed plumb so that they are strictly parallel. We maintain a step of 0.3-0.4 meters between fasteners (we use screws as fasteners).
2. The sheathing of the side posts is done with wooden blocks along the perimeter of the structure at the top and bottom. The fasteners should be screwed in at an angle of 45 degrees - this way we can securely fix two slats at once. Next, the slats need to be secured to the walls using self-tapping screws. This is the main frame, which, if necessary, can be supplemented with side posts or cross bars. Step between frame elements should be about 0.5 meters.
3. We nail the plastic fittings to the frame using nails and a hammer. The fittings need to be cut at an angle of 45 degrees - this way it will fit more tightly. Since PVC panels are quite flexible, we install fittings, including in the corners. If there is a gap between the slats and the wall, fill it with scraps of plastic, then hammer in a nail. Nails for installation should be selected with large flat heads. In order not to damage the plastic elements when driving nails, the final blows are performed not on the head, but on the protective attachment (for example, you can use a nail).
4. The final stage, when correct installation frame and fittings, takes very little time. We cut plastic panels using a hacksaw. At the same time, the size of each sheet should be a centimeter and a half less than the space prepared for it, since the missing length is compensated by plastic fittings. We insert the cut sheet into the grooves and attach it to the slats. We insert the next sheet into the previous one, then also nail it to the crossbars.

We mount the last panel a little differently. We cut it along its entire length, then move it into the corner until it stops and drive it into the lock of the previous panel using a thin screwdriver. It will not be possible to fix this panel with nails, so you need to provide the most for it in advance. inaccessible place in room.

• Before you start purchasing materials and decorating the toilet, sketch out a simple design project for the future room. Think not only about color scheme and about the placement of interior elements: it is equally important to provide for the location of windows, niches in the walls, plumbing box and ventilation.
• Make sure you have everything at hand in advance necessary materials and tools. In addition to the plastic panels themselves, you will need: a metal profile, wooden blocks, nails, screws and self-tapping screws, hammer, silicone glue, building level or a plumb line, a hacksaw or cutter, a hammer drill with a set of drills.

For tips on planning the design of a toilet with plastic panels, read another article.

Do-it-yourself apartment renovations are always a source of pride for any home craftsman. But what if you have absolutely no experience in construction and finishing?

In this case, it is better not to touch complex rooms, such as the living room or kitchen, but you can practice on finishing the toilet. First of all, this is the most small room There is not a wide variety of finishing materials in the apartment either. In addition, if in the end nothing works out, you can turn to specialists, and they will redo everything without significant damage to your wallet.

The most common material for finishing a toilet is plastic panels, and it’s not just the ease of installation, there are a number of advantages that speak in favor of this option:

• A wide variety of colors and patterns that are great for decorating a toilet.
• Easy aftercare. Plastic panels are not at all afraid of water and detergents.
• Minimum financial costs for Finishing work, even taking into account all the necessary components.
• No need for a huge number tool. Any home craftsman will have everything you need to decorate a toilet with plastic panels.

Selection of plastic panels for finishing the toilet

As often happens, due to the high demand for plastic panels, many unscrupulous manufacturers have appeared on the market. It is very difficult to determine the quality of plastic by eye, and to the average buyer they all seem the same. But this is not so, and in order not to become a victim of scammers who skimp on the quality of their products, you need to follow a few simple tips:

The correct choice of panels for the toilet is already 50 percent the key to a successful renovation. It's much easier to spend an extra hour in the store than to redo all the trim on next year, or even earlier.

Important ! When buying plastic panels for finishing a toilet, you should always take two or three segments in reserve.

If at the end of the repair it turns out that the initial calculations were incorrect, the same panels may no longer be available in the store.

Preparation for installation of plastic panels

A good master, any repair begins with preparatory work and making lists of everything needed. If this is not done, you may have to run to the hardware store more than once to get the missing materials or tools. Often, this takes much more time than the entire renovation, especially when it comes to such a small room as a toilet.

List of necessary materials for finishing the toilet

• Plastic panels with a small margin.
• Decorative elements: corners, baseboards. You also need to take it with a reserve.
• A wooden beam no more than 2 cm thick. The quantity is determined based on the installation horizontally, with a distance of approximately 30-50 cm.
• Impregnation for wood that prevents rotting, and a brush for applying it.
• Primer for walls with an antibacterial effect and a roller for its application.
• Dowels with a diameter of 6 mm and a length of 60-80 mm.
• Staples for a construction stapler.
• Glue for plastic. Will be needed to install external decorative corners.
• Self-tapping screws for wood. Will be needed to finish the riser in the toilet with plastic panels.
• Polyethylene film or thick fabric to protect the plumbing in the toilet.

Advice ! No need to save on consumables such as screws or staples. Fasteners are never superfluous in the household, and in finishing work, their lack can affect the service life of the entire repair.

List of necessary tools for finishing a toilet

• A hammer drill or hammer drill with impact mode, as well as a drill for it corresponding to the selected dowels.
• Hammer.
• Pencil, tape measure.
• Hacksaws for wood and plastic, or a jigsaw.
• Sharp construction knife.
• Metal spatula. Needed to remove old paint from the walls, if there is one.
• Construction stapler.
• Level with horizontal and vertical indicators.

Warning ! You should not cut timber and plastic panels with a grinder. As a result, a lot of acrid smoke, which the neighbors may mistake for a fire, and then you will have to explain it to them for a long time.

When both lists are collected and everything you need to finish the toilet is at hand, you can get to work.

Preparing the base for plastic panels

The quality and durability of any finish largely depends on the preparation of the base. Unlike more complex rooms in an apartment, finishing a toilet does not take much time and effort, so you need to pay attention to each stage Special attention. It’s better to spend two extra hours today than to redo everything later.

First of all, you need to completely clean the walls and ceiling of the toilet from old decoration or paint. This is done using a spatula and a light hammer, which is used to tap the surface. A coating that has become unusable will immediately disappear.

Next, the bars are prepared. They must be cut to the required length based on horizontal mounting to Wall. When all wooden elements When ready, they are treated with impregnations and taken out to dry on the balcony or staircase.

Important ! The size of the bars should be a few centimeters smaller than the toilet room. This is necessary so that the tree has the opportunity to expand.

In the meantime, while the bars are drying, there is time to continue preparing the walls in the toilet for finishing. They need to be treated generously with an antiseptic primer; it prevents the formation of mold and harmful fungi. Impregnation is done using a foam roller. To dry completely, when room temperature, it takes about an hour, which means you can take a short break and catch your breath.

Installation of wooden sheathing under plastic panels

When the walls in the toilet and the wood are completely dry, you can begin fastening. First of all, fix the block a couple of centimeters above the floor, along the entire perimeter of the toilet room. The timber is passed under the ceiling in the same way.

If the ceiling in the toilet will also be finished with plastic panels, then lathing is needed on it too; the fastening technology is no different from the wall one:

1. The block is applied to the surface, and using a hammer drill, a hole is drilled through the tree into the hay. The first fastening should be approximately five cm from the edge. A dowel is driven into the hole. The second edge is attached in the same way. Now that the block is fixed, it is further strengthened, with a step of 30-50 cm between dowels.
2. When the bars around the perimeter of the toilet room are installed, use a tape measure to measure the distance between the lower and upper bars. It is divided into two, and another beam is attached exactly in the middle of the wall.
3. The resulting two sections are once again divided in half, and the beam is placed again. This is done until the distance between the guides is approximately 50 cm.
4. Certain difficulties may arise with communications, which also need to be finished with plastic panels. To do this, boxes are made from the same block as the sheathing, which are attached to the wall and floor of the toilet. You can connect the bars together with wood screws.

Advice ! if spotlights are planned as ceiling lighting in the toilet, the block must be mounted below the ceiling, at least 15 cm. This is done using profile fasteners.

You can watch the video in more detail on how this is done.

Installation of plastic panels in the toilet

Before installing plastic panels, it is necessary to attach guide moldings to the corners of the toilet and to the ceiling.

All finishing strips are fastened with staplers to the bars

When installing plastic panels in a toilet with your own hands, always start from the left edge and the ridge to the corner. Using a construction stapler, fastening brackets are driven into the corner groove and ridge on the other side of the panel.

Important ! The first panel must be installed strictly in level. All other finishing elements will be oriented towards it.

The second plastic panel is inserted into the groove of the first and its ridge is also fixed with brackets along each wooden guide. All stages of installation are clearly shown in the video

After the walls of the toilet are completely covered with panels, the boxes covering the communications are finished. Here, perhaps, each panel will have to be cut to length; subsequently, these places will be covered with decorative corners.

In the same way, plastic panels are installed on the toilet ceiling. But here it is important to immediately make holes in the places of the lamps and bring the electrical wires out.

Installation of decorative elements on plastic panels

The easiest way to use it is to decorate the toilet outer corners, they are much more convenient to install and are not inferior in quality to those into which plastic panels must be inserted.

Plastic glue is applied to the corner and applied to the junction of the panels. Good glue It sets in a few seconds, so it is important to have time to glue the corner before it dries.

Using the same glue, the genitals and ceiling skirting boards. Any excess glue can be removed with a soft cloth, and at this point finishing the toilet with plastic panels with your own hands can be considered complete.

The matter remains with installing the necessary accessories and lamps, but this is a topic for another discussion.

Conclusion

As you can see, there is nothing complicated about decorating a toilet with panels yourself. All stages of repair will take a maximum of two days. Even if it's the first do-it-yourself repair in an apartment, it will allow you to gain invaluable experience, and perhaps the next step will be more complex premises, which also require repairs and finishing.

And in order to avoid the most common mistakes when renovating a bathroom, you can watch the video

For every home craftsman, repairs done with one's own hands are a source of special pride. However, what to do if the apartment owner has no experience in construction and finishing work? In such a situation, it is better to refuse to carry out repairs in the living room and kitchen with your own hands. To gain the necessary experience in renovating premises, you can start small - perform finishing work in the toilet.

This choice is quite logical, since the bathroom is the smallest among the premises of the apartment. In addition, the market offers a wide variety of materials, which allows home handyman When carrying out renovation work in this room, implement absolutely any design. Ideas for decorating a toilet can be found on the Internet. Even if DIY toilet repairs end in failure, there is always the opportunity to turn to real professionals. They will fix all the bugs in the design of the toilet and will make the room beautiful.

When creating the design of a toilet, many apartment owners use material such as plastic panels. They are inexpensive, and with their help you can carry out bathroom renovations yourself.

Types and characteristics

PVC panels are made by pressing the original liquid mass through a molding hole. As a result, air space is formed in the panels. This feature of the material ensures its low weight. Manufacturers produce plastic panels in the following sizes:

• width - 12.5-50 cm;
• length - 260-300 cm;
• thickness - 8-12 mm.

According to such a criterion as the area of ​​application, plastic panels are divided into wall and ceiling. The former are distinguished by higher strength characteristics and have good resistance to mechanical damage. If we talk about ceiling ones, then their feature is good flexibility and minimal weight.

Many people, when it comes to bathroom renovations, opt for PVC slats. They make this decision based on the advantages of this material. Among his most significant advantages The following can be included:

Disadvantages of PVC panels

Like any material, PVC panels have certain disadvantages. Apartment owners who are planning to DIY bathroom decoration.

When finishing a toilet with this material, it is fixed on guides. As a result, the free space in the room decreases. This will especially not please those apartment owners who have standard separate bathrooms.

If your apartment experiences a flood, the task of drying the room will become quite difficult. Water will easily seep into interpanel seams, and will evaporate long time. This can lead to unpleasant phenomena such as mold and mildew. In some cases it becomes necessary to partially dismantle the panels.

Selection of plastic panels for finishing the toilet

When carrying out renovations, every apartment owner, of course, strives to obtain an interesting room design as a result. This desire arises not only when renovating a living room, but also when tiling a toilet, which should also look attractive. Many people opt for plastic panels, which are inexpensive and easy to install material.

You can get a beautiful toilet if you approach the task of choosing it correctly. And this is not so easy to do. And it’s not just that there is a wide variety of PVC panels on the market. Often unscrupulous sellers offer defective products. To really buy quality material When choosing plastic panels, you need to remember the following recommendations:

• plastic panels that will be used to decorate the toilet in own apartment, must be made of PVC with additives that increase the elasticity of the material. The fewer there are, the more fragile the plastic is. The presence of additives in the composition of the material can be determined quite in a simple way. You need to take the panel at a distance of arms apart and begin to bend it. This should be done until you feel strong resistance. If the plastic is high quality characteristics, then it can be easily bent into a ring. The worse the quality of the material, the smaller the bending radius;
• When choosing PVC panels, you should pay attention to the material from which the slats are made. There should be no odors coming from it. If you smell a chemical smell, then you should refuse to purchase such panels and look for something else.

How to cover a toilet with plastic panels?

Finishing a toilet with plastic panels with your own hands is not challenging task. If you have the skills to work with tools, then you can easily master the installation of PVC panels. Proper implementation of this work will allow you to create an interesting design in the toilet. To realize your desire - perform quality toilet repairs in the apartment, you need to find it in your schedule free time and prepare the necessary materials and tools before starting work.

Of course, to create beautiful toilet in your apartment, you cannot do without materials and tools. To cover a toilet with plastic panels you will need:

You shouldn’t immediately rush to the store to purchase panels. First, you should measure the area of ​​the toilet in which you plan to carry out finishing work. When you receive material calculations, you should add 15% to this amount, which will be used for cutting.

Preparatory work

For many apartment owners, covering a toilet with PVC material is the best solution when renovating a bathroom. For that so that everything goes smoothly and in the end you got a beautiful toilet with interesting design, repairs in this room should begin with preparatory work. Experts recommend that the first step is to remove old material from the walls. finishing material. This will slightly increase the usable space of this room.

Even before starting work, replacement work should be carried out water pipes and electrical wiring. Before installing the material, the walls should be treated with a primer. You should choose a primer that has antibacterial properties. In this case, when high humidity Mold and mildew will not appear on the walls under the panels.

Before you start working with plastic panels, you should also think about where the sink and cabinets will be placed in the bathroom. Additional strips should be provided in these places. It is on them that the accessories will be secured. Before you practice installation of material, it is necessary to keep the lamellas at room temperature for several hours.

How to decorate a toilet with plastic panels: installation

The first step is to secure the guides from the wall to the wall. aluminum profile or from plastic slats. IN horizontal orientation installation in progress wall sheathing. The ceiling is laid perpendicular to the direction of laying the material. Between the guides a step of 50 cm is maintained. Some designers opt for diagonal fastening material. If such original version design you like, you should know that its implementation will lead to increased material costs.

You can immediately fix the U-shaped corner profiles. Next, the first panel is carefully inserted and secured using prepared self-tapping screws. Some craftsmen use construction stapler. However, this fixation option can only be applied to wooden sheathing, which is a completely unsuitable material in a toilet.

Next, step by step, you should attach the next panels, which must be pressed very tightly to the previous ones. The crucial point when installing PVC slats in a toilet is the fastening of the last panel. It is necessary to accurately calculate the remaining width. If you do not pay attention to this point, you can ruin the entire structure.

You can move on to work such as tiling the ceiling in the toilet only after all the work on installing the panels on the walls has been completed.

If your plans include placing spotlights in the toilet, then you need to cut the holes to size lighting fixtures. In addition, it is necessary to make holes in the places where sockets and switches are installed, as well as ventilation pipes. Cutting material for finishing walls and ceilings must be done from the front side using a jigsaw or hacksaw with a tooth pitch of 1 mm.

Once the panels are secured, you can proceed to installation. decorative plinth. You can choose products made from plastic or ceramic.

Conclusion

When renovating a toilet, many apartment owners choose PVC panels for surface finishing. To make it work beautiful finish toilet with plastic panels, photo design projects on the Internet should be studied first. This will help you decide on the design of the room.

It’s not difficult to create a beautiful toilet in your home. You just need to find free time and prepare materials and tools. High-quality repair toilet with plastic panels will allow you to get an aesthetic design of this room. Her original design will be a source of pride for a home craftsman.

By far the most popular view is to furnish a room using PVC panels. Separate bathrooms are often finished with plastic panels. And this is not surprising, because PVC panels are almost invisible in small rooms, so their disadvantages take second place. In addition, there are now many plastic panels with beautiful design for every taste, so you can make the toilet or bathroom an exclusive and creative part of your apartment. But how right decorate the toilet PVC panels with your own hands? Read the article, watch the video and bring your ideas to life!

PVC panels for the bathroom: pros and cons

• Low cost. If you choose between tiles or decorative stone, then PVC panels will cost much less.
• Light weight, which makes it easy to transport and install the panels. In addition, plastic panels are easy to cut.
• Quick installation that does not require complex fastenings.
• A large assortment will allow you to choose the appropriate model of plastic panel.
  PVC does not swell when exposed to moisture and their surface can be easily cleaned of dirt.
• Ease of use. In the event of a pipe break or other troubles that can happen at any time, PVC panels can be easily disassembled and put back in place.
• Resistance to heat and absence of harmful substances.

The disadvantages of PVC panels are: toxicity during combustion, as well as increased fragility. Therefore, you should be extremely careful with such material.

What is worth remembering when decorating a toilet and bathroom with PVC panels with your own hands?

When working with PVC panels yourself, it is important to know how to cut them correctly. If you are dealing with plastic panels for the first time, then stationery knives or cutters will be useful to you, but you can also use a small hacksaw. Since PVC panels are quite thick, cut off stationery knife It can be equally difficult on both sides, so it’s better to use a hacksaw. It is worth noting that when cutting with a hacksaw, the joints will be rougher than when cutting with a knife.

Thus, having correctly calculated the area, you can easily select required quantity plastic panels and decorate the toilet with your own hands.

The process of finishing a toilet at home with PVC panels

Start finishing the toilet walls with your own hands by building a frame. Then (if necessary) place insulation in it and press it. Next, finish with plastic panels from the corner of the toilet. To do this, secure the first panel to the frame in a vertical position. For accuracy of work performed, use a level.

When you have secured the first panel, you need to insert other PVC panels one by one. If the edges are smooth, there should be no difficulties. The panels must match in design. If you don’t want to spend a lot of time selecting a design, buy monotonous plastic panels.

When decorating the toilet with plastic panels with your own hands is nearing completion, and there is only one place left where there is no panel, simply cut right size and insert the closing part into the groove of the penultimate one and secure it well.

Thus, the entire process of work does not take much time, and decorating the toilet with plastic panels with your own hands is a fairly convenient and cost-effective option for many.

With such a renovation, the walls in your toilet will look beautiful and concise, hiding wall defects, as well as various additional communications.

See also video: decorating a toilet with plastic panels with your own hands

When it comes to choosing a material for renovating a toilet, many people wonder how to decorate it: tiles, wallpaper or plastic.

Let's consider the last option - decorating the toilet with PVC panels yourself.

Reasons for choosing of this material enough. It is highly permeable and easy to clean. Low cost makes it accessible to a wide range of consumers.

In addition, plastic can be used even with uneven walls and the ceiling. It is easy to install and install, and is also characterized by good wear resistance and practicality in operation.

Despite all the advantages, this material has its disadvantages; you should familiarize yourself with them before making a purchasing decision. When ignited, plastic can release toxic substances, despite all the manufacturers' assurances about fire resistance.

Despite the fact that the cladding process itself is quite simple, the quality of the work done depends on many points, from the choice of material to the carrying out of all the main work.

They reduce the space by about 3 centimeters and this must be taken into account when installing plumbing fixtures, doors, and if the room does not have significant dimensions.

Selection of finishing products and fasteners

Before choosing panels based on pattern, color and aesthetic perception, you need to pay attention to their rigidity, design and size.

Rigidity or strength is important because the walls will most likely be loaded with loads in the form of shelves and various accessories. Ask the seller to show more durable models; the higher the rigidity, the better.

Now let’s talk about how long and wide the panels should be. The average width of plastic panels is 12-25 centimeters. For a beginner with no masonry experience, it is recommended to take products about 14-15 centimeters wide. The length is always standard and equal to 3 meters.

TO this type materials must be purchased, endings and plastic corners. You cannot save on this purchase, since the fasteners complete general form repair. It's better to take extra.

Average, plastic trim It lasts about 10 years, so choose panels according to your taste, but it’s better to use neutral colors, with patterns you like, because you won’t be using the room for a year.

The next important purchase is slats. It is recommended to buy slats with square section, this will serve as additional strength to the frame. The slats should be straight, compare the entire stack you are going to buy. If you don’t have self-tapping screws, screws and nails like tar paper at home, you’ll have to purchase them.

Surface and sheathing preparation

This is the second stage from which you begin finishing the toilet with PVC panels yourself. Read the instructions supplied with the products; usually the manufacturer gives his recommendations for installation.

There is nothing complicated in preparing the surface: the main thing is that it is dry. If there was wallpaper in the toilet before, it needs to be removed. But if there were originally tiles, drywall or plaster on the wall, then you can sheathe over them.

If mold is present, the surface should be thoroughly cleaned and disinfected.

The lathing can be made of metal, plastic, wood. Which lathing is better? If indoors high humidity, That wooden sheathing It may not last long, but there is a way out - treat it with an antiseptic.

With plastic and metal lathing easier to work with because they are attached with clips. The slats should be perpendicular to the panels. The distance of the structural elements can be about 30 centimeters, but if necessary, you can safely increase it to 1.5 meters.

For any unevenness on the wall, it would be correct to place a wooden, plywood, or plastic spacer under the slats to secure it. You can insert insulation into the frame.

Panel installation work

The frame is mounted from one of the corners. The first guide is installed here, vertically. This important point, in which no mistakes should be made, otherwise in the future everything will look crooked.

Next, plastic strips are attached to each other’s grooves. Check that the elements of the pattern match completely and that the edges are even.

Important points you need to know when decorating a toilet with PVC panels yourself

It will be better to cut plastic with a hacksaw, a special cutter or a stationery knife.

Before renovations begin, the room must have a floor tiled and a toilet installed.

If the slats are treated with an antiseptic a day or two before starting work, then the entire slatted base will serve for a very long time, it will not be afraid of moisture, fungus and rotting.

After completion of the work, it will be necessary to install toilet accessories and shelves. You need to think about this in advance: plastic does not hold objects larger than one kg well. Where they are expected to be located necessary elements, it is necessary to strengthen the frame sheathing.

Such, it would seem, simple work, as installation of panels cannot be rushed. Until there is reliable fastening, the material can quickly deform under significant mechanical stress.
After completion of the repair, the surface should be treated with an antistatic agent and cleaned of dirt and dust.

That's all the advice on finishing plastic panels in the toilet. In conclusion, I would like to note that when the right approach There is nothing complicated in the installation process.

Step-by-step video on how to cladding a bathroom with plastic:

This cladding option is an inexpensive alternative to tiles, but is in no way inferior to it in both decorative and performance characteristics.